Bushes & Inserts

9935 products

  • POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) REAR BEAM TO CHASSIS BUSH - Car Enhancements UK

    POWERFLEX POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) REAR BEAM TO CHASSIS BUSH

    OEM Part Number: 1805815 OEM Part Number: D65128460 Price is for 2x Bushes as required for this car INSTRUCTIONS/DRAWING   

    £93.17

  • Powerflex Rear Beam To Chassis Bush PFR19-1511 for Ford Fiesta Mk7 ST (2013-) - Car Enhancements UK

    POWERFLEX Powerflex Rear Beam To Chassis Bush PFR19-1511 for Ford Fiesta Mk7 ST (2013-)

    These Road Series polyurethane bushes use Purple 80 Shore A material as fit and forget durable alternative to the original Fiesta MK7 models part.  Ford Fiesta Mk7 ST (2013-) Rear Beam To Chassis Bush PFR19-1511 OEM Part Number: 1805815 OEM Part Number: D65128460 Price Ex. VAT: £32.35 Price Inc. VAT: £38.82 Quantity per car 2 (Price is for amount in pack)   Fitting Instructions:1. Remove the original rubber bush from the rear beam, make sure to retain the original mounting bracket.2. Clean any dirt and corrosion from the bore of the arm and file off any sharp edges.3. Push in the polyurethane bush with the larger lip diameter facing the outside of the beam, as shown in Figure 1.4. Apply the supplied grease to the bore of the polyurethane bush and press fit the stainless steel sleeve into the bore of the bush.5. Re-fit the rear beam to the mounting bracket and to the vehicle and tension all hardware to manufacturers recommended torque settings.

    £93.17

  • Fiesta ST MK7 OEM+ Front Control Arm Kit (Standard Alignment) Superpro - Car Enhancements UK

    SuperPro Fiesta ST MK7 OEM+ Front Control Arm Kit (Standard Alignment) Superpro

    Standard alignment. Fits the ST models which have a larger 14mm bolt over standard non-ST vehicles. For non-ST models, see TRC1068.This front lower control arm kit has been designed to be an easy repair solution.Offering both alignment and vehicle handling improvements. Designed not just as a repair solution but as an upgrade!Supplied as a complete kit and fully assembled with special uprated ball joints and proprietary SuperPro bushings. We have made TRC1046 by far the best choice on the market.These arms utilise the SuperPro bushings and are manufactured from a high strength material.By eliminating the O.E style rubber bushing, these arms have been optimised for longevity, durability and performance, without any unwanted NVH.SuperPro Control Arms are perfectly suited as a standard replacement and are an upgrade from the factory arms, eliminating the undesirable arm movement to maintain better steering geometry in all driving conditions.SuperPro offers a lifetime warranty on all Polyurethane products and a 3 year or 36,000 mile warranty on all metal products, end links and ball joints. This warranty covers the cost of replacing the parts in the case of manufacturing defects, material defects and is subject to a Fair Use assessment. ‹› Kit Includes: 2 x Arms 2 x Ball Joints 4 x Polyurethane Bushes 4 x Steel Tubes Shipping Weight: 6.0000kg Stock Details: Immediate Stock On Hand: -6Secondary Stock on Hand: 0 (Normally within 24 hours)2 due on 20 April 2023 Media Files: Fitting Suitable for: Ford Fiesta MK7 Front Wheel Drive (2013 to 2017)

    £256.54

  • POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) EXHAUST MOUNT - Car Enhancements UK

    POWERFLEX POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) EXHAUST MOUNT

    OEM Part Number: 1039760 / 1117761 / 1368629 OEM Part Number: 1368618 / 30657362 / 7231272 OEM Part Number: 175544 Size A=71mm B=50mm PRICE IS FOR 1X INSTRUCTIONS/DRAWING   

    £12.96

  • Complete Lower Control Arm Kit FORD FIESTA MK7 1.0 ECOBOOST 140HP - Car Enhancements UK

    SuperPro Complete Lower Control Arm Kit FORD FIESTA MK7 1.0 ECOBOOST 140HP

    Comes complete with standard alignment SuperPro bushes and ball joints as a simple and quick repair/upgrade solution. Does not fit ST models.   Fitment Difficulty:     Fitting Time: 1hr 30mins   Wheel-alignment required after fitment Kit Includes: 2 x Arms 2 x Ball Joints 4 x Polyurethane Bushes 4 x Steel Tubes Quantity Required: 1 Shipping Weight: 6.0000kg Suitable for: Ford Fiesta MK7 Front Wheel Drive (2008 to 2017) Mazda 2 DE Front Wheel Drive (2007 to 2015)

    £241.36

  • Revo MQB Engine Mount Kit Full Set with tool - Car Enhancements UK

    Revo Revo MQB Engine Mount Kit Full Set with tool

    Revo Engine Mounts More power results in more movement during aggressive acceleration. The stock engine mounts, designed to favour comfort over performance, fail to manage axle hop and torque effectively requiring you to ease off in order to gain traction. Designed to significantly reduce this engine movement, Revo engine mounts use Dual Durometer technology to minimise noise, vibration and harshness levels (NVH) while drastically improving traction and acceleration. The engine, transmission and torque mounts have been CAD designed to offer OE quality fitment with the performance benefits and quality of a Revo product. Key Features Dramatically reduce engine movement Improved acceleration and torque Dual Durometer Technology Comes with removal tool for torque mount Engine & Transmission Mount The primary design goal of the engine and transmission mounts was to provide a management system for engine movement during vehicle operation with increased power/torque, in order to retain vehicle acceleration and tyre contact during aggressive driving. The aforementioned solution must also continue to dissipate the NVH naturally created by the drivetrain. To accomplish this, the bushing design of past Revo engine mounts was retained in the MQB engine and transmission mounts, allowing Revo engineers to focus their efforts on bushing stiffness/type to accomplish the task. Torque Mount Arguably the most vital engine mount upgrade to consider, testing highlighted that the engines stock lower torque mount allowed a substantial amount of engine movement to occur. Although some improvements were noted during testing of an insert style upgrade designed to stiffen the standard mount, there was a significant increase in NVH felt in the cabin. This was dramatically reduced when completely replaced with the Revo polyurethane torque mount and also improved acceleration. Fitting the mount does not require the sub-frame to be removed, reducing installation time and the need for axle re-alignment. A Revo installation tool is included to make removal of the OEM mount and installation of the replacement as quick and easy as possible. Materials, Manufacturing & Fitment Effective design and fitment plays a principal role in managing engine movement to ensure optimal acceleration and tyre contact with the road while dissipating NVH experienced from the drivetrain. Each component has been designed using CAD technology to ensure precision fitment and is supplied with class 12.9 hardware to replace the standard fixings. To ensure optimum strength and durability, brackets and housings are CNC machined from 6061-billet aluminium and finished with an anodised coating to protect from heat and corrosion. OEM Comfort, Aftermarket Performance To achieve the optimal balance between performance and comfort, several different durometer bushings were tested on a Volkswagen Golf Mk7 GTI. Bushings were systematically tested at precise increments at each mount location. A 3-axis accelerometer was used to quantify the NVH levels being transmitted into the cabin, as well as the acceleration of the drivetrain during loading. Accelerometer data gave us a way to compare mount combinations against each other with a low data error percentage and to quantify driver comfort as well as engine movement. Supplemental data was taken from VCDS to ensure each individual test was standardised over a given throttle, RPM and speed range. The graph shows the amount of vibration measured whilst driving through the gears. Technical Documents The following documents are available to view: Fitting instructionsDownload the Revo MQB Engine Mount Instructions HERE Fitting instructionsDownload the Revo MQB Torque Mount Instructions HERE Fitting instructionsDownload the Revo MQB Transmission Mount Instructions HERE Fitment Notes Lower torque mount kit includes torque mount and Installation toolFull kit includes engine mount, transmission mount , torque mount and torque mount installation tool Vehicle Applications Audi A3 8V 2.0 TSI 2012 onwards Audi S3 8V 2.0 TSI 2012 onwards Audi TT MK3 2.0 TSI 2014 onwards Audi TTS MK3 2.0 TSI 2014 onwards Seat Leon MK3 2.0 TSI 2012 onwards Skoda Octavia 2.0 TSI 2013 onwards VW Golf GTi 2.0 TSI 2012 onwards VW Golf R 2.0 TSI 2012 onwards

    £625.20

  • POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) POWERFLEX HANDLING PACK - Car Enhancements UK

    POWERFLEX POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) POWERFLEX HANDLING PACK

    Price Ex. VAT: £269.95 Price Inc. VAT: £323.94 Quantity per car 1 PRODUCT PRICING INFORMATION The prices shown on our website are per bush.To get the total pack price you will need to multiple this price by the number of bushes per vehicle. Bush Price x Qty Per Car = Pack Price     Included within this pack are the following parts: PFF19-1531 Front Wishbone Front BushPFF19-1502G Front Arm Rear Bush, Caster AdjustablePFR19-1511 Rear Beam To Chassis BushPFF19-2001 Lower Engine Mount Large Bush 30mm Oval BracketPFF19-2002 Lower Engine Mount Small Bush 30mm Oval Bracket This Handling Pack contains a selection of parts from a complete vehicle listing, click here to see more parts available.

    £419.83

  • Powerflex Upper Transmission Mount Insert PFF19-2026 for Ford Fiesta Mk7 ST (2013-) - Car Enhancements UK

    POWERFLEX Powerflex Upper Transmission Mount Insert PFF19-2026 for Ford Fiesta Mk7 ST (2013-)

    Fits manual and DCT transmission models only. This part is designed to limit excessive movement of the upper transmission under load by providing additional stability to the mount from filling excessive voiding in the original mount. This insert is very easy to fit and is a fast way to improve shift feel and performance. This should be considered as a performance upgrade and therefore an increase in noise and vibration is to be expected. OEM Part Number: 1796438 / C1BY-7M121-AA OEM Part Number: 1536197 / 8V51-7M121-AE. Price Ex. VAT: £32.35 Price Inc. VAT: £38.82 Quantity per car 1 PRODUCT PRICING INFORMATION The prices shown on our website are per bush.To get the total pack price you will need to multiple this price by the number of bushes per vehicle. Bush Price x Qty Per Car = Pack Price INSTRUCTIONS/DRAWING         

    £46.58

  • Powerflex FORD / MAZDA JACK PAD ADAPTOR PF19-860 - Car Enhancements UK

    POWERFLEX Powerflex FORD / MAZDA JACK PAD ADAPTOR PF19-860

    FORD JACK PAD ADAPTOR PF19-860 PF19-860 is a polyurethane jack pad to fit around and protect the sill, designed to help lift stability and location, whilst protecting the underside of your vehicle. Size75mm DiameterFitment Guideline:Ford C-Max MK1 (2003-2010), Ford C-Max MK2 (2011 ON), Ford Fiesta Mk7 (2008 - 2017), Ford Fiesta Mk7 ST (2013 - 2017), Ford Fiesta Mk6 inc ST (2002-2008), Ford Focus Mk1, Ford Focus Mk1 RS, Ford Focus Mk1 ST, Ford Focus MK2, Ford Focus MK2 RS, Ford Focus MK2 ST, Ford Focus Mk3, Ford Focus MK3 RS, Ford Focus Mk3 ST, Mazda Mazda 3 BK (2004-2009), Mazda Mazda 3 BL (2009-2013)

    £22.74

  • POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) REAR SPRING UPPER ISOLATOR - Car Enhancements UK

    POWERFLEX POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) REAR SPRING UPPER ISOLATOR

    PFR19-2030 is designed to eliminate creaks and squeaks from the rear springs. We have used our durable Purple 80 Shore A material to target reliability issues of the original part, since the softer OE specified foam quickly deteriorates, even on newer vehicles. OEM Part Number: 2037363 OEM Part Number: BV2Z-5586-B Quantity per car 2 (Price is for amount in pack)      

    £70.42

  • POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) FRONT ANTI ROLL BAR BUSH 21MM - Car Enhancements UK

    POWERFLEX POWERFLEX - FORD FIESTA MK7 ST (2013 - 2017) FRONT ANTI ROLL BAR BUSH 21MM

    Please check anti roll bar diameter before ordering. OEM Part Number: C1BC-5484-DA OEM Part Number: 2002588 OEM Part Number: K1BC-5484-AB Size 21mm Quantity per car 2 (Price is for amount in pack)

    £52.70

  • Powerflex Front Upper Engine Mount Insert PFF19-2025 for Ford Fiesta Mk7 ST (2013-) - Car Enhancements UK

    POWERFLEX Powerflex Front Upper Engine Mount Insert PFF19-2025 for Ford Fiesta Mk7 ST (2013-)

    The PFF19-2025 poly engine mount insert is available from stock and backed by the Powerflex Lifetime Warranty. Although not a necessity, many of our customers fit the PFF19-2026 gear box insert at the same time for ultimate ST torque control.  Ford Fiesta Mk7 ST (2013-) Front Upper Engine Mount Insert PFF19-2025 This is an insert to fit into the original mount to limit movement of the engine to provide stability under acceleration. If fitting this to a diesel engined vehicle, an increase in noise and vibration is to be expected. This should be considered as a performance upgrade. Diagram Position: 25 Number of Bushes Supplied: 1 OEM Part Number: C1BY-6F012-BA OEM Part Number: 8V51-6F012-AJ Fitting Instructions:1. Clean any dirt and corrosion between the engine mount and the engine mount plate.2. Twist the polyurethane insert bush to open the bore along the split line and proceed to align the bore around engine mount rod. Once the bore is aligned it should allow the polyurethane bush to return to its original circular geometry. Make sure the textured surface is facing the engine mount. As shown in Figure 1, Pt1.3. Take the supplied O ring and carefully stretch it over the engine mount plate onto and around the polyurethane insert bush. The O ring should fit comfortably in the radial groove around the insert; preventing the insert from opening. As shown in Figure 1, Pt2.4. Re-fit engine mount to the vehicle. Tension all hardware to manufacturers recommended torque settings.

    £31.82

Login

Forgot your password?

Don't have an account yet?
Create account