The Kompact EM series combines world leading electronics and 20 years of blow off valve technology together to provide rapid response. The EM series is a true plug and play upgrade for OE electronic diverter valves. Featuring patent-pending pressure control, these units are faster than OE, don't leak and don't interfere with OE control systems. Patent pending integrated pressure control True plug and play upgrade Responds 57 times faster than a blink of an eye Integrated proprietary high-temperature solenoid valve Billet construction with high temperature o-rings Available in plumb back or dual port options Leak-free design, over 400% compared to OE  The unique patent pending pressure control allows for the fastest responding valve on the market, a true plug and play upgrade diverter valve without additional hardware required, no hoses, no adapters, no brackets, just replace the standard unit.Billet construction and high temp proprietary materials allow for minimal leakage and maximum performance  Part Number: TS-0223-1066   Works on MK7 Fiesta ST180/200 & MK8 Fiesta ST (Model with valve)

Read more less

The VTA is a performance blow-off valve solution for Fiesta MK8 ST vehicles with an electronic factory diverter valve.   If you want sound with your performance (or performance with your sound!), GFB’s VTA delivers just that! By combining the proven performance benefits of our ground-breaking DV+ with atmosphere venting, the VTA delivers an aggressive blow-off sound, improved throttle response and boost recovery, as well as superior boost holding and reliability in extreme conditions. The VTA shares the successful DV+ design philosophy: “Keep what works, replace what doesn’t” This means we retain ECU control and the solenoid from the factory diverter to ensure the fastest possible response time, without the added and unnecessary cost of replacing the solenoid like some brands do. The weak part of the factory diverter has always been the plastic valve mechanism – this is the part we replace. The VTA features CNC machined billet components that last a lifetime, and we also change the valve operation method for better performance. The factory diverter valve can only operate in two states – open, or closed. When it opens fully at low boost, or during a partial throttle lift mid-corner, it causes increased lag and a noticeably non-linear boost transition. GFB pioneered the use of “pilot operation” in the DV+, which works by re-purposing the factory solenoid to control the pressure behind the piston rather than the piston itself. This allows the solenoid stroke to be much shorter, speeding up the response time and increasing the actuation force. More importantly, it allows the piston to open and close progressively in response to the amount of boost pressure present, which smooths boost transitions and reduces the lag caused by the factory diverter valve. It is this design philosophy that makes the VTA not only the best performing blow off valve solution, but also the best value on the market.  Key features: TMS Technology for faster boost recovery on gearshift and during throttle modulation Improved boost holding ability Atmosphere venting for blow-off sound Retains ECU control Simple, direct bolt-on kits include everything you need to install Manufactured in Australia in accordance with ISO 9001  VTA or DV+?  Depends if you want sound or not. Both valves are constructed with the same quality materials and valve mechanism, and both offer the same performance and reliability benefits. However, the VTA vents to atmosphere for sound whilst the DV+ recirculates the air to keep it quiet. Why choose a VTA over a “BOV spacer”? “BOV spacers” are cheap and they make sound. But that’s it. All the inherent performance and reliability issues you get with the factory diverter valve remain, because a spacer doesn’t change the diverter valve in any way. The VTA improves the operation of the diverter valve for sound AND performance. Why choose a VTA over a kit that includes a solenoid? Because there’s no performance benefit to replacing the factory solenoid, only a much higher price! If a VTA with the factory solenoid can open in a couple of hundredths of a second, why pay more than you need to?

Read more less

The new DV+ GFB’S DV+ SOLUTION COULDN’T BE SIMPLER - KEEP WHAT WORKS AND REPLACE WHAT DOESN’T. Uses factory solenoid coil for seamless integration Replaces plastic valve parts with metal for reliability and strength on chipped engines Direct-fit replacement with GFB’s TMS benefits Exclusive “pilot-actuated” valve mechanism for rapid response at high boost GFB expands the DV+ range with a direct-fit solution for the weak factory diverter valve used on many European vehicles. The solenoid coil itself from the factory-fitted valve is great- the ECU opens it faster than any pneumatic valve so why replace it? The weak point however, is the valve mechanism itself. GFB’s DV+ solves this problem by replacing the valve parts with an anodised billet aluminium housing, fitted with a brass piston machined to exacting tolerances. The end result is sharper throttle response, lightning-fast valve actuation, and it will hold as much boost as you can throw at it. Read all about the DV+ story below. Other manufacturers’ products involve replacing the entire system with a traditional pneumatic valve. This approach requires long vacuum hose runs, additional parts for tapping into the intake manifold vacuum, plus a different solenoid valve to actuate the pneumatic valve, or a ballast resistor to plug into the OE wiring loom. All these additional items result in a product that is slower, less responsive, more expensive and takes much longer to install. GFB’s DV+ solution on the other hand is more responsive, less expensive, easier to install, and doesn’t cause compressor surge/ turbo flutter. Oh, and it doesn’t require different springs or frequent re-builds either. GET BETTER PERFORMANCE, FASTER BOOST RECOVERY AND DON’T PAY FOR WHAT YOU DON’T NEED! The DV+ story: Better performance - more reliable Many late-model European cars use ECU controlled solenoid-type diverter valves. This is a good concept because the valve can react very quickly and it only opens when it needs to. However, there are some problems with these valves; The diaphragms are weak and known to rupture, especially if boost has been increased. Once this happens, the valve will no longer hold boost pressure.The plastic lip that surrounds the diaphragm is very thin and pieces can break off, potentially ending up going through the turbo. Additionally, the solenoid on the OE diverter is directly connected to the valve mechanism, which is not ideal because neither it nor the return spring are strong enough to open and close the valve reliably at high boost. With problems like this, you can see why other aftermarket manufacturers assume the best solution is to replace the factory diverter entirely, or change it to a purely pneumatic system. Unfortunately though, whilst their replacement kits might be stronger than the factory diverter, their slower response speed and lower flow do not justify the extra cost and complexity - more of a compromise than a solution. GFB has taken a different approach to deliver a complete solution that solves existing problems and improves performance, without compromise or a hefty price tag. The DV+ addresses the factory valve problems with a very simple and elegant solution. Keeping the factory solenoid, the DV+ retains all the benefits of the stock system. Also replacing the valve parts with indestructable metal components ensures strength and reliability, no matter how much boost you run. That’s not all; rather than using the solenoid to directly actuate the valve, we’ve introduced a unique “pilot-actuation” system. This means the solenoid only has to control airflow through a small passage that is then used to open and close the piston (rather than opening and closing the piston directly), so it doesn’t matter how much boost you push through it, the DV+ will open and close reliably without ever exceeding the solenoid’s capability. This feature also improves on the factory system by opening the valve progressively in response to boost pressure, so it only opens as much as required to get the job done (the factory valve simply opens and shuts, it cannot partially open if boost pressure is low), resulting in better throttle response. Unnecessary replacement kits are a compromise, not a solution

Read more less

After huge demand, Forge have developed the perfect dump valve solution for the Fiesta ST MK8 and Ford Puma ST, two vehicles that Ford launched without an OEM valve included. Similar to our early days when Ford released the RS turbo Escort, Forge developed and lead dump valve technology to give the Escort owners the same technology as Cosworth did for the Sierra - with loud whooshes and prolonged turbocharger life, this really is one the favourite modifications for the Ford enthusiasts must have bolt on products. As the engine does not have a diverter valve fitted as standard, Forge have developed a twin piston dump valve that not only gives you an incredibly loud sound when lifting off the throttle, but also increases the throttle response during gear changes by reducing turbo lag. It has been designed to help the turbocharger maintain its rotational speed ready for when you accelerate, whilst also taking the strain away from the impeller. Without removing this stress from your turbo, it could cause premature failure, especially on tuned engines and modified vehicles. Our dump valve kit comes with two different rates of springs to accommodate for stock as well as stage 1 boost settings. We also have additional stage two and above springs available to order through our website depending on your vehicles engines modifications, including hybrid turbo conversions. The Forge Motorsport solution includes all the necessary hardware and step by step instructions for any enthusiast with appropriate garage tools to fit at home within a couple of hours.   In The Box:1 x FMDV35 Valve with Yellow Spring1 x 0.5m of 4mm Vacuum Tube1 x Vacuum Tap3 x Hose Clamps1 x Billet Coupler5 x Cable Ties1 x Uprated Blue Spring1 x Bespoke Silicone Hose   CNC machined billet couplers and components CNC machined twin piston Forge valve The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically Lifetime warranty* Forge valve will not bring on any check engine lights (EML)  Complimentary Products The FMINDK38 is the cold air induction system for Ford’s latest generation 1.5-liter 3-cylinder ST engine. Like with all manufacturers in recent times the need to make smaller engines more efficient and more powerful has been an engineer’s top priority, this then creates a problem for the aftermarket manufacturers to improve what is already fitted to the vehicle, nevertheless this hasn’t stopped us at Forge Motorsport. On a tuned vehicle this combination is an essential purchase as the OEM air box is found to be too restrictive to achieve the optimum power figures and smooth power delivery. This beautifully crafted high flow charge pipe is for the Ford Fiesta ST MK8 and Ford Puma ST. This product has been created over many days and months of dyno testing and road testing to prove the products credentials. The boost pipes are a direct replacement to the original hot-side charge pipe which is rather restrictive especially at the turbo end. FMBP6 was developed to remove these restrictions and now features a smooth and enlarged bore size creating a vast improvement in air flow and a reduction in pressure drop. Our performance inlet pipe for the Ford Fiesta ST MK8 & Puma ST fits between the air filter and turbo inlet pipe and is a highly visible component of the engine bay, accordingly its available in red, blue, grey and black. Its fully compatible with either the OEM filter box or our intake for this application.  

Read more less

The VTA is a performance blow-off valve solution for Fiesta ST180 vehicles with an electronic factory diverter valve.   If you want sound with your performance (or performance with your sound!), GFB’s VTA delivers just that! By combining the proven performance benefits of our ground-breaking DV+ with atmosphere venting, the VTA delivers an aggressive blow-off sound, improved throttle response and boost recovery, as well as superior boost holding and reliability in extreme conditions. The VTA shares the successful DV+ design philosophy: “Keep what works, replace what doesn’t” This means we retain ECU control and the solenoid from the factory diverter to ensure the fastest possible response time, without the added and unnecessary cost of replacing the solenoid like some brands do. The weak part of the factory diverter has always been the plastic valve mechanism – this is the part we replace. The VTA features CNC machined billet components that last a lifetime, and we also change the valve operation method for better performance. The factory diverter valve can only operate in two states – open, or closed. When it opens fully at low boost, or during a partial throttle lift mid-corner, it causes increased lag and a noticeably non-linear boost transition. GFB pioneered the use of “pilot operation” in the DV+, which works by re-purposing the factory solenoid to control the pressure behind the piston rather than the piston itself. This allows the solenoid stroke to be much shorter, speeding up the response time and increasing the actuation force. More importantly, it allows the piston to open and close progressively in response to the amount of boost pressure present, which smooths boost transitions and reduces the lag caused by the factory diverter valve. It is this design philosophy that makes the VTA not only the best performing blow off valve solution, but also the best value on the market.  Key features: TMS Technology for faster boost recovery on gearshift and during throttle modulation Improved boost holding ability Atmosphere venting for blow-off sound Retains ECU control Simple, direct bolt-on kits include everything you need to install Manufactured in Australia in accordance with ISO 9001  VTA or DV+?  Depends if you want sound or not. Both valves are constructed with the same quality materials and valve mechanism, and both offer the same performance and reliability benefits. However, the VTA vents to atmosphere for sound whilst the DV+ recirculates the air to keep it quiet. Why choose a VTA over a “BOV spacer”? “BOV spacers” are cheap and they make sound. But that’s it. All the inherent performance and reliability issues you get with the factory diverter valve remain, because a spacer doesn’t change the diverter valve in any way. The VTA improves the operation of the diverter valve for sound AND performance. Why choose a VTA over a kit that includes a solenoid? Because there’s no performance benefit to replacing the factory solenoid, only a much higher price! If a VTA with the factory solenoid can open in a couple of hundredths of a second, why pay more than you need to?

Read more less

GFB's DV+ diverter valve range offers a direct-fit performance solution for the weak factory diverter valves used on many modern vehicles. By retaining the factory ECU control and recirculating the vented air, the DV+ is a purely performance-orientated product. GFB’s DV+ design solves the longevity and boost leaking issues that are common with factory diverter valves, and also changes the operation method to “pilot actuation” to ensure better performance on stock or modified engines. Furthermore, these benefits won’t cost you the Earth! Rather than throwing the entire factory diverter valve system in the bin (like other manufacturer’s “solutions”), the DV+ keeps what works and replaces what doesn’t. It retains the factory solenoid and ECU control to ensure simple installation and reliable operation. 10% faster opening, 50% faster closing than the factory diverter Retains the factory solenoid for seamless integration Replaces plastic valve parts with metal for reliability and strength on stock or modified engines Direct-fit replacement with GFB’s TMS benefits Exclusive “pilot-actuated” valve mechanism for rapid response at high boost   Related Videos:

Read more less