AIRTEC Front Mount Intercooler Features  1 x twin pass huge 60mm core intercooler with flowed cast end tanks, this means less welding and a stronger intercooler Comes with full fitting guide & pipe work  No cutting bumper with our intercooler kit  Unbeatable value for money Available in Satin Black or Natural Silver AIRTEC 3 year unlimited mileage warranty Fitting will take 1-2 hours depending on mechanical skill   Finished In Pro-Series Satin Black or Natural Silver Proven horizontal 60mm core, runs left to right of the end tanks this gives the single pass design intercooler the shortest route for the charged air to pass though, with such a small turbo, the faster the charged air can get in & out the better. Another great must have with our design is making full use of the hottest part of the intercooler, which is the top section, this is on full show allowing maximum air flow. Tip, more of the grill can be opened up with Dremel or Drill to allow even more air flow to the intercooler, we suggest to do this whilst fitting. Uses original crash bar holes, no drilling or modification required! Please note: Pipework only available in silver Approximate Dimensions: Thickness – 60mm Width – 525mm Height – 378mm Currently sent with Mk7 1.0 Fitting instructions as a fitting guide. Currently does not fit cars with adaptive cruise control.  

Read more less

Is your intercooler looking a bit run down? AIRTEC logo stencil for all AIRTEC intercoolers, freshen up the look of your intercooler. Stencils available for all AIRTEC intercoolers.     Small logo size - (31 x 5cm) Ideal for Mini, Fiesta 1.6 Diesel, 1.0 EcoBoost (Stage 1) Medium logo (44 x 7cm) Ideal for Fiesta MK7 1.0 EcoBoost (Stage 2), Seat Sport, 2.0 TFSI, Astra, Renault Megane. Large logo (61 x 10cm) Ideal for Focus ST 225, Focus RS MK2, Astra VXR (Stage 3) Please note: Stencils are not model specific and can be used on any AIRTEC intercooler.

Read more less

AIRTEC Motorsport front mount intercooler for Fiesta Mk8 ST-200. The perfectly sized intercooler upgrade for standard or stage 1 cars. Rolling road tested at WG Motorworks – As fitted to the AIRTEC demo car. The AIRTEC intercooler features our proven race quality bar and plate core, proven to our perform its lighter weight tune and fin competitor. AIRTEC intercooler features: 1x Huge intercooler with flowed cast end tanks, less welding and a stronger intercooler. Comes complete with full fitting instructions No cutting or drilling required to fit AIRTEC logo’d cast end tanks Proven power increases for fast road & track Available in Pro-Series Black Between 8-12 bhp gains seen on a stage 1 car! Perfect size upgraded intercooler to compliment stage 1 software. Consistent cold side temps on back to back runs seeing just 3-5°C rise compared to stock 15°C+, removing over 140°C from charge temps. Core size std vs AIRTECSTD volume:690 x 135 x 65 = 6L AIRTEC volume:700 x 150 x 80 = 8.4L= 40% bigger than stock! Registered Design Right Number: 6064602

Read more less

EVERYTHING YOU NEEDFOR THE POWER YOU CRAVE PLEASE NOTE: SOFTWARE HAS TO BE INSTALLED BY DEALER! Enhanced power delivery, unique safety features and exhilarating response at your disposal, the Revo Performance Pack delivers much more than peak power figures. Whatever drives you, the Revo Performance Pack has it all. Engineered to perform, only Revo offers a complete tuning solution specifically designed for your vehicle. AIR INTAKE SYSTEM PERFORMANCESOFTWARE INTERCOOLER PIPE UPGRADE KIT INTERCOOLER     OPEN CONEAIR INTAKE SYSTEM Revo Open Cone Systems completely replace the OEM air intake for those who like to announce their vehicle is far from standard. Along with an aggressive intake sound, more air means access to more power throughout the rev-range. IncreasedDiameter DirectFlow PerformanceDesigned Learn more about this product PERFORMANCE ECU SOFTWARE Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev range while maintaining the extensive factory safety mechanisms. Revo Software offers a perfect balance of performance, economy, longevity, and safety so you can drive harder, for longer. OBDII PortInstalled Vehicle HealthCheck Authorised DealerSet-up Read More     INTERCOOLER PIPE UPGRADE The Revo Intercooler Pipe Upgrade kit comes as part of the Revo Intercooler. It reduces charge system resistance and improves flow over the restrictive stock pipework. Featuring fewer restrictions for smoother airflow, and optimised routing, the turbo meets less resistance and can perform more effectively. DirectReplacement IncreasedDiameter DirectInternals Learn more about this product INTERCOOLER UPGRADE The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Unique design features lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software, ensuring you get consistent performance when you need it most. DirectReplacement UniqueFin Design MinimisedPressure Drop Learn more about this product     STOCK POWER200PS TORQUE290NM POWER262PS TORQUE395NM Find your nearest Revo Authorised Dealer Manufacturer Model Variant Engine Year Ford Fiesta Mk8 ST 1.5 EcoBoost 2017 > Images shown are for illustration purposes only All Revo Software availability is ECU ID Dependant. Upgrade pricing for existing Revo Stage 1 ECU customers.  Terms and Conditions apply.  Performance data is taken from 2018 Fiesta ST Mk8. Additional SPS Software Switch purchase required for some software features.  Pricing does not include the installation of parts, please contact your local Revo Authorised Dealer

Read more less

AIRTEC Motorsport Front Mount Intercooler Stage 3 Upgrade for Fiesta Mk8 ST-200 Developed and manufactured at AIRTEC HQ in the UK, we’re proud to launch our Stage 3 front mount intercooler kit with stepped core design suitable for modified Mk8 Fiesta ST owners who want the very highest level of cooling efficiency, power and performance for track or fast road use. Registered Design Right number: 6082519 AIRTEC part no: ATINTFO52 TECHNICAL DATA AIRTEC Motorsport Front Mount Intercooler Stage 3 Upgrade for Fiesta Mk8 ST-200 Developed and manufactured at AIRTEC HQ in the UK, we’re proud to launch our Stage 3 front mount intercooler kit with stepped core design suitable for modified Mk8 Fiesta ST owners who want the very highest level of cooling efficiency, perfect for track or fast road use. Best suited for highly modified vehicles, you will need sufficient software and hardware to make full use of the stage 3 intercooler.   This freer-flowing intercooler features a full size, single-pass core design that covers the full width of the vehicle’s grille area. The stepped core is 80mm in depth in the lower section and 40mm in depth in the upper section that fits neatly in front of the standard crash bar and behind the bumper with no modification required. It therefore offers a huge increase in surface area and volume over standard, and therefore charge temperatures.   The comprehensive kit includes AIRTEC Motorsport’s cast end tanks, laser-cut brackets, silicone hose connectors and all fixtures and fittings for a direct, bolt-on installation.   Its proven cooling efficiency and straight forward fitment makes it an essential modification for all modified Fiesta Mk8 ST models.   AVAILABLE NOW FOR PRE-ORDER! Estimated delivery mid/end January 2020.   AIRTEC intercooler features: 710mm x 415mm x 80/40mm core 60mm & 67mm inlet and outlets Cast end tanks to optimise air flow Larger stepped bar and plate intercooler core Comes complete with full fitting instructions Proven power increases and cooling efficiency Intercooler is now only in satin black Registered Design Right number: 6082519 AIRTEC part no: ATINTFO52

Read more less

Pro Hoses two-piece boost hose kit for Fiesta MK8 ST-200 – With wire insert! To replace the stock intercooler boost hoses. Available in Gloss Black, Performance Blue, Race Red or Orange (Made to order – Please allow 2-4 Weeks)

Read more less

Slotting in between our Stage 1 and Stage 3 solutions, our mid-range intercooler’s size and performance has been increased within the confines of the limited space behind the bumper based upon a core design that is much taller. AIRTEC Part No: ATINTFO60   TECHNICAL DATA As part of our expanding Fiesta Mk8 platform product range, AIRTEC Motorsport is proud to launch our Stage 2 intercooler kit for the ST-200 suitable for track or fast road use. In order to ensure there is no noticeable loss in performance during extended periods of hard driving, we have developed a larger, freer-flowing intercooler that is a direct replacement for the smaller and more restrictive OEM item. Slotting in between our Stage 1 and Stage 3 solutions, our mid-range intercooler’s size and performance has been increased within the confines of the limited space behind the bumper based upon a core design that is much taller. This offers a massive increase in overall capacity in comparison to the original intercooler, as well as a huge increase in frontal area over standard, which allows it to make the most of the air flow provided. Together with our high-flow, moulded one-piece cast end tanks to ensure flow is directed correctly and efficiently, the AIRTEC Motorsport intercooler offers much greater efficiency and volume over standard. Available in a high quality powder coated black finish, the comprehensive kit is a direct replacement and attaches to the original boost pipes and clips. It comes complete with all fixtures and fittings, as well as detailed fitting instructions. TESTED ON TRACKWe tested the Stage 1, 2 and 3 intercoolers back-to-back at Brands Hatch circuit to see how the levels compare with each other. As expected, the Stage 2 offered notably better gains compared to the Stage 1 thanks to its much bigger core, but it could not match the Stage 3’s ability.     Dimensions: OEM intercoolerWidth: 690mm Height: 140mm Depth: 75mm Capacity: 6.3 litres Front area: 966cm² AIRTEC Motorsport IntercoolerWidth: 615mm Height: 390mm Depth: 60mm Capacity: 14.4 litres Front area: 2,340cm² Features: Huge increase in cooling ability Reduced charge temperatures Huge increase in frontal area compared to original intercooler High-flow, moulded one-piece cast end tanks Powder coated black finish All fittings and fixtures included Detailed fitting guide included AIRTEC Part No: ATINTFO60

Read more less

REVO INTERCOOLER FORD FIESTA ST MK8 1.5 ECOBOOST The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, especially. On vehicles with performance software. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 34ºC vs. the Fiesta ST intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks Reinforced Mounting Brackets Intercooler Pipes Included Up to 58% Increased Core Volume Over 34ºC Lower AIT   INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has a 58% larger core volume than the OEM part and offers perfect fitment. By removing the “air separation dam” it allows access to a volume of unused engine bay space to be filled with the intercooler core. INTERCOOLER HEIGHT The decision to manufacturer the cooler at ¾ height and not fill all the available space was key in balancing the performance benefits against functionality. Offering the most efficiency per-cubic-cm cooling capacity and minimising pressure drop, whilst managing unnecessary weight. Also allowing sufficient airflow to the vehicle’s radiator and air ducting.   END TANK DESIGN The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. With a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions. The design has been balanced between core width and optimal tank profile design. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR & PLATE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient airflow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   INTERCOOLER PIPE UPGRADE Supplied with an upgraded silicone charge and throttle pipes. The increased diameter pipework ensures the maximum performance by increasing system volume by over 17%. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components. This has done away with the stock “quick-connect” hose couplings and removes the restrictions present in the charge systems. RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo Stage 1 software, a Revo open cone air intake system and Milltek GPF back exhaust, the Revo Intercooler and pipes were then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling.   PERFORMANCE DATA Showing the last of six consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM Fiesta Mk8 intercooler is highlighted. With peak gains of +10 HP & +28NM Torque, along with increased performance throughout the entire rev range. The stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout. INLET TEMPERATURE This is a metric used to confirm that testing on the Revo Fiesta ST 1.5 EcoBoost Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were hotter on the Revo Intercooler, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERATURE This is the main performance metric to illustrate that the Revo intercooler far exceeds the stock unit. A strong indication that the Revo intercooler is extremely resistant to heat soak and could likely continue for tens more sequential dyno runs before any intake temperature-related issues arose. The graph illustrates the increased cooling performance of the Revo intercooler vs OEM ST intercooler over all six runs. The Revo Intercooler provided a massive 34.4°C max and 12.8°C average intake air temperature reduction across the six back to back full gear dyno runs. INTERCOOLER PRESSURE DROP GRAPH Pressure drop is an important factor when it comes to choosing an Intercooler. The Revo solution features custom cast end tanks to evenly distribute air over the core. This graph highlights that even with massive core size difference there is only a 0.11psi pressure drop in comparison to the stock intercooler, ensuring engine response and minimised turbo lag. You can rest assured that your vehicle will drive and respond as you would expect standard; until you press that pedal!     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Ford Fiesta ST 1.5 EcoBoost 2018 onwards DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo Ford Fiesta MK8 ST Intercooler Instructions NOTES Simple replacement of the OEM part © Revo

Read more less

  AIRTEC Motorsport front mount intercooler for Fiesta Mk8 ST-200. The perfectly sized intercooler upgrade for standard or stage 1 cars. Rolling road tested at WG Motorworks – As fitted to the AIRTEC demo car. The AIRTEC intercooler features our proven race quality bar and plate core, proven to our perform its lighter weight tune and fin competitor. AIRTEC intercooler features: 1x Huge intercooler with flowed cast end tanks, less welding and a stronger intercooler. Comes complete with full fitting instructions No cutting or drilling required to fit AIRTEC logo’d cast end tanks Proven power increases for fast road & track Available in Pro-Series Black Between 8-12 bhp gains seen on a stage 1 car! Perfect size upgraded intercooler to compliment stage 1 software. Consistent cold side temps on back to back runs seeing just 3-5°C rise compared to stock 15°C+, removing over 140°C from charge temps. Core size std vs AIRTECSTD volume:690 x 135 x 65 = 6L AIRTEC volume:700 x 150 x 80 = 8.4L= 40% bigger than stock! Registered Design Right Number: 6064602 AIRTEC part no: ATINTFO42

Read more less

MVT technology designed by Direnza offers greater intercooler efficiency in comparison to other aftermarket alternatives. This is achieved through the use of carefully placed vanes in the end tank which evenly distribute air across the entire core. Ensuring the full surface area of the intercooler core is optimised to cool your charged air, resulting in more power. Test car: Ford Fiesta MK8 ST200 204.4hp / 309.4nmPut through its paces on a state-of-the-art Maha MSR 500 Dyno, our Multi Vane Technology Intercooler for the MK8 ST yielded some highly impressive results. After installing our revolutionary MVT Intercooler, engine performance improved significantly. With the MK8 now producing 210.8hp & 334.2nm of torque, that’s an increase of +6.4hp & 24.8nm of torque without any additional tuning. +6.4 BHP +24.8nm of torque Black coating improves heat dissipation properties Designed using state of the art 3D CAD and CFD modelling Direct replacement for the original Intercooler TIG welded for maximum strength and durability Fitment Ford Fiesta MK8 ST 1.5 Ecoboost 2018+Ford Puma MK2 ST 1.5 Ecoboost 2020+ Core Length (mm) 608 Core Height (mm) 396 Core Width (mm) 56 Overall Length (mm) 1037

Read more less

As part of our expanding Mk8 Fiesta platform product range, AIRTEC Motorsport is proud to launch our additional cold air feed guide for the ST model. During the development of our AIRTEC Motorsport enclosed air box and oil cooler kits, we created an additional comprehensive solution to further improving the car’s cooling ability and reduce air intake temperatures on track or during fast road use. AIRTEC Part No: ATMSFO130 TECHNICAL DATA As part of our expanding Mk8 Fiesta platform product range, AIRTEC Motorsport is proud to launch our additional cold air feed guide for the ST model. During the development of our AIRTEC Motorsport enclosed air box and oil cooler kits, we created an additional comprehensive solution to further improving the car’s cooling ability and reduce air intake temperatures on track or during fast road use. With vast experience in developing uprated cooling packages for a variety of modified track and road cars, the challenge with the Mk8 Fiesta ST was the very limited available space directly behind the open grille area. As a result, we developed an innovative air guide solution to help direct larger volumes of cold air towards the original top air intake feed. The size of the air guides are not only larger than standard but the guide also features a side air duct, utilising the space in the upper right-hand section of the grille area to feed cold air through trunking to either the Enclosed Induction Kit or our soon to be released AIRTEC Motorsport Oil Cooler Kit. Made from aluminium, the kit includes all fixtures and fittings, including instructions, for a simple bolt-on installation. The kit is designed to integrate seamlessly with the car’s existing features and requires no drilling or cutting, so is completely reversible if need be. Its improved cooling efficiency and easy fitment makes it an essential modification for all modified Mk8 ST models. Please note: Fits with any aftermarket intercooler that retains OEM plastic upper surround. This will NOT fit with AIRTEC Motorsport Stage 3  – please see here: AIRTEC  Cold Air Feed for MK8 ST Stage 3 Intercooler Features: Comprehensive kit designed specially for the Mk8 Fiesta ST platform Reduces temperatures on track and road Larger air guides direct more flow towards the original intake Also directs a constant feed of cold air to the air box or oil cooler Reduces temperatures on track and road Designed and developed in the UK No cutting or drilling required to fit Bespoke laser-cut aluminium design High quality powder coated black finish Complete with all fittings and instructions AIRTEC Part No: ATMSFO130

Read more less

COMPETITION INTERCOOLER KIT for Ford Fiesta ST MK8 The WAGNERTUNING high-performance intercooler has got a new competition core (Tube Fin) with the dimensions 620 mm x 390 mm x 56 mm / 24,4 Inch x 15,3 Inch x 2,2 Inch, which was developed especially for the requirements of the Ford Fiesta ST. This high-performance core offers an 150 % larger frontal surface and 86 % more core volume compared to the stock intercooler. The aluminum cast endtanks were designed in CAD and optimized in CFD simulations (for an ideal internal airflow). An incorporated air baffle inside the intercooler inlet ensure a uniform filling of the intercooler. The result is a excellent cooling property with a minimal back pressure. The newly developed competition high-performance core is very light and provides the adjoining components (for example the watercooler) enough air flow. That`s why this kit is perfect for racing use. An optimal cooling effect of the charged air with a significant increase in performance! An anti-corrosion powder coating with perfect heat-conducting properties protects the WAGNERTUNING intercooler from all environmental influences, so a lasting and optimal cooling effect can be guaranteed. The installation is done by replacing the original intercooler and is easy to perform (plug and play). All our products are subject to a continuous quality monitoring. Inlet diameter: Ø67 mm/2,63 Inch (stock click-connection) ; Outlet diameter Ø61 mm/2,4 Inch (stock click-connection) Dimensions stock intercooler:690 mm x 140 mm x 75 mm / 27,2 Inch x 5,5 Inch x 2,9 InchV = 7,25 L / 442,4 Inch³A = 966 cm² / 149,7 Inch² Dimensions WAGNERTUNING intercooler:620 mm x 390 mm x 56 mm / 24,4 Inch x 15,3 Inch x 2,2 InchV = 13,5L / 823,8 Inch³A = 2418 cm² / 374,8 Inch² kit comes with:1 intercooler1 mounting material1 installation instruction

Read more less