Performance - Peugeot 208 GTI

The Forge Motorsport high flow inlet hose for the Peugeot 208 GTI face lift model from late 2016 onwards (208bhp EP6-FDTX Euro 6 Engines) replaces the restrictive plastic inlet pipe with our smooth bore multi-ply silicone hose which increases air flow, improving efficiency and performance.  Available in red, blue, or black, and is supplied with all necessary hose clamps and adapters for a straight forward fit. This is a replacement for the OEM factory inlet hose, you can check compatibility by refrencing the OEM part number. OEM Number 9805501580-03 The Forge silicone hose in this kit has been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) but more importantly for this application, air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically The use of a Fluorosilicone liner ensures that Forge silicone hoses are the clear market leader. Lifetime warranty*   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The FMDVMCS is a sandwich type adaptor that fits between the existing electrical solenoid and the turbo charger housing on the BMW Mini Cooper S N14 engines 2007/08(R56/57 *), Peugeot 1.6 turbo engines as found in the 207 and GTI , 208 GTI, 307, 308 and Citroen DS3. On these engines, built into the turbocharger housing, is a bypass facility. This allows charge air to be recirculated around the turbo charger from the boost side back to the intake side. This recirculation path is opened and closed by means of an electrical connection from the engine management, to a solenoid that is mounted on the turbocharger housing. As you accelerate, the turbo charger vanes are spinning and boost pressure is increased, literally blowing into the engine cylinders. Then when you change gear, you take you foot off the accelerator momentarily, select the next gear, and accelerate again. As you take your foot off the accelerator the throttle valve to the engine closes. The problem here is that during this process the turbo is still spinning and the boost pressure that it is producing has no where to go. (This is a bit like putting you hand over a hair dryer so the air cannot get out) What happens at this point is the turbo starts to stall, the spinning vanes slow down (incurring alot of stress) and the boost pressure drops. When you open the throttle valve again by pushing down on the accelerator (demanding more power) the turbo has lost its momentum, boost pressure and there is a pause or a "Lag" before the engine is producing the required power once again. To combat this loss of power and stress on the turbo, a recirculation or diverter valve is used. On the Mini, when the throttle valve closes, the engine management opens the recirculation route around the turbo. This gives the charge air an alternative route and allows the turbocharger to keep spinning so that when you accelerate again there is no "lag" or waiting period. This system works well and is adopted by nearly all vehicle manufacturers on turbo charged petrol engine applications. The only downside to this system is that a turbo chargers produce heat. (The hot air that leaves a turbo is cooled by passing it through an intercooler before it enters the engine. The cooler the air the more power is produced). By recirculating the hot air back into the intake side of a turbo the temperatures increase. This is where the Blow Off or Dump valve plays its part. By expelling the charge air to atmosphere rather than recirculating it, you do not increase the intake air temperature but you do allow the turbo to keep spinning. The side effect which is unacceptable to most vehicle manufacturers is the noise of the valve expelling the air. By fitting the FMDVMCS between the existing solenoid and the turbo housing (this involves removing only 3 bolts) the air is re-directed to atmosphere rather than recirculated. It should be noted that the engine management also uses this valve to decrease engine power when necessary. An example of this is by the (DSC) Dynamic Stability Control system. Although you would not normally hear this occurring, when a blow off adaptor is fitted you may well hear the air being expelled when the DSC operates (going too fast around a bend for example).   In The Box1 x FMDVMCS Adaptor3 x Socket Cap Bolts1 x Instructions1 x Forge Sticker In order that you purchase the correct valve for your vehicle please refer to the fitment table below before ordering. Product Code Fitment FM207V Recirc Valve N14 Engines Cooper S 2007-10, JCW Cooper S 2007-2012 FMDVR60R Recirc Valve N18 Engines Cooper S 2011 On, JCW Cooper S 2013 onwards FMDVMCS Blow Off Adaptor Plate For 2007/8 Cooper S Turbo only FMDVR56A Blow Off Valve N14 Engines Cooper S 2007-10, JCW Cooper S 2007-2012 FMDVR60A Blow Off Valve N18 Engines Cooper S 2011 On, JCW Cooper S 2013 onwards    This product is available in machined alloy finish only. N14 Engine Mini Mini R56 Cooper S 1598ccm 174HP 128KWMini R56 John Cooper Works 1598ccm 211HP 155KWMini R57 Cooper S 1598ccm 174HP 128KWMini R57 John Cooper Works 1598ccm 211HP 155KWMini Clubman R55 Cooper S 1598ccm 174HP 128KWMini Clubman R55 John Cooper Works 1598ccm 192HP 141KWMini Clubman R55 John Cooper Works 1598ccm 211HP 155KW   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport 208 GTi hardpipes replace the turbo to intercooler and intercooler to throttle body plastic pipes on the top of your engine. We also include the silicon hose exiting the turbo which is available in red, blue or black. These pipes are more free flowing than stock by removing the resonators and can be fitted to the stock intercooler hoses, or our full front mounting intercooler kit FMINT208GTi. PLEASE NOTE: THIS WILL ONLY FIT THE GTI MODEL AND NOT THE GT WITH 156BHP   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

The Forge Motorsport FMTUBL4 has been specifically designed for the Mini R56 stock turbo charger, and also fits the Peugeot 207/208 GTI. This turbo blanket is designed to isolate the radiant heat produced by the turbocharger. The stock Mini heat shield is inadequate and can result in warping the standard air scoop located in the bonnet. This design has been created to withstand the harshest of environments and proven to withstand temperatures up to 2500 °f of radiant heat which will assist in protecting and prolonging the life of engine components. Design innovation keeps the heat of the exhaust gases contained within the hot side of the turbocharger, away from the cool side and the intake path which helps reduce turbo lag and air intake temperatures resulting in more power. Please note that a turbo blanket will lose its flexibility over the first few heat cycles as the material cures, so once fitted it should not be routinely removed as this can cause damage to the blanket.   ·       Stainless Steel Rivets ·       Stainless Steel Fasteners ·       Carbon fabric outer shell ·       Calcium Magnesium Silicate Wool constructed Inner Core ·       High temperature Silica fabric   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less