Performance - Dodge Neon SRT -4

Now you can fine tune your Blow Off/Diverter Valve to the exact needs of your engine with this complete tuning kit. If you are finding that the valve is dumping more than required, or if you are losing boost pressure it is normally an indication that a stronger spring is required. Alternatively, if the valve is failing to dump it may be necessary to install a weaker spring. Please note that fitting a stronger spring into a valve will not increase boost pressure, unless existing pressure is being lost. Failure to allow the valve to operate by installing a spring which is too strong, may cause damage to the turbocharger. Please also note that the red coded springs should not be installed in the DVR or DV007 diaphragm valves.  Valve Spring color coding: Green - 5-15 PSI, Yellow - 15-23 PSI, Blue - 23-30 PSI, Red - 30 + PSI.*The above figures are estimates only and should only be considered as a guideline* Note: Serious or fatal damage may occur to the engine and associated components if this product is incorrectly matched to the individual engine requirements. Forge Motorsport nor any of it’s authorised distributors can assume any responsibility for any adverse effects resulting from the installation of this product.  Please contact us if you are uncertain whether this kit is suitable for your valve. *Please Note - The colours of the springs illustrated may differ to what you receive. All spring kits are brand new but are not sprayed. Colour is used as an identifier*   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   FOR MULTIPLE VEHICLES 

Read more less

Blow Off Valve for Hyundai Genesis Sonata and Kia Sportage and Optima. The Forge direct replacement blow-off valve is designed to be a more durable and performance oriented valve than the OEM unit. The OEM valve is suitable for stock boost levels for a period of time, however, once boost pressure is raised, and after prolonged use, the stock valve will no longer be adequate. Raising the boost output of the vehicle will have a number of effects on the OEM valve. First and foremost, the additional boost pressure will quickly exceed the capacity of the OEM spring to keep the valve closed under higher boost levels. Since you cannot change the springs in the OEM valve, it cannot be adjusted for higher boost levels. Secondly, the additional heat generated by the increased boost will quickly deteriorate the OEM rubber valve diaphragm, which will also lose strength with repeated oscillations. The Forge valve uses full billet aluminum construction and Viton silicone o-rings that will withstand the highest boost levels and repeated abuse. It is also tunable for varying boost levels with the included spring tuning kit. If there is ever a problem with the valve such as a torn o-ring, replacements are available free of charge, and the valve is fully rebuildable. As the Genesis Coupe 2.0T does not use a MAF (mass air flow) sensor, there is no reason that the residual boost pressure at throttle lift cannot be vented to the atmosphere such as with this valve. The engine management does not meter the air volume entering the engine, so this residual pressure can be discharged without any adverse affects on the performance or driveability of the vehicle. Additionally, the valve being open at an idle or vacuum condition is a normal occurance, and is not indicative of a leaking valve. If the intake manifold is in vacuum, even while cruising at speed, the valve may be open. The OEM valve operates in this same manner, however, it is just not visible/audible because it is recirculating instead of vented to the atmosphere. Using a stiffer spring to keep the valve closed at a vacuum condition may result in too stiff of a spring tension to effectively discharge pressure at a throttle lift condition.   In The Box:1 x FMDVHGA Valve1 x Uprated Yellow Spring1 x Uprated Blue Spring3 x M6 x 16 Socket Cap Bolts3 x M6 Plain Washers3 x M6 Spring Washers1 x Forge Sticker If you wish to tune this product to fit the needs of your engine, please see the spring tuning kit below.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This has been designed by Forge Motorsport as a direct replacement for the compressor bypass valve (CBV) that bolts directly to the turbo . It replaces the OEM diaphragm type valve with a piston design that allows for tuning with interchangable springs. For those running higher boost pressures after software tuning this really is a must to ensure that you do not lose boost through the valve.    In The Box:1 x FMDVRMR Valve1 x Uprated Yellow Spring1 x Uprated Blue Spring3 x M6 x 16 Socket Cap Bolts1 x Forge Sticker This product comes assembled with a green spring but is supplied with an additional uprated yellow spring. If your car is a Renault Megane RS250, 265, or 275, then this spring should be fitted instead of the stock green spring. If you wish to further tune this product to fit the needs of your engine, please see the spring tuning kit below.  Replaces OEM Part No. 55558627 (Saab) If you are unsure if this product is suitable for your application, please contact us.    Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This product is built with a predetermined actuator spring suitable for at, or slightly above factory boost levels. The actuator can be assembled with a stiffer spring upon request. Please contact us directly concerning this process It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket. Forge Motorsport nor any of it’s authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. After requests for a very durable, fit and forget version of our actuators that would withstand the rigors of marine corrosion or simply would not tarnish, we have now added the option of ordering any of our piston design actuators with stainless steel bodies and external components/fixings. This option does incur a surcharge and will be shown when added to your basket. Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Please contact us by email if you require more information. In The Box:1 x FMNEONACT Actuator1 x Forge Sticker This actuator is built with a Blue coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Piston option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less