Performance - Audi TTS 8S

DQ381 TCU SOFTWARE  Save £200! when you purchase ECU and TCU software together IS38 ALL-WHEEL-DRIVE VEHICLES The DQ381 gearbox was released into Volkswagen AG passenger vehicles back in 2017. The 7-speed dual-clutch gearbox (0GC) was derived from the advanced development of the previous 7-speed gearboxes, such as the DQ380 (ODE) and DQ500 (0BT), which had been used in commercial vehicles from 2010 and passenger vehicles since 2011. One key feature of the DQ381 gearbox was principally aimed at increasing efficiency. Unlike the DQ380 gearbox, the DQ381 was designed to be used in both FWD and all-wheel drive vehicles on the MQB chassis platform, such as the Mk7 Golf  R, Audi S3, SQ2 and Cupra Ateca.  This 7-speed wet clutch gearbox is already an improvement over the previous DQ250 6-speed, in terms of allowing the vehicle to shift more efficiently, and with a smother gearchange due to the closer gear ratios. However, driving a DQ381 equipped vehicle you will know that there are still areas that can be improved, especially on performance modes. With the stock calibration, you may find that gear shifts happen too low in the RPM range, or too high when in sports mode. These can lead to unsmooth driving, or make the vehicle feel too aggressive. You may have also experienced clutch slip when running performance ECU Software. IT'S ALL ABOUT THE DRIVE. Revo DQ381 TCU software has been designed for the driven. Working on the characteristics of the gearbox to provide a better driving experience and optimal performance when coupled with our performance ECU software. Holding the gears better in sports mode so it’s not changing up early and allows the engine to be in the right power band more of the time. Revo TCU Software gives you much more than just increased clamping pressure and quicker shifts. A large part of development is based on driving scenarios and feedback, ensuring an exhilarating experience. Expect smooth and refined response at low RPM & partial throttle, with optimal shift programming for wide-open throttle driving.   SOFTWARE FEATURES FASTER SHIFTING Shift times are reduced in auto and manual modes. INCREASED LAUNCH COUNTER The stock launch limit has been raised. INCREASED CLUTCH PRESSURE Maximum clutch pressure is raised to prevent slip. INCREASED CLUTCH TORQUE LIMITS Torque limits are raised to allow to run higher torque levels. OPTIMISED SHIFTING Shift strategy now matches our ECU Software. 3 STEP LAUNCH CONTROL Launch at 3 different points based on throttle position. PROGRESSIVE SOFTWARE The software works with stage 1-3 ECU Software. OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port. MONEY BACK GUARANTEE If not 100% satisfied, we'll give you your money back.     GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU & TCU software.   KEY FEATURES DRIVEABILITY Revo TCU software has been designed alongside our ECU software to not only improve performance but to enhance the feel and driveability of your vehicle. This was the key focus during development, and something that takes time and thousands of miles to achieve. When vehicles are equipped with an Eco/Efficiency drive mode, this uses unique mapping and remains as “stock” to keep all the characteristics. To ensure low RPM driveability, whilst in traffic for example, when you are below 30% throttle input the software will replicate the feel of the stock software. But when required, put the car in Sport/Cupra drive modes, and the gearbox in Drive or Sport and you will be treated to a much-improved sportier feel. PROGRESSIVE SOFTWARE As we produce all our ECU and TCU software in house and have access to vehicles through our global network of authorised Dealers, we have been able to test and refine the software for all ECU stages. This means that our “Progressive TCU” software will work with Stage1 to Stage 3 ECU software on 2.0 TSI DQ381 vehicles. You can install Revo TCU software when at Stage 1 ECU, and it will cover you as you progress through the ECU stages without the need to change TCU software. SHIFTING Gearshift points in gearbox D and S modes have been enhanced and matched with Revo ECU Software. Meaning each gear shift will be at the optimal point to give the best possible performance and fastest acceleration. The shifting times have also been improved and made quicker in D, S and S manual modes. Tested on Stage 2 Audi S3 8V we saw an improvement of up to 0.4s on the 0-60mph time from launch over the stock TCU calibration. The 3-step launch control RPM limits have been optimised to offer 3 different RPM points depending on the throttle input 10-30% launches at 2200rpm, 45-79% launches at 3600rpm and over 80% launches at 4250rpm. When at partial throttle, the gearbox isn’t always looking for the highest gear, it holds the current gear longer. Keeping the turbo spooled and the vehicle within the right power band, thus not changing up and down the gears at much and therefore offering a smoother and more enjoyable drive. Notes: All Revo Software availability is TCU ID Dependant. Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

REVO RF0 WHEEL LIGHTWEIGHT. STRONG. FLOW FORMED.  OVERVIEW The RF0 wheel is a flow-formed alloy that's lightweight yet exceptionally strong, designed in-house at Revo HQ in the UK. Flow forming is one of the most advanced manufacturing technologies to enter the wheel industry. Flow Forming Technology involves the application of pressure to the inner barrel of the wheel while spinning and after it has been cast. This process stretches and compresses the aluminium, which increases tensile strength. In this respect, the process shares similar properties to those found in the forging process. The final product is lighter, stronger, has increased elongation, and much greater shock resistance as well as an increased load capacity over regular cast wheels. Whilst the RF0 wheel shares a similar design concept to our previous generation RV0, the more advanced manufacturing process offered through flow forming allows for more definition in the design, particularly noticeable in the spokes and rim edge fillets. By reducing the weight of your wheels 'unsprung weight' your suspension starts to have a much easier time. Each bump can be controlled more quickly and easily. This helps keep your tyre in contact with the road for longer, which is obviously great news for car control and braking. Reducing the 'rotational mass has its benefits too. A classic/timeless motorsport look featuring an embossed Revo logo and branded centre cap to compliment the subtle styling. Available in a choice of Hyper Silver, Gloss Black, Matte Bronze & Matte Anthracite. BENEFITS Flow formed manufactured Lightweight under 12kg Fits Revo big brake kit* COLOUR OPTIONS Gloss Black Matte Bronze Matte Anthracite Hyper Silver   FITTING  RF020 Wheel 20 x 8.5j, 5 x 112, ET45, CB 66.6mm – The below fitments will require a 66.6mm to 57.mm spigot ring which is included with this wheel size. Manufacturer Model Variant Year Audi A3 / S3 / RS3  All 2012 > Audi TT / TTS /TT RS All 2014 > Audi A4/A5/A6/A7 5 All 2007 > Seat Leon All 2012 > Skoda Octavia All 2014 > VW Golf All 2014 > VW Golf GTI / R All 2014 > VW Beetle All 2011 > VW Caddy All 2003 > VW Passat All 2015 > VW Tiguan All 2016 >   REVO BIG BRAKE KIT The RF020 wheels were also designed to fit with all Revo brake kits without the need for spacers.     Notes: The fitment table above is a guide, please check your individual vehicle for correct fitment. When using the RF0 wheels on track it is advised that you remove the centre caps from the wheel to avoid distortion due to excessive heat transfer Price includes x1 RF020 wheel, Tyres not included. Before installation of any wheels please ensure that you have the correct bolt fitment with the correct seating radius. Failure to do so could result in poor fitment and potential damage to your wheels. No Spigot ring is needed for this vehicle.  Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Overview The Revo Carbon Air Scoop is designed to work in harmony with Revo software to unleash the maximum potential from your engine. Flow testing of the OEM intake emphasised the restrictions in the system, giving the Revo engineers a clear indication of what needed improving. The stock front panel used to direct air to the airbox, the standard air filter and convolutions in the rear pipe from the airbox to turbo were found to be the main ‘choking points’ in the system. The Revo system is a direct replacement kit and includes a beautiful carbon front panel, designed to direct cold air directly to the OEM airbox utilising an internal fin, along with the second feed of cold air into the engine bay to help keep ambient temperatures lower. A coolant relocation hose is also included. BENEFITS Improved Performance Carbon Series Quality Less Restriction Direct Replacement Kit   CARBON AIR SCOOP CARBON AIR SCOOP The Revo carbon front section integrates a direct cold air feed which is blanked off on the standard part, and also includes an internal fin that directs air towards the airbox. Designed to also aid in lowering ambient engine temperatures, the Revo engineering team have integrated a second air inlet to allow a direct cold air feed to the engine bay. MORE AIR FLOW Manufactured using the highest quality materials, the Revo carbon front section directly replaces the standard plastic part. A high gloss carbon finish coupled with impressive performance benefits offers a product that delivers in form and function, looking great in the engine bay yet still performing above and beyond the OEM part.   RELOCATION HOSE The Revo Coolant Relocation Hose offers a high-quality single piece replacement for the OEM part which redirects the hose under the front air scoop to give a more aesthetically pleasing look.   TESTING MORE AIR, LESS RESTRICTION Testing was carried out with consistent conditions on both the OEM intake and the Revo Carbon Air Scoop with ProPanel filter, replacement silicone hose, and stock turbo inlet elbow. The graphs below were produced with products fitted to a vehicle and also in a standalone test off the car. The Revo system was tested on a flow bench to highlight the efficiency of the kit in allowing more air to reach the turbo, quickly and with less restriction. The OEM system reached its maximum potential of 440 cubic feet per minute, compared to the Revo system which was able to flow 480 CFM with a restriction of around 600 mmWg. This difference allows the engine to still make power at the top of the rev installing with the Revo kit.   INCREASED POWER AND TORQUE The Carbon Air Scoop (with silicone back hose and ProPanel) was installed on a variety of stage 2 & 3 vehicles, all tested on a 4-wheel hub dyno. Three consecutive runs were carried out on each vehicle comparing the stock system to the Revo MQB Carbon Air Scoop. A consistent gain of +10WHP was found on the 300ps 2.0TSI and +17WHP on the 220ps 2.0TSI, with both giving an average gain throughout the rev range of +16NM torque. It was also noted that with the greater flow of air the turbo was able to spool a lot more quickly giving enhanced throttle response.   FITMENT   Manufacturer Model Engine Year Audi S3 (8v) 2.0 TFSI 12 - Audi TT 2.0 TFSI 15 - Audi TTS 2.0 TFSI 15 - Audi A3 (8v) 1.8 / 2.0 TFSI 12 - Seat Leon Mk3 1.8 / 2.0 TSI 12 - Skoda Octavia Mk3 1.8 / 2.0 TSI 12 - Skoda Superb Mk3 2.0 TSI 15 - VW Golf MK7 2.0 TSI (GTi/R) 12 -   Revo Carbon Series air intake systems perform beautifully. Designed to function no matter the power, Carbon Series intakes look great because of their effective design. Click to find out more   Notes: Simple replacement of the OEM part Please contact your local Revo Authorised Dealer for additional information and availability. 

Read more less

REVO ENGINE MOUNTS More power results in more movement during aggressive acceleration. The stock engine mounts, designed to favour comfort over performance, fail to manage axle hop and torque effectively requiring you to ease off to gain traction. Designed to significantly reduce this engine movement, Revo engine mounts use Powerflex bushings to minimise noise, vibration and harshness levels (NVH) while drastically improving traction and acceleration. The engine, transmission and torque mounts have been CAD designed to offer OE quality fitment with the performance benefits and quality of a Revo product. KEY FEATURES Dramatically reduce engine movement Improved acceleration and torque Powerflex polyurethane bushings Comes with a removal tool for torque mount   ENGINE & TRANSMISSION MOUNT The primary design goal of the engine and transmission mounts was to provide a management system for engine movement during vehicle operation with increased power/torque, to retain vehicle acceleration and tyre contact during aggressive driving. The aforementioned solution must also continue to dissipate the NVH naturally created by the drivetrain. To accomplish this, the bushing design of past Revo engine mounts was retained in the MQB engine and transmission mounts, allowing Revo engineers to focus their efforts on bushing stiffness/type to accomplish the task. TORQUE MOUNT Arguably the most vital engine mount upgrade to consider, testing highlighted that the engines stock lower torque mount allowed a substantial amount of engine movement to occur. Although some improvements were noted during testing of an insert style upgrade designed to stiffen the standard mount, there was a significant increase in NVH felt in the cabin. This was dramatically reduced when completely replaced with the Revo polyurethane torque mount and also improved acceleration. Fitting the mount does not require the sub-frame to be removed, reducing installation time and the need for axle re-alignment. A Revo installation tool is included to make removal of the OEM mount and installation of the replacement as quick and easy as possible.   MATERIALS, MANUFACTURING & FITMENT Effective design and fitment play a principal role in managing engine movement to ensure optimal acceleration and tyre contact with the road while dissipating NVH experienced from the drivetrain. Each component has been designed using CAD technology to ensure precise fitment and is supplied with class 12.9 hardware to replace the standard fixings. To ensure optimum strength and durability, brackets and housings are CNC machined from 6061-billet aluminium and finished with an anodised coating to protect from heat and corrosion. POWERFLEX BUSHINGS Powerflex utilises a unique formula of polyurethane, custom-designed to ensure optimum fitment in the machined housings. After testing various amounts of compliance, our engineers were able to fine-tune the final bush to achieve a balance between performance and comfort. Polyurethane is also resistant to oil, fuel unlike the rubber used in the OEM mount which can lead to perishing and failure. Our specified durometers provide a stiffer mount to limit the engine movement without compromising on NVH (Noise Vibration Harshness) levels in the process.     OEM COMFORT, AFTERMARKET PERFORMANCE To achieve the optimal balance between performance and comfort, several different durometer bushings were tested on a Volkswagen Golf Mk7 GTI. Bushings were systematically tested at precise increments at each mount location. A 3-axis accelerometer was used to quantify the NVH levels being transmitted into the cabin, as well as the acceleration of the drivetrain during loading. Accelerometer data gave us a way to compare mount combinations against each other with a low data error percentage and to quantify driver comfort as well as engine movement. Supplemental data was taken from VCDS to ensure each test was standardised over a given throttle, RPM and speed range. The graph shows the amount of vibration measured whilst driving through the gears.         VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi A3 8V 2.0 TSI 2012 onwards Audi S3 8V 2.0 TSI 2012 onwards Audi TT MK3 2.0 TSI 2014 onwards Audi TTS MK3 2.0 TSI 2014 onwards Seat Leon MK3 2.0 TSI 2012 onwards Skoda Octavia 2.0 TSI 2013 onwards VW Golf GTi 2.0 TSI 2012 onwards VW Golf R 2.0 TSI 2012 onwards   Notes: Simple replacement of the OEM part Lower torque mount kit includes torque mount and Installation Tool The full kit includes engine mount, transmission mount, torque mount and torque mount installation tool Performance Engines mounts will produce more vibrations at low RPM then softer OEM Mounts. Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

TURBO INLET HOSE The Revo Machined Turbo Inlet has been designed and engineered to directly replace the stock elbow or the IS38 Revo Machined Turbo Inlet when fitting the Revo IS38ETR Enhanced Turbo Upgrade. The Machined Turbo Inlet has been designed to match the inlet diameter of the Revo IS38ETR turbo to allow for a smoother uninterrupted airflow transition between components.  Can be used with the Revo 2.0 TSI Turbo inlet hose or with the Revo Carbon Series Airbox lid and 100mm Silicone Turbo Inlet Hose.   KEY FEATURES Machined from a single piece of billet Aluminium  Smooth Taper Matched Internal diameter Smooth and increased airflow MACHINED TURBO INLET The Revo machined inlet replaces the restrictive plastic OEM inlet elbow. The machined billet aluminium inlet securely fits the IS38ETR using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence.     Notes: Designed to be used with Revo Inlet hoses Please contact your local Revo Authorised Dealer for additional information and availability. © Revo

Read more less

REVO CARBON SERIES - AIR BOX LID The Revo Carbon Lid and turbo inlet hose have been designed and engineered to directly replace the stock airbox lid, pipe and elbow found in vehicles with the 1.8 and 2.0 TSI engines with an IHI turbo. The Revo Carbon Lid offers a high-quality replacement, with its contoured design it not only just aesthetically pleasing but designed to improve airflow and performance of your vehicle. KEY FEATURES Increased performance & airflow Carbon Series Quality Engineered for both LHD and RHD fitment 16% Larger airbox outlet OEM VS CARBON INTAKE With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running Revo Software. The Revo Carbon Lid has been designed to increase airbox volume and promote smoother airflow. The closed air system helps eliminate heat soak whilst directing cold air through its curved design directly to the oversized outlet. With a 16% larger outlet, the Carbon Lid drastically improves the rate at which air can flow, ensuring maximum performance at even Stage 3 specification.   SILICONE HOSE DESIGN The Revo Turbo Hose as an increased inner diameter to match the large carbon lid outlet that then gradually tapers to the turbo to optimise airflow, while maintaining the tolerances required to fit both LHD and RHD vehicles. Designed to replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range. TURBO INLET The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The billet aluminium piece securely fits the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components ensures smooth and linear airflow transition between elements, providing uninterrupted airflow and removing any unnecessary turbulence.     RESEARCH AND DEVELOPMENT All Revo products are designed and rigorously tested in-house utilising 3D printed prototypes, latest CAD and CFD programs, 4 wheel hub dyno and Revo developed data acquisition software. The Revo Carbon lid and Turbo Inlet Hose allows the Stock IS38/IS20 turbo to run more efficiently, by maximising air volume and minimising turbulence you increase power and torque, especially at the top end of the rev range as highlighted during controlled Dyno testing.  Read more     GRAPHS   FITMENT   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V)/td> 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Volkswagen Golf (MK7) 2.0 TSI GTI 12 - Volkswagen Golf (MK7) 2.0 TSI R 12 - Volkswagen Golf (MK7) 1.8 TSI 12 -  

Read more less

TURBO INLET HOSE The Revo Turbo Inlet Hose has been designed and engineered to directly replace the stock pipe and elbow found in vehicles with the 1.8 and 2.0 TSI engines with an IHI turbo. The Revo Turbo Inlet Hose offers a high-quality single piece replacement for the OEM parts which allows for smoother uninterrupted airflow, improving the throttle response and performance of your vehicle. KEY FEATURES Increased performance Improves airflow efficiency Constant taper for smoother flow Turbo matched inlets Replaces restrictive stock turbo elbow Engineered for both LHD and RHD fitment OEM PART With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running Revo Software. With a generously sized airbox, the standard plastic intake hose causes the most amount of restriction; convolutions designed to allow for engine movement disrupt airflow, a small internal diameter limits the volume of air and a sharp reduction in hose diameter at the turbo causes turbulence.   TURBO INLET The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The machined billet aluminium inlet securely fits the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence.   SILICONE HOSE DESIGN The Revo Turbo Hose as an increased inner diameter that gradually tapers from airbox to turbo to optimise airflow, while maintaining the tolerances required to fit both LHD and RHD vehicles with a standard airbox. Designed to directly replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range.   A four-ply construction with an internal wire helix increases strength to prevent collapsing under pressure. Internal steps flush fit against the stock airbox and the machined inlet, creating a smooth transition between components ensuring the smoothest airflow possible to the turbo. A machined bung is integrated into the hose, connecting the stock PCV system vacuum.       RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested. The Revo Turbo Inlet Hose allows the Stock IS38 turbo to run more efficiently, intake a larger volume of air and minimise turbulence. This increases power and torque, especially at the top end of the rev range as highlighted during controlled Dyno testing.   GRAPHS DATA Up to 12WHP and 15NM gains Graphs produced with Revo stage 2 software on Audi S3 8V Stock Runs with complete OEM Air intake setup Revo Runs with Revo Intake Hose and ProPanel Filter   VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V) 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Volkswagen Golf (MK7) R 2.0 TSI 12 - Volkswagen Golf (MK7) GTI 2.0 TSI 12 - Volkswagen Golf (MK7) 1.8 TSI 12 - Volkswagen Passat 2.0 TSI 15 -  

Read more less

The Revo Big Brake Kit comes complete with everything required to upgrade your stopping power. With Calipers and discs manufactured by industry leaders Alcon® and a floating system designed by our in-house engineers, each kit includes everything you need in one box; brake lines, brake pads, floating discs, mono-bloc calipers, brackets and even brake fluid. Revo Big Brake Kit UpgradeImproves stopping power under any condition OVERVIEW The Revo Big Brake Kit Upgrade is engineered to improve your stopping power in any condition. Whilst stock brakes are perfectly adequate for general driving; the braking system is often overlooked when enhancing a vehicles performance. The Revo brake kit is made by world leading brake manufacturer Alcon; utilising over 30years of motorsport braking innovation only the best materials, techniques and processes have been used. In-depth testing is a key factor in the development of our products; our brake kits have been aggressively tested in a variety of conditions in both road and track scenarios to ensure they meet the constant high stress of track days, sprints and fast road driving. Test kits were installed on our in-house development vehicles along with a number of vehicles around the world and put through their paces to prove their worth over the stock setup; providing exceptional performance combined with consistency and durability you can rely on, corner after corner, stop after stop. Made by world leading brake manufacturer Alcon, only the best materials, techniques and processes have been used, with every step of the manufacturing process completed in the UK. Alcon has been at the forefront of motorsport braking innovation for over 30 years. BENEFITS Low Rotational Mass Improved Pedal Responsiveness Lower Long-term Maintenance Costs Superior Heat Dissipation: Less Prone To Fade Increased Braking Performance On & Off Track 100 - 0 MPH AVERAGE STOPPING DISTANCE CALIPERS Our lightweight six pot caliper is a single piece aluminium Mono-bloc design. This design has been used to maximise rigidity, pedal feel and overall braking performance. The caliper incorporates a progressive six piston setup to give great brake balance, and high quality seals increasing resilience to road salts and other corrosive elements. DISCS We use a two-piece floating disc and hat design to efficiently dissipate heat. The friction surface features crescent groves designed to increase bite and remove debris from the pad surface giving the perfect balance between brake feel and longevity. The discs feature internal cooling vanes that draw air from the center of the disc outward to maximise heat dissipation and minimise heat transfer to the calipers, pads, and brake fluid, which plays an all important part in providing consistent stopping power for your vehicle. BRAKE PADS We supply our brake kit with Ferodo DS Performance Pads that offer a consistent pedal feel and fantastic braking performance both from cold and when hot. Combined with low wheel dusting, minimal noise characteristics, and low disc and pad wear rates this is the ideal pad compound for general road and track driving. BRAKE LINES Our brake kit is supplied with stainless lines; consisting of a PTFE inner and stainless steel braided outer to eliminate the spongy feel of original rubber hoses, provide superior resistance to corrosion, and offer consistent braking performance. BRAKE FLUID Our brakes are supplied with Motul Dot 5.1 brake fluid; specifically designed for brakes systems with ABS. This is a long life synthetic brake fluid with superior boiling point qualities to conventional Dot 3 and 4 spec. fluids. KIT CONTENTS Revo by Alcon Caliper x2 (3.3 Kg Each) Revo by Alcon Discs x2 (7.66 Kg Each) 6061 Aluminium Anodised Bell x2 6061 Aluminium Anodised Caliper Bracket Revo Stainless Steel Braided Brake Lines Motul Dot 5.1 Brake Fluid Ferodo DS Performance Brake Pads     TECHNICAL DOCUMENTS The following documents are available to view: BIG BRAKE KIT FITTING Download the Revo Big Brake Fitting Instructions BEDDING IN Download the Revo Big Brake Bedding in procedure FITTING TEMPLATE Download the Revo Big Brake Printable 355mm Disc Template. See if the Big Brake kits will fit inside your wheels. FITTING TEMPLATE Download the Revo Big Brake Printable 380mm Disc Template. See if the Big Brake kits will fit inside your wheels.     FITTING      Manufacturer Model Engine Year Audi A3 (8v) All 12 - Seat Leon MK3 (5F) All 12 - Skoda Octavia Mk3 (5E) All 13 - VW Golf MK7 All 12 -  

Read more less

Only The Driven know that the cooler the air, the more power produced. Revo Intercoolers drastically improve your vehicles ability to cool air compressed by the turbo. Increased volume and surface area, bar and plate cores with end tanks specifically designed to promote even airflow all play a part in lowering temperatures; without negatively affecting pressure. REVO AIR INTERCOOLER MQB 1.8/2.0 TSI EA888 GEN3 The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 36ºC vs. the MQB Golf R intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment Up to 51% Increased Core Volume Over 36ºC Lower AIT INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has much larger core volume than the OEM part and offers perfect fitment, improving cooling by utilising the full volume of the stock location space as well as cold ambient air from the front of the vehicle. END TANK DESIGN The stock end tanks are inefficiently designed and create turbulent air in corners. These sections create a natural flow distribution but slow charge air and increase pressure drop. The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions from turbulent air pockets found in the OE intercooler. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR AND PLATE CORE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient air flow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   SILICONE HOSES Supplied with stronger oil resistant silicone hoses, the Revo Intercooler can be installed using the stock pipework or recommended Revo Intercooler pipework. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components.   BRACKETS To ensures precision fitment, Only Revo offers a CNC machined bracket system. Produced to a superior tolerance than that of a cast mounting system, this unique feature also ensures that the supporting brackets are strong and less prone to failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout of the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo Stage 2 software, a Revo air intake system and Milltek downpipe, the Revo Intercooler was then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA Golf GTI with Revo Stage 2 Software, Golf R intercooler and Carbon Series Front Scoop Showing the last of five consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM Golf R intercooler is highlighted. With max gains of +10 HP & +20NM Torque, along with increased performance throughout the entire rev range, the stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, losing just 2% peak power over the 5 runs compared to 5% on the stock cooler. INLET TEMPERATURE This is a metric used to confirm that testing on the Revo MQB Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were hotter on the Revo Intercooler, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERETURE This graph illustrates the increased cooling performance of the Revo intercooler vs OEM Golf R intercooler over all five runs. The Revo Intercooler keeps temperatures below 49ºC on the fifth run, lower than the stock on its first at 58ºC.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi A3 8V 1.8 / 2.0TSI 2012 > Audi S3 8V 2.0TSI 2012 > Audi TT / TTS 2.0TSI 2015 > Seat Leon 1.8 / 2.0TSI 2013 > Skoda Octavia 1.8 / 2.0TSI 2013 > Skoda Superb 1.8 / 2.0TSI 2015 > VW Golf Mk7 / Alltrack / Sportwagen 1.8 / 2.0TSI 2013 > VW Golf Mk7 GTI / R 2.0TSI 2014 > VW Passat 1.8 / 2.0TSI 2015 > VW Tiguan 2.0TSI 2016 > VW Touran 2.0TSI 2016 > DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo MQB Golf / Octavia / Leon Intercooler Instructions FITTING INSTRUCTIONS Download the Revo MQB A3 / S3 Intercooler Instructions NOTES Simple replacement of the OEM part Also available for the Golf Mk5/6 MLB Platform Will not fit on cars with O2 sensors fitted without interference on the sensor. It is recommended to speak with your dealer before if you are unsure.

Read more less