Actuator

This actuator is suitable for the following K24 Turbo models: 2004-2007 Volvo S60R (Eng Code B5254T4) 2.5L AWD 300hp • 2004-2007 Volvo V70R (Eng Code B5254T4) 2.5L AWD 300hp • 2005-2007 Volvo S60 T5 ( Eng Code B5244T5) 2.4L FWD 260hp • 2005-2007 Volvo V70 T5 (Eng Code B5244T5) 2.4L FWD 260hp Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACS60R Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This actuator is suitable for a number of engine installations in the 850,S60,S70,V70,C70 range. There are two variations of this actuator available, FMACT5S – with a straight connecting rod, and FMACT5B where the rod has an offset or bend. Please see the fitment lists below to determine which version should fit your vehicle: FMACT5S (Straight Rod) This is compatible with the models below, with the Bosch Motronic 4.3 / 4.4 ECU fitted as standard, as seen in models with an accelerator cable. The original actuator rod is straight and suitable for the Mitsubishi TD04HL straight flanged turbo. • 850 R 1997 - 1998 • 850 T-5 1997 - 1998 • 850 T5-R 1997 - 1998 • S70 T5 1997 – 1998 • V70 T5 1997 – 1998 • C70 T5 1997 - 1998 FMACT5B (Bent Rod) This is compatible with the models seen below with Bosch Motoronic 7 and Motronic 7S ECU fitted as standard, as seen in models without an accelerator cable (drive by wire / ETM). The original actuator rod is stepped and suitable for the Mitsubishi TD04HL angled flanged turbo type. • S70 1999 - 2000 • C70 (phase 1 and 2) 1999 - 2005 • V70 (phase 1 and 2) 1999 – 2004 • S60 (phase 2) 2000 – 2004 If you have a later K24 Turbo models (2004/2005/2006 and 2007) with 6 speed manual or automatic gearbox, please see Forge Motorsport part number FMACS60R. Please select the actuator rod, straight or bent, and colour of spring in the options above. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACT5 Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

PLEASE BE AWARE THIS IS NOT A REPLACEMENT PART FOR CARS THAT HAVE ELECTRONIC ACTUATORS. WE ADVISE YOU TO CHECK WHAT YOU HAVE BEFORE ORDERING THIS ITEM. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. FMACVAG09 Application List:Golf MK5 1.4 122 TSIGolf MK6 1.4 122 /125 TSILeon 1.4 122 / 125 TSIIbiza 1.4 122/125 TSIScirocco 1.4 122/125 1.4 TSIAudi A1 122/125 1.4 TSIAudi A3 122/125 1.4 TSIEos 1.4122 TSIFabia 1.4 122 TSIOctavia 1.4 122 TSIRoomster 1.4 122 TSISuperb 1.4 122 TSI In The Box:1 x FMACVAG09 Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Fully serviceable and tuneable replacement turbocharger actuator for the Ford Fiesta MK7.5 ST180. If you require this actuator to be assembled with a standard spring suitable for the factory boost level please select Green Stock Vehicle from the drop-down list. If you require a stronger spring please select the required spring in the drop-down menu.Green – Stock SpringPurple – 13 Psi (0.9 bar)Yellow – 15 Psi (1.03 bar)Blue – 18 Psi (1.24 bar)Red – 20 Psi (1.38 bar) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACST180 Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Designed by Forge to replace the original component on the Renault Megane 225/230 Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACMEG Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Adjustable Actuator for Subaru Impreza 2006/07 WRX STi. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMAC5SUB Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.

Read more less

Adjustable Actuator for Subaru Impreza Fitted with IHI VF48 Turbo. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMAC7SUB Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.

Read more less

A replacement turbo actuator for the MK2 Ford Focus RS. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACFRS2 Actuator1 x Forge Sticker This actuator is built with a yellow coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Fully serviceable and tuneable replacement turbocharger actuator for the Vauxhall Corsa 1.0 Ecoflex. Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please note this will only fit the 1.0L models with the detachable turbuckle as shown in the image above. If your turnbuckle does not thread on to the OEM actuator then this Forge actuator will not suit your application. Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVC1 Actuator1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Adjustable Diaphragm Actuator for the Evo 9 Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACEV9 Actuator1 x Fitted Rubber Gaitor1 x Forge Sticker This actuator is built with a stock spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

IWG75 Ford Focus ST / XR5 2.5L Turbo 7psi Ford Focus ST Internal Wastegate Actuator (IWG) provides better turbo response and greater sensitivity when managing boost pressures. Designed as a direct bolt-on replacement for the factory part, the IWG is easy to install and requires no special tools or fabrication. We’ve taken the proven technology from our WG38, 40 and 45mm External Wastegates and applied it to the Internal Wastegate Actuator. Features:– Silicone diaphragm with Nomex reinforcement to withstand high temperatures.– High grade, billet aluminium construction.– Stainless steel rods and connecting clevis for corrosion resistance.– Locking Collar design cap allows for quick spring changes (Options from 3psi to 26psi available).– AIRTEC Branded product Ideal for use with any Turbosmart boost controller. Please note: Pictures are library pictures and may not relate to actual product. AIRTEC part no: TS-0941-1010

Read more less

Designed by Forge to replace the original component this uprated piston design actuator is serviceable and guaranteed for life. It is supplied with the necesary mounting bracket. This product is built with a predetermined actuator spring suitable for at or slightly above factory boost levels. The actuator can be assembled with a stiffer spring upon request. Please contact us directly concerning this process. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket. Forge Motorsport nor any of it’s Authorized Distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. Please note Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals   In The Box:1 x FMPACHG Actuator1 x Forge Sticker This actuator is built with a Green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Piston Type option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less