Performance - Golf MK7

K&N's replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration. We make over 1,200 different replacement air filters for the majority of vehicles on the road. These filters are washable and reusable and are custom designed to fit into your existing factory air box. Their drop-in design means adding performance is simple. With most vehicles you simply remove the disposable air filter and replace it with a K&N. See applicable instruction sheet for details. Designed to boost horsepower and rate of acceleration. Can be cleaned and used again. High air flow with exceptional filtration. Lasts up to 50,000 miles before cleaning is required depending on driving conditions. Works with original equipment manufacturer vehicle electronics. Emissions legal in all 50 US states- Will NOT void vehicle warranty. Our stock replacement air filters for street vehicles are covered by our famous K&N Million-Mile Limited Warranty and will be the last air filter your vehicle will ever need.Million Mile Limited Warranty®

Read more less

Revo ProPanel FilterHigh-Performance Air Filters OVERVIEW The Revo ProPanel is a high-grade direct replacement filter for your vehicle. Designed as direct replacement filters to fit inside your factory air box and are suitable for road or competition use.   BENEFITS Designed to increase horsepower and rate of acceleration Exceptional filtration High airflow with three layers of foam Lifetime warranty Lasts up to 60,000 miles before cleaning is required depending on driving conditions Works with original manufacturers air box   DESIGN AND PERFORMANCE Why choose foam? Because, compared to paper or other filter technologies, reticulated polyester foam achieves optimum performance against three key criteria: Maximum airflow: the ability to allow air to pass through without causing a large drop in pressure. Cleaning efficiency: the capability to arrest a high proportion of airborne dust while feeding the engine clean air. Dust load-up tolerance: the capability to absorb a large amount of dust without reducing airflow capacity. This design of filter has been used in all fields of motorsport from Formula 1 to the World Rally Championship. The range receives this same attention to detail at the design stage and is then taken into production with consummate quality.   THREE LAYER FOAM SYSTEM Revo ProPanel Filters use multi-layered foam technology to trap dust and dirt while maintaining flow efficiency over time. Using foam increases the filter's surface area and is washable, compared to standard paper and cotton filters which trap dust on the surface and become less efficient the more they are used, choking the engine and reducing performance. The outer core is a coarse foam designed to trap larger particles, the second layer is a medium foam designed to trap most particles and the inner core is fine foam which will trap any particles small enough to reach it. The triple layer foam design ensures an exceptional level of engine protection and long-term performance advantage.     1: Stainless steel wire mesh To avoid erosion, only the highest quality steel is used.   2: Course outer layer:  Stops large pieces of dirt and foreign matter from penetrating further. Straightens airflow into subsequent layers.   3: Medium grade middle layer:  This second filtration layer traps most of the harmful dirt that leads to engine damage.   4: Fine inner layer:  Extracts fine particles while allowing full air flow to the engine for maximum power.     ADVANTAGES OF A REVO PROPANEL FILTER Emissions legal in all 50 US states Will not void vehicle warranty Lifetime warranty (to original purchaser with proof of purchase)     FITTING        Manufacturer Model Engine Year Audi A3 (8V)  1.8 / 2.0 TFSI  2012 > Audi A3 (8V)  1.6 / 2.0 TDI  2012 > Audi TT (Mk3)  1.8 / 2.0 TFSI  2014 > Audi TT (Mk3)  2.0 TDI  2014 > Seat Leon (Mk3)  1.8 / 2.0 TSI  2012 > Skoda Octavia (MK3)  1.8 / 2.0 TSI  2013 > Skoda Octavia (MK3)  1.6 / 2.0 TDI  2013 > Skoda Superb (Mk3)  1.8 / 2.0 TSI  2015 > Skoda Superb (Mk3)  1.6 / 2.0 TDI  2015 > VW Golf Vll (Mk7)  1.8 / 2.0 TSI / GTI / R  2012 > VW Golf Vll (Mk7)  1.6 / 2.0 TDI / GTD  2012 > VW Golf Vlll (Mk8)  GTI 2.0 TSI  2019 > VW Golf Vlll (Mk8)  2.0 TDI  2019 > VW Passat  1.8 / 2.0 TSI  2014 > VW Passat  1.6 / 2.0 TDI  2014 > VW Polo GTI  2.0 TSI  2018 > VW Tiguan  2.0 TSI  2016 > VW Tiguan  2.0 TDI  2016 > VW Touran  1.8 TSI  2015 > VW Touran  1.6 / 2.0 TDI  2015 >

Read more less

Beautifully crafted from the highest quality 3K carbon, the Revo Carbon Series is much more than a visual enhancement. Designed to directly replace restrictive OEM components, the Carbon Series has performance woven in to the core of every product. REVO CARBON SERIES - AIR INTAKE SYSTEM The Revo Carbon Series Air Intake System for the 2.0 & 1.8TSI offers unparalleled performance benefits along with a striking visual addition to your engine bay. The full kit, which comes complete with a matching Carbon Series front scoop, lid, back-pipe and Pro-Panel filter completely replaces any restrictive elements of the OEM intake system, decreasing turbulence and allowing a larger volume of air to reach the turbo more quickly KEY FEATURES Increased Performance Improves Air Flow Efficiency Carbon Series Quality Replaces Restrictive Stock Turbo Elbow Engineered for both LHD and RHD Fitment 16% Larger Air Box Outlet     FULL KIT INCLUDES 90mm Turbo Inlet Hose Machined Inlet Carbon Air Box Lid ProPanel Air Filter Carbon Front Section Coolant Relocation Hose RESEARCH AND DEVELOPMENT All Revo products are designed in-house, allowing our team of engineers to rigorously test products during the design process. Only Revo offers a kit with a 16% larger lid outlet and matching hose, ensuring maximum performance at even Stage 3 and above specification.   GRAPHS To ensure this product would meet our exacting standards and performance, we carried out controlled testing on a Stage 4 Skoda Octavia VRS 2.0TSI running Shell vPower pump fuel on an in-house Dynapak hub dyno. With impressive results in comparison to the standard set up, peak results showed up to +41 WHP and +42 NM over stock with an average of +19whp and +25NM throughout the rev range.     VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V)/td> 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Seat Ibiza Cupra 1.8 TSI 15 - Volkswagen Golf (MK7) 2.0 TSI GTI 14 - Volkswagen Golf (MK7) 2.0 TSI R 14 - Volkswagen Golf (MK7) 1.8 TSI 12 - * Fitments for 1.8 TSI & 2.0 TSI Engines with IHI IS20 and IS38 Turbos INDIVIDUAL PRODUCTS Carbon SeriesCarbon Lid & Hose Kit Carbon SeriesCarbon Scoop Carbon Series Secondary Breather Revo Carbon Series air intake systems perform beautifully. Designed to function no matter the power, Carbon Series intakes look great because of their effective design.

Read more less

Pipercross Rectangle Performance Panel Filter Increased Power Lifetime Warranty Improved Fuel economy Direct replacement 30% less restrictive that your OE filter How will a Pipercross panel filter benefit you? Directly replaces the air filter in your airbox30% more airflow over a standard paper air filterLonger lifespan before cleaning required over cottonEasy cleaning, no dirt caught like with V shaped filter groovesBench tested for improved fuel economy, power and torque outputsLifetime warranty on all replacement and performance road use filtersUnlike their competition, Pipercross have adopted multi layered foam technology for their air filters as opposed to cotton or paper. Why? Because foam has a larger capacity for filtration over cotton or paper. In road use terms this means that a Pipercross filter will flow stronger for longer and maintain peak power output of the vehicle over a cotton or paper counterpart. Whilst the cotton or paper filters begin to restrict airflow due to being thinly stretched over a V shaped wire frame the Pipercross with multi layer technology will continue to perform. The low maintenance and long lifespan aspects of a Pipercross filter come from the special triple layer foam that is used on all Pipercross filters. The outer core is coarse foam designed to trap larger particles, the middle core is Medium foam designed to trap most particles and the inner core is fine foam which will trap the remainder of the particles. The triple layer foam design ensures an exceptional level of engine protection in any conditions. (Length 292mm x Width 177mm) Why Choose Pipercross? Pipercross has been making high performance air filters for the motor sport and domestic markets for over 25 years. Based in Northampton, England Pipercross is situated in the country along with some of the biggest names in motorsport engine design and manufacture in the world. In these 25 years our high performance filters have helped many race teams win major championships on the British, European and World stage. The development work carried out whilst dealing with these teams has enabled us to produce some of the most technologically advanced filters on the market. The flexibility of Pipercross's production plant enables us to produce one off bespoke air filters quickly and cost effectively. From the latest WRC cars to a 2CV competition car, Pipercross can design and produce an air filter that can meet and exceed your specifications.

Read more less

Developed in-house at AIRTEC HQ in the UK, we’ve created a comprehensive solution to improving the car’s original air intake system to allow more flow, whilst maintaining low intake temperatures, improving response, sound as well as aesthetics within the engine bay. There is also the option to add the intake hose and turbo elbow hose – see below. AIRTEC Part No: ATIKVAG5   TECHNICAL DATA As part of our expanding EA888 MQB Platform product range, AIRTEC Motorsport is proud to launch our enclosed air induction kit for the VW Golf R/Audi S3/SEAT Cupra R suitable for track or fast road use. Developed in-house at AIRTEC HQ in the UK, we’ve created a comprehensive solution to improving the car’s original air intake system to allow more flow whilst maintaining low intake temperatures, improving response, sound as well as aesthetics within the engine bay. Having previously designed a number of shielded induction kits for other performance models, we were keen to develop a more extensive intake package for the popular EA888 MQB platform to offer further improvements. Featuring a large cotton air filter inside an enclosed housing, our kit features an alloy hard pipe to replace the restrictive OEM air box and intake set up. There is also the option to add our uprated silicone intake hose and turbo elbow hose – see below. To ensure the new air filter doesn’t suffer with heat soak issues from the confines of the engine bay, the two-piece laser cut heat shield protects the air filter and provides a shroud to ensure it channels only fresh air from the front intake. The result is increased power, improved throttle response, heightened induction noise and a more pleasing look to the engine bay. The kit is a direct replacement that requires no additional drilling or cutting to fit, and comes complete with all the correct fixtures and fittings, as well as detailed instructions. Features: Comprehensive intake kit designed specially for the EA888 MQB platform Enclosed air box ensures lower intake temperatures Front intake directs constant feed of cold air to the filter Large cotton air filter for improved flow and increased performance Improved soundtrack and under bonnet aesthetics Long lasting, high quality black powder coat finish Includes all fixtures and fittings     AIRTEC Part No: ATIKVAG5

Read more less

Racingline R600 Carbon Fibre Intake Lid – Gloss/Matte Finish Transform your engine bay with the addition of a true R600 carbon fibre lid. Confirmed Fitment Suitable for existing R600 Intake part numbers; VWR12G7R600 VWR12G7R601 VWR12G7R600E VWR12G7R601E Not suitable for EA888 Gen.4 Engine Vehicles – e.g. S3 8Y, Mk8 Golf R, Cupra Leon Mk4. Applications Please note, customers are wholly responsible for checking fitment for their vehicle.

Read more less

Ramair Jetstream Induction & Turbo Intake Kit (JSK + TI) for vehicles utilizing the MQB chassis platform equipped with the 2.0 TSI (EA888) engine. This kit allows for increased airflow and induction noise over the factory air intake equipment. This kit mounts to standard factory mounting points and rubbers. The kit comprises of… Oversize Turbo Intake Elbow This part allows for increased potential airflow and slightly increased induction sound. The inlet elbow is made from light weight aluminium tube with CNC machined connections and a laser cut bracket, is fully TIG welded and powder-coated in a textured black finish for an OEM look. Jetstream Performance Baseplate Filter Our performance foam air filter, with stainless steel cage construction for superior internal structural support and a spun aluminium neck designed to act as a velocity stack, minimizing turbulence in the intake tract, maximizing flow. The filter element has quick release fittings to enable quick removal, allowing for easy cleaning & maintenance. Silicone Intake Pipe Single piece turbo intake pipe made with 5-ply polyester reinforced silicone, maintaining a constant 80mm diameter and providing excellent protection from high engine bay temperatures. Heat Shield with OEM mounting points Laser cut, precision folded heat shield powder-coated in black, is designed to fit directly to the standard OEM factory air box mounting points and rubbers without the need for modification. The heat shield helps maintain low intake temperatures by providing a physical barrier between the air filter and the rest of the engine bay and directing the air from the factory cold air feed to the area around the filter. Full Fitting Kit Includes all nuts bolts, hose clamps and high quality silicone hose connectors necessary to fit the kit to a standard car (This kit requires utilization of some components from the standard intake pipe and air box). Full Fitting Instructions with Photos Fully detailed step-by-step instructions to guide you through the installation process. This product is suitable for the following vehicles.... Make Model Engine Years Audi A3 (8V) 2.0 TFSI 2013 - 2020 Audi A3 (8V) 1.8 TFSI 2013 - 2020 Audi S3 (8V) 2.0 TFSI 2013 - 2020 Seat Leon (5F) 2.0 TSI Cupra 2013 - 2020 Seat Leon (5F) 2.0 TSI 2013 - 2020 Seat Leon (5F) 1.8 TSI 2013 - 2020 Skoda Octavia (5E) 2.0 TSI 2013 - 2020 Skoda Octavia (5E) 1.8 TSI 2013 - 2020 Volkswagen Golf (mk7) 2.0 TSI R 2013 - 2020 Volkswagen Golf (mk7) 2.0 TSI GTI 2013 - 2020 Volkswagen Golf (mk7) 2.0 TSI 2013 - 2020 Volkswagen Passat (B8) 2.0 TSI 2015 - 2020 Volkswagen Passat (B8) 1.8 TSI 2015 - 2020 Please use the vehicle look up tool at the top of the page to confirm fitment.

Read more less

APR Carbon Open Intake System - MQB - 1.8T and 2.0T EA888 Gen 3The APR Open Carbon Fiber Intake System is the ultimate intake system for the 1.8T/2.0T Engine! We've maximized performance and sound dramatically by reducing pressure drop and increasing airflow. This translates to more horsepower and torque, and less physical strain on the turbocharger. The system looks great, sounds amazing, and produces more horsepower and torque you can feel.Our beautiful carbon fiber intake system does away with the closed airbox design and uses a massive 7" washable and reusable cotton filter with a frontal inlet and 4" rear outlet. This was necessary to limit pressure drop across the factory system and maximize airflow, while allowing you to fully hear the engine breathe! The massive filter provides excellent filtration. By oversizing the filter, we're able to limit pressure drop without sacrificing filtration. This is made possible through the use of greatly increased filter surface area. Carbon fiber not only looks great, but it allows us to make a complex and organic heat shield shape that keeps hot air pushed through the frontal radiator away from the intake tract. Furthermore carbon fiber allows us to limit wall thickness on the intake pipe, maximizing the pipe's internal diameter and thus airflow. Lastly, carbon fiber retains heat less than other materials, such as metal, making it ideal for performance.The factory intake system simply can’t match the performance of our intake system. The full factory frontal airbox only flows 521 CFM at 28” of H2O. We improved this by 60% with our open airbox, which flows 833 CFM by comparison! However, it’s important to always look at the intake system as a whole as flow numbers alone don’t always speak to the broader picture. The factory turbocharger can only flow just under 400 CFM through the factory opening, and any intake system will lessen maximum flow. The goal is to minimize all restrictions before the turbocharger as much as possible to maximize performance. The full factory system brings this down to 275 CFM, or 31% less. The full APR System (Open airbox, rear pipe, and turbo inlet pipe), bring this down to 345 CFM, which is only 13% less, or a 25% improvement over stock! This directly translates to more power you can feel. Our full bolt on APR Tuned S3 saw max gains of 12 AWHP and 13 AWFT-LBS of torque using the full intake system compared to stock! These are solid gains that make a noticeable difference in performance!

Read more less

APR Carbon Intake System - MQB 1.8T / 2.0T EA888 Gen 3 The APR Carbon fibre Intake System is an attractive high performance upgrade for the latest 1.8T and 2.0T engines as found in various MQB platform vehicles. The factory intake design has the foundation for excellent performance, but much of this is sacrificed in an effort to meet other design requirements. With requirements set forth for only supporting factory power output levels, low engine sound levels and long service intervals, there is plenty of room for improvement. The APR Carbon fibre Intake System increases performance primarily by improving mass airflow through the system while still proving adequate filtration. Expect greater horsepower and torque through the power band with a more direct and responsive feel upon pressing the throttle. Sounds from the engine and turbocharger are enhanced and some may even experience better fuel economy depending on driving style.Research and Development: Uncommon to most in the market today, APR spared no expenses during the research and development period. For the better part of a year, APR’s Mechanical Engineers created several prototype intake designs utilizing our in house Sterolithography 3D printer and other rapid prototyping techniques. Various filter mediums were tested in conjunction with the new intake designs through simulated models, flow bench analysis, dyno data collection and in real world applications all in an effort to derive the best possible solution.Intake Air Temperature Management: Intake air temperature (IAT) plays a critical role in engine performance, especially on turbocharged engines where the ambient air temperature is raised twice through both compression via the turbocharger, and then again during the engine’s compression stroke. In an effort to maintain the lowest possible starting IAT, the APR Intake system begins by drawing air from the coldest possible location, which is the front end of the vehicle before the radiator. Air travels a short path through the intake system, past the filter and on its way to the turbocharger through a sealed intake design that prevents ingestion of hot, under-hood air. Finally, the intake’s carbon composite design features a thin fibreglass backing, which improves thermal insulative properties. Filtration: APR’s design requirements called for an intake filter medium that exhibited high flow capabilities, long service life and adequate filtration properties. While traditional paper filters and even some foam filters can achieve one or more of these requirements, only a pleated cotton filter was able to achieve all three. This is due in part to the intake housing’s volute design and turning vanes. With even pressure flow distribution across the entire filter element, the filter is loaded more evenly, retaining performance over time, increasing the length of the maintenance intervals, and increasing the filter's effectiveness.Sound: In an effort to please customers unaware of the sounds caused by turbocharging an engine, as well as cross platform use on both economy and performance oriented vehicles, the OEM was tasked with creating an intake that many would consider to be too quiet for a performance vehicle. APR’s design requirements called for an intake system that only delivered the engine’s true turbocharged sound as air is sucked through the turbocharger or exhausted from the diverter valve upon lifting off the throttle. The inherent stiffness of carbon fiber composite material results in an induction resonance from the engine allowing the occupants to hear a clean and crisp intake note without being overbearing or cheap sounding in nature.Installation: The intake system comes pre-assembled from APR ready to be installed in minutes with minimal tools. With the factory unit removed, the intake slips into place and connects to the factory turbo inlet pipe using the OEM hardware without filling the engine bay with additional couplers and hose clamps. Because the system fits in the OEM location, it’s fully compatible with future upgrades from APR, including our larger Stage III Turbocharger Systems.Optional APR Silicone Coolant Hose:The factory coolant hose is designed to be routed over the top of the intake system. However, when routed underneath the intake, it’s far more aesthetically appealing. The APR coolant hose replaces the factory unit and routes cleanly under the intake and around the APR catch can without kinking or adding extra stress to the mounting points.

Read more less

Turbo Inlet Hose The Revo Turbo Inlet Hose has been designed and engineered to directly replace the stock pipe and elbow found in vehicles with the 1.8 and 2.0 TSI engines with an IHI turbo. The Revo Turbo Inlet Hose offers a high-quality single piece replacement for the OEM parts which allows for smoother uninterrupted air flow, improving the throttle response and performance of your vehicle. Key Features Increased performance Improves air flow efficiency Constant taper for smoother flow Turbo matched inlets Replaces restrictive stock turbo elbow Engineered for both LHD and RHD fitment OEM Part With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running Revo Software. With a generously sized air box, the standard plastic intake hose causes the most amount of restriction; convolutions designed to allow for engine movement disrupt airflow, a small internal diameter limits the volume of air and a sharp reduction in hose diameter at the turbo causes turbulence. Turbo Inlet The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The machined billet aluminium inlet securely fits to the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence. Silicone Hose Design The Revo Turbo Hose as an increased inner diameter that gradually tapers from air box to turbo to optimise airflow, while maintaining the tolerances required to fit both LHD and RHD vehicles with a standard air box. Designed to directly replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range. A four-ply construction with an internal wire helix increases strength to prevent collapsing under pressure. Internal steps flush fit against the stock air box and the machined inlet, creating a smooth transition between components ensuring the smoothest airflow possible to the turbo. A machined bung is integrated in to the hose, connecting the stock PCV system vacuum. Research and Development All Revo products are designed in-house and are rigorously tested. The Revo Turbo Inlet Hose allows the Stock IS38 turbo to run more efficiently, intake a larger volume of air and minimise turbulence. This increases power and torque, especially at the top end of the rev range as highlighted during controlled Dyno testing. Graphs Data Up to 12WHP and 15NM gains Graphs produced with Revo stage 2 software on Audi S3 8V Stock Runs with complete OEM Air intake setup Revo Runs with Revo Intake Hose and ProPanel Filter Technical Documents The following documents are available to view: Fitting instructions Download the Revo Turbo Inlet Hose Fitting Instructions Vehicle Applications Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V) 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Volkswagen Golf (MK7) R 2.0 TSI 12 - Volkswagen Golf (MK7) GTI 2.0 TSI 12 - Volkswagen Golf (MK7) 1.8 TSI 12 - * Fitments for 1.8 TSI & 2.0 TSI Engines with IHI IS20 and IS38 Turbos © Revo Technik

Read more less

Ramair Jetstream Induction Kit (JSK) for vehicles utilizing the MQB chassis platform equipped with the 2.0 TSI (EA888) engine. This kit allows for increased airflow and induction noise over the factory air intake equipment. This kit mounts to standard factory mounting points and rubbers. The kit comprises of… Jetstream Performance Baseplate Filter Our performance foam air filter, with stainless steel cage construction for superior internal structural support and a spun aluminium neck designed to act as a velocity stack, minimizing turbulence in the intake tract, maximizing flow. The filter element has quick release fittings to enable quick removal, allowing for easy cleaning & maintenance. Silicone Intake Pipe Single piece turbo intake pipe made with 5-ply polyester reinforced silicone, maintaining a constant 80mm diameter and providing excellent protection from high engine bay temperatures. Heat Shield with OEM mounting points Laser cut, precision folded heat shield powder-coated in black, is designed to fit directly to the standard OEM factory air box mounting points and rubbers without the need for modification. The heat shield helps maintain low intake temperatures by providing a physical barrier between the air filter and the rest of the engine bay and directing the air from the factory cold air feed to the area around the filter. Full Fitting Kit Includes all nuts bolts, hose clamps and high quality silicone hose connectors necessary to fit the kit to a standard car (This kit requires utilization of some components from the standard intake pipe and air box). Full Fitting Instructions with Photos Fully detailed step-by-step instructions to guide you through the installation process. This product is suitable for the following vehicles.... Make Model Engine Years Audi A3 (8V) 2.0 TFSI 2013 - 2020 Audi A3 (8V) 1.8 TFSI 2013 - 2020 Audi S3 (8V) 2.0 TFSI 2013 - 2020 Seat Leon (5F) 2.0 TSI Cupra 2013 - 2020 Seat Leon (5F) 2.0 TSI 2013 - 2020 Seat Leon (5F) 1.8 TSI 2013 - 2020 Skoda Octavia (5E) 2.0 TSI 2013 - 2020 Skoda Octavia (5E) 1.8 TSI 2013 - 2020 Volkswagen Golf (mk7) 2.0 TSI R 2013 - 2020 Volkswagen Golf (mk7) 2.0 TSI GTI 2013 - 2020 Volkswagen Golf (mk7) 2.0 TSI 2013 - 2020 Volkswagen Passat (B8) 2.0 TSI 2015 - 2020 Volkswagen Passat (B8) 1.8 TSI 2015 - 2020 Please use the vehicle look up tool at the top of the page to confirm fitment.

Read more less

We are pleased to present the cold air intake system for ‘RoW’ Market MK7 Golf 1.4TSI with EA211 engine. The CTS intake system is constructed from T6061 aircraft grade aluminum and offers superior heat dissipation, improved airflow, and cooler intake temperatures. The CTS air box connects seamlessly to the factory air inlet drawing cool air from outside of the engine bay while deflecting radiant heat from the engine bay. Improving airflow and reducing intake temperatures increases power, and fuel economy while reducing spool up time. The turbo and the diverter valve sounds become a lot more noticeable and make the car more fun to drive! Please use the engine bay image to confirm it is that same style. HP gain: 9-10hp

Read more less