Revo Hardware

Revo 1.8 TSI OEM+ System Increased Power, Torque & Throttle Response Overview The new 1.8 TSI intake has been designed to work in harmony with our Revo software. Starting by looking at the OE system we set about deciding where we could improve on the current design, it was apparent from the outset that the factory airbox was more than substantial for the flow of air the car required. The stock airbox is actually about 15% larger than the airbox on the MK7 Golf Gti. So we decided to keep with the airbox on this basis and had one of the Revo  ProPanel filters designed to replace the restrictive OE paper element to allow the turbo to breathe easier. The next section of the factory intake was the OE intake hose which feeds the clean air from the airbox into the turbo. The stock hose is made out of plastic with multiple ridges in it to allow for flex of the intake system under load, however having these ridges causes a lot or turbulence to the air. We re-designed the hose to eradicate this, maintaining the precise OE fit whilst eradicating any turbulence issues. Working alongside SamcoSport ensured the highest quality product, we opted to use high temperature nomex fabric to withstand the heat from the turbo, and automotive grade silicone rubber to avoid fading or perishing over time. The inner ridges made way for smooth inner walls which after testing increased both airflow and speed resulting in more power and flow. To avoid the all too common problem of hose collapse under negative pressure from the turbo, we incorporated an embedded wire helix to prevent this from happening, no matter how much more power you run.   Benefits OEM+ Look New silicone Samco hose to mimic OE whilst eliminating turbulence Increased airflow and speed resualting in better power Optimum performance working in harmony with Revo Software Consistent gains and reduction in restriction + 8WHP Power and + 8NM Torque gains (Audi S1) Kit INCLUDES Revo ProPanel Filter Revo by Samco Intake hose 2 x Hose Clamps (Air box not included)   More Air, Less Restriction Testing was carried out in various ways, dyno, flow and road. On the flow testing we set up the stock system on a flow test bed, The ISO5011 performance test, measures the restriction (measured in mm WG) created by the air filter and any equipment used in the air intake at multiple air flow rates (measured in CFM). The test uses a flow bench to draw air through the air intake at a given flow rate. The flow rate is calculated by measuring the pressure difference using a manometer across a set orifice. A second manometer is used to measure the depression or vacuum created by the air intake. The lower the vacuum created by the air intake the better it has performed in the test. Each component of the system was measured, analysed and improved to enable us to maximise the performance of the intake. The results were great and the complete Revo intake system compared to the full stock OE system showed a 19% reduction in restriction at 400CFM.     Revo S1 Intake Torque Graph Revo S1 intake Power Graph Air Flow Chart   *Dyno testing was carried out on our Dynopak 4 wheel drive dyno and on back to back dyno runs we saw consistent gains between 5-8 WHP and 8NM Torque (Audi S1 Test)      Technical Documents The following documents are available to view: Fitting Instructions Download the RA831M600100 Revo Audi 1.8 TSI OEM+ Intake Fitting Instructions Fitment      Manufacturer Model Engine Year Seat Ibiza Cupra 1.8 TSI 2015 > VW Polo GTi 1.8 TSI 2015 >

Read more less

Revo Intercooler Pipe Upgrade Ford Focus RS 2.3 EcoBoost The Revo Intercooler Pipe Upgrade kit increases power and reduces lag by replacing the restrictive stock pipework. Designed for the Ford Focus RS 2.3 EcoBoost, this upgrade features a larger internal diameter, less restrictions and removes the sound suppressor chamber. This means the turbo meets less resistance and can perform more effectively at any level of tuning. A multitude of design features and attention to detail that Only Revo offer means this a product that not only looks great but more importantly performs. Thicker reinforced oil resistant silicone hoses, lightweight mandrel bent aluminium pipework, flush fit joins to eliminate turbulence and is designed to fit either the stock or Revo Intercooler. Key Features Increased internal diameter Smoother airflow Wire reinforced Silicone hoses Increased performance   Research and Development All Revo products are designed in-house and are rigorously tested. By utilising the latest 3D printing technology, the latest CAD and CFD programs, hub dyno and Revo data acquisition software we are able to ensure our products meet the high expectations of Only The Driven. The Revo carbon intake allows the RS turbo to run more efficiently, intake a larger volume of air and minimise turbulence. This increases power and torque, especially at the top end of the rev range as highlighted during controlled dyno testing. Performance Data On the Revo Ford Focus RS Stage 2 Performance Package, the Revo intercooler pipe upgrade gave a healthy gain of more than 11whp and 20NM at 3900RPM over the stock parts with a constant gain throughout the rev range especially noticeable in the mid to high range.

Read more less