Revo Hardware

OEM+ INTAKE The Revo open cone Air Intake System for the Ford Ranger improves performance and removes restrictions found in the OEM system. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock plastic intake pipe and filter. This kit comes complete with a silicone hose, air filter and fitting kit. KEY FEATURES Increased Performance Improved Air Flow Efficiency Three Stage Foam Filter with Mesh Stepped Silicone Hose OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. OEM+ systems utilise the stock airbox but remove other restrictive parts to enhance airflow to the turbo. Revo Flush Fit silicone hoses mean joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at any level of tuning. SILICONE HOSE The Revo intake hose is designed to directly replace the plastic corrugated parts. The 4ply silicone intake hose reduces turbulence and internal restrictions. The smooth internal bore results in no loss of cross-sectional area and allows increased airspeed through the intake. FILTER An intake system is only as good as the filter. This kit comes complete with a custom Revo foam filter, supported by galvanised epoxy-coated mesh for strength under load. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze alternatives designed to trap particles on the outer layer. Revo filters trap debris and particles within the foam layers, allowing air to still navigate through. The filter is also reusable. ADDITIONAL FEATURES The Revo hose also keeps the OE PCV take-off location and is supplied with a CNC machined 6061 adaptor which offers greater durability than the stock plastic take-off. The hose clamps supplied with this kit are made of stainless steel. This means they not only have high tensile strength but also will not corrode over time causing a failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase airflow, as highlighted during controlled testing.   LOWERING TEMPERATURES To show the efficiency of the Revo Intake, airflow was measured using our own Ford data logging software. Logging a 3rd and 4th gear pull through the rev range you see the improvements of the Revo Intake compared to stock. The Revo intake manages to hold consistent airflow through the gear change and gives a maximum airflow gain of 16% with an average of 5% throughout the runs.     FITTING      Manufacturer Model Engine Year Ford Ranger 2.2 TDCI 2015 - Ford Ranger 3.2 TDCI 2015 -

Read more less

OPEN CONE INTAKE The Revo open cone Air Intake System for the 2.0T Gen3 engine improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo ECU Software. Engineered to directly replace the stock airbox, pipework and filter, this kit comes complete with a silicone hose, aluminium pipe, heat shield, filter, machined turbo coupler and fitting kit. KEY FEATURES Increased Performance (+12BHP +23Nm) Improved Air Flow Efficiency Three Stage Foam Filter with Mesh Direct to turbo fitment OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and silicone hose which joins directly to the turbo. Revo Flush Fit silicone hoses avoid unwanted turbulence at joins, and increase the rate at which air can flow ensuring maximum performance at any level of tuning. SILICONE HOSE The Revo silicone hose as an increased inner diameter that gradually tapers from hard pipe to turbo to optimise airflow. Designed to directly replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range. A machined billet bung is integrated into the hose, connecting the stock PCV system vacuum. TURBO INLET The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The billet aluminium inlet securely fits the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence. HEATSHIELD Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points to provide easy and secure installation. FILTER An intake system is only as good as the filter. This kit comes complete with a custom Revo foam filter, supported by galvanised epoxy-coated mesh for strength under load. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze alternatives designed to trap particles on the outer layer. Revo filters trap debris and particles within the foam layers, allowing air to still navigate through.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled dyno testing.   PERFORMANCE DATA Back-to-back testing of the stock air intake system and the Revo kit were carried out. Fitted to an Audi S3 (310PS Model) with Revo ECU Software, Revo Intercooler, Revo Charge & Throttle Pipes and Revo Downpipe. The results show improvement throughout the whole rev range. The Revo intake offering an average gain of +12WHP, and +18NM torque over the stock part. Increased airflow also delivers impressive peak performance gains of +19.4BHP @6000rpm and +55NM @2400RPM over the stock intake system. AIRFLOW To evaluate the efficiency, the Revo Intake was tested for inlet charge pressure and mass airflow. Boost pressure was measured and an increase in charge pressure was seen across the top end of the RPM range, as detailed in the dyno graph. Intake mass airflow logging showed similar results to the charge pressure, showing considerable increases at the top of the RPM range.     FITTING      Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V)/td> 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Seat Ibiza Cupra 1.8 TSI 15 - Volkswagen Golf (MK7) 2.0 TSI GTI 14 - Volkswagen Golf (MK7) 2.0 TSI R 14 - Volkswagen Golf (MK7) 1.8 TSI 12 -

Read more less

The factory 2.0 TFSI air-box works efficiently on a standard vehicle. As power is increased through tuning, however, it quickly becomes a major restriction, reducing the additional power offered. Ensuring the engine can get access to enough air is paramount when increasing power, an open cone air-intake system is the most effective way of achieving this, but not all products are made equal. Having worked with a number of intake solutions during software development, we noticed a lack of high quality and more importantly, high flowing kits available. Working alongside some of the biggest names in the air filter industry, we engineered and designed what is still one of the highest flowing kits available. Pioneering design allows air to reach the turbo as quickly as possible whilst minimising turbulence and restriction. As a result, boost can be maintained for longer, giving you access to more power throughout the rev-range along with a more aggressive sound, and performance you can feel all the way to the redline. BENEFITS Increases power and torque Maintains boost for longer Single piece pipe 25% less restriction Three-layer foam filter Scaled MAF housing CamCoat option available INTAKE PIPE The Revo engineering team knew that to create the most effective kit, every component had to be considered to maximise and smooth airspeed. The system is designed around a lightweight 90mm intake pipe, mandrel bent to maintain the internal diameter in the corners and to create a one-piece solution. This offers superior flow and avoids the air turbulence and resistance experienced on intake kits with multiple sections, usually caused at each join resulting in very turbulent airflow, ultimately restricting performance. MAF SCALING Ensuring correct MAF (Mass Air Flow) sensor scaling is the real art when it comes to designing air intake systems if incorrect the intake system can actually reduce power and cause major fuelling issues. The Revo kit integrates the stock MAF sensor in a specifically designed housing on the one-piece pipe to ensure correct scaling during fitment. THREE LAYER FOAM FILTER An intake system is only as good as the filter. This kit comes complete with a tried and tested Revo three-layer foam filter with an impressive 857cm² surface area, supported by galvanised, epoxy-coated mesh to ensure the filter cannot collapse. The filter has a large 180mm external diameter body and a smooth radius aluminium bell mouth, specifically designed for optimum airflow from the filter to pipe-work. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze, which are surface filters designed to trap particles on the outer layer, instantly causing restriction. Revo foam filters work by trapping dirt particles within each of the oiled foam layers, allowing air to negotiate its way through the filter, reducing restriction and offering much longer service intervals. We tested the filter at a leading motor testing centre ‘Mira’ on an industry recognised dust load test. On a full dust load test, the foam filter was found to still be 99.1% efficient, filtering down to 5 microns while offering the least amount of restriction over similar products. HEAT SHIELD The intake system features a laser-cut aluminium heat shield that ensures the filter is well insulated from ambient under-bonnet temperatures. The shielding is designed to utilise the ducting in the factory grill to maximise airflow and prevent heat-soak. SILICONE HOSE The silicone hoses included in the kit are manufactured using high-quality automotive grade silicone, engineered to combine the system using stepped necks to offer a smooth transition of air to avoid turbulence. The turbo inlet hose has also been specifically designed to fit both K03 and K04 turbo powered cars. TESTING 2.0 TFSI Intake Restriction  2.0 TFSI Stock vs Stage 1 Power Graph 2.0 TFSI Stock vs Stage 1 Power Graph   INTAKE PERFORMANCE FIGURES Engine Software Power Torque 2.0 TFSI (K03) Stage 1 + 16 BHP + 5 NM 2.0 TFSI (K04) Stage 2+ + 40 BHP + 15 NM   *Maximum power and torque increases are shown in testing when using Revo 2.0 TFSI intake system compared to a stock intake   TECHNICAL DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the RT992M200700 Revo 2.0 TFSI Air Intake System Fitting Instructions     FITMENT      Manufacturer Model Engine Year Audi A3 (8P) 2.0 TFSI 2006 - 2012 Audi S3 (8P) 2.0 TFSI 2006 - 2012 Seat Leon MK2 2.0 TFSI 2005 - 2012 Seat Altea 2.0 TFSI 2006 - 2009 Skoda Octavia Mk2 2.0 TFSI 2005 - 2013 VW Golf MK5 2.0 TFSI 2003 - 2009 VW Golf MK6 (R, ED35) 2.0 TFSI 2008 - 2013 VW Scirocco R 2.0 TFSI 2008 > VW Jetta 2.0 TFSI 2006 - 2010 VW Passat 2.0 TFSI 2005 - 2010

Read more less

EVERYTHING YOU NEEDFOR THE POWER YOU CRAVE Enhanced power delivery, unique safety features and exhilarating response at your disposal, the Revo Performance Pack delivers much more than peak power figures. Whatever drives you, the Revo Performance Pack has it all. Engineered to perform, only Revo offers a complete tuning solution specifically designed for your vehicle. AIR INTAKE SYSTEM PERFORMANCESOFTWARE INTERCOOLER PIPE UPGRADE KIT INTERCOOLER     CARBON SERIESAIR INTAKE SYSTEM Beautifully crafted from the highest quality 3k carbon, the Revo Carbon Series is much more than a visual enhancement. Designed to directly replace restrictive OEM components, the Carbon Series has performance woven into the core of every product. IncreasedDiameter DirectInternals ThermalBarrier Learn more about this product OPEN CONEAIR INTAKE SYSTEM Revo Open Cone Air Intake Systems completely replace the OEM air intake for those who like to announce their vehicle is far from standard. Along with an aggressive intake sound, more air means access to more power throughout the rev-range. IncreasedFlow DirectReplacement IncreasedDiameter Learn more about this product     PERFORMANCE ECU SOFTWARE Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev range while maintaining the extensive factory safety mechanisms. Revo Software offers a perfect balance of performance, economy, longevity, and safety so you can drive harder, for longer. OBDII PortInstalled Vehicle HealthCheck Authorised DealerSet-up Read More TCU SOFTWARE Revo Transmission Control Unit Software allows your automatic gearbox to work in harmony with Revo ECU Software. As well as enhanced driveability and quick shifts, Revo TCU Software is packed full of features. OptimisedShift Points DynamicLaunch Control GlobalDevelopment Programme Read More     INTERCOOLER PIPE UPGRADE KIT The Revo Intercooler Pipe Upgrade kit reduces charge system resistance and improves flow over the restrictive stock pipework. Featuring fewer restrictions for smoother airflow, and optimised routing, the turbo meets less resistance and can perform more effectively. DirectReplacement IncreasedDiameter DirectInternals Learn more about this product INTERCOOLER UPGRADE The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Unique design features lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software, ensuring you get consistent performance when you need it most. DirectReplacement UniqueFin Design MinimisedPressure Drop Learn more about this product     STOCK POWER300PS TORQUE380NM 0 - 60 MPH4.6S 100 - 200 KPH14.2S POWER400PS TORQUE550NM 0 - 60 MPH3.6S 100 - 200 KPH8.8S Find your nearest Revo Authorised Dealer Manufacturer Model Variant Engine Year Audi S3 8V 2.0 TFSI 2014 - 2019 Audi TTS 8S 2.0 TFSI 2014 > SEAT Leon Cupra 5F 2.0 TSI 2014 - 2019 Skoda Superb 3V 2.0 TSI 2014 - 2019 VW Arteon 3H 2.0 TSI 2017 > VW Golf R Mk7 2.0 TSI 2014 - 2019 VW Golf GTI Clubsort Mk7 2.0 TSI 2016 - 2018 VW Golf GTI Clubsort S Mk7 2.0 TSI 2016 - 2017 Images shown are for illustration purposes only All software and features are ECU/TCU ID dependant. Upgrade pricing is for existing Revo ECU or/and TCU customers.  Terms and Conditions apply.  Exhaust Overrun is an seperate file option that can be choosen at point of software installation. Performance data is taken from 2016 VW Golf R Mk7 with DSG. Aftermarket downpipe required. Pricing does not include the installation of parts, please contact your local Revo Authorised Dealer.

Read more less

Beautifully crafted from the highest quality 3K carbon, the Revo Carbon Series is much more than a visual enhancement. Designed to directly replace restrictive OEM components, the Carbon Series has performance woven in to the core of every product. REVO CARBON SERIES - AIR INTAKE SYSTEM The Revo Carbon Series Air Intake System for the 2.0 & 1.8TSI offers unparalleled performance benefits along with a striking visual addition to your engine bay. The full kit, which comes complete with a matching Carbon Series front scoop, lid, back-pipe and Pro-Panel filter completely replaces any restrictive elements of the OEM intake system, decreasing turbulence and allowing a larger volume of air to reach the turbo more quickly KEY FEATURES Increased Performance Improves Air Flow Efficiency Carbon Series Quality Replaces Restrictive Stock Turbo Elbow Engineered for both LHD and RHD Fitment 16% Larger Air Box Outlet     FULL KIT INCLUDES 90mm Turbo Inlet Hose Machined Inlet Carbon Air Box Lid ProPanel Air Filter Carbon Front Section Coolant Relocation Hose RESEARCH AND DEVELOPMENT All Revo products are designed in-house, allowing our team of engineers to rigorously test products during the design process. Only Revo offers a kit with a 16% larger lid outlet and matching hose, ensuring maximum performance at even Stage 3 and above specification.   GRAPHS To ensure this product would meet our exacting standards and performance, we carried out controlled testing on a Stage 4 Skoda Octavia VRS 2.0TSI running Shell vPower pump fuel on an in-house Dynapak hub dyno. With impressive results in comparison to the standard set up, peak results showed up to +41 WHP and +42 NM over stock with an average of +19whp and +25NM throughout the rev range.     VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V)/td> 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Seat Ibiza Cupra 1.8 TSI 15 - Volkswagen Golf (MK7) 2.0 TSI GTI 14 - Volkswagen Golf (MK7) 2.0 TSI R 14 - Volkswagen Golf (MK7) 1.8 TSI 12 - * Fitments for 1.8 TSI & 2.0 TSI Engines with IHI IS20 and IS38 Turbos INDIVIDUAL PRODUCTS Carbon SeriesCarbon Lid & Hose Kit Carbon SeriesCarbon Scoop Carbon Series Secondary Breather Revo Carbon Series air intake systems perform beautifully. Designed to function no matter the power, Carbon Series intakes look great because of their effective design.

Read more less

Revo ProPanel FilterHigh-Performance Air Filters OVERVIEW The Revo ProPanel is a high-grade direct replacement filter for your vehicle. Designed as direct replacement filters to fit inside your factory air box and are suitable for road or competition use.   BENEFITS Designed to increase horsepower and rate of acceleration Exceptional filtration High airflow with three layers of foam Lifetime warranty Lasts up to 60,000 miles before cleaning is required depending on driving conditions Works with original manufacturers air box   DESIGN AND PERFORMANCE Why choose foam? Because, compared to paper or other filter technologies, reticulated polyester foam achieves optimum performance against three key criteria: Maximum airflow: the ability to allow air to pass through without causing a large drop in pressure. Cleaning efficiency: the capability to arrest a high proportion of airborne dust while feeding the engine clean air. Dust load-up tolerance: the capability to absorb a large amount of dust without reducing airflow capacity. This design of filter has been used in all fields of motorsport from Formula 1 to the World Rally Championship. The range receives this same attention to detail at the design stage and is then taken into production with consummate quality.   THREE LAYER FOAM SYSTEM Revo ProPanel Filters use multi-layered foam technology to trap dust and dirt while maintaining flow efficiency over time. Using foam increases the filter's surface area and is washable, compared to standard paper and cotton filters which trap dust on the surface and become less efficient the more they are used, choking the engine and reducing performance. The outer core is a coarse foam designed to trap larger particles, the second layer is a medium foam designed to trap most particles and the inner core is fine foam which will trap any particles small enough to reach it. The triple layer foam design ensures an exceptional level of engine protection and long-term performance advantage.     1: Stainless steel wire mesh To avoid erosion, only the highest quality steel is used.   2: Course outer layer:  Stops large pieces of dirt and foreign matter from penetrating further. Straightens airflow into subsequent layers.   3: Medium grade middle layer:  This second filtration layer traps most of the harmful dirt that leads to engine damage.   4: Fine inner layer:  Extracts fine particles while allowing full air flow to the engine for maximum power.     ADVANTAGES OF A REVO PROPANEL FILTER Emissions legal in all 50 US states Will not void vehicle warranty Lifetime warranty (to original purchaser with proof of purchase)     FITTING        Manufacturer Model Engine Year Audi A3 (8V)  1.8 / 2.0 TFSI  2012 > Audi A3 (8V)  1.6 / 2.0 TDI  2012 > Audi TT (Mk3)  1.8 / 2.0 TFSI  2014 > Audi TT (Mk3)  2.0 TDI  2014 > Seat Leon (Mk3)  1.8 / 2.0 TSI  2012 > Skoda Octavia (MK3)  1.8 / 2.0 TSI  2013 > Skoda Octavia (MK3)  1.6 / 2.0 TDI  2013 > Skoda Superb (Mk3)  1.8 / 2.0 TSI  2015 > Skoda Superb (Mk3)  1.6 / 2.0 TDI  2015 > VW Golf Vll (Mk7)  1.8 / 2.0 TSI / GTI / R  2012 > VW Golf Vll (Mk7)  1.6 / 2.0 TDI / GTD  2012 > VW Golf Vlll (Mk8)  GTI 2.0 TSI  2019 > VW Golf Vlll (Mk8)  2.0 TDI  2019 > VW Passat  1.8 / 2.0 TSI  2014 > VW Passat  1.6 / 2.0 TDI  2014 > VW Polo GTI  2.0 TSI  2018 > VW Tiguan  2.0 TSI  2016 > VW Tiguan  2.0 TDI  2016 > VW Touran  1.8 TSI  2015 > VW Touran  1.6 / 2.0 TDI  2015 >

Read more less

REVO CONE CONE AIR INTAKE SYSTEM AUDI S1 2.0 TFSI The Revo open cone Air Intake System for the Audi S1 improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock airbox, pipework and filter on the Audi S1. The Revo System offers a high-quality open cone replacement complete with a heat shield to improve airflow and the performance of your vehicle. KEY FEATURES Increased performance +13HP at hubs & +18NM Torque Improves Air Flow Efficiency 53% Larger Hose & Inlet Volume Three Stage Foam Filter with Mesh Silicone Coolant Hose OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and silicone hose which joins directly to the turbo inlet. Revo Flush Fit joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at all tuning stages. SILICONE HOSE The Revo silicone hose is designed to directly replace the plastic hose and rubber corrugated parts. Increased inlet diameter of 21% reduces restriction and promotes smooth airflow while an integrated wire helix reinforces the hose and prevents collapsing under negative pressure.   MACHINED INLET The machined inlet replaces the restrictive OEM plastic elbow and is designed to securely fit the OE unit using locking tabs and integrated O-rings. Only the Revo intake kit features an inlet almost double the cross-sectional area. This means air can stabilise and distribute before a smooth tapered transition to the turbo.   FILTER AND HEATSHIELD Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points and rubber mounting bushings to provide an easy and secure installation.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled Dyno testing. AIRFLOW  An overall air volume increase of 50% over the OE part allows for faster and increased airflow. The carefully designed silicone hose has its own support bracket mated to a machined hose fitting, maintaining the correct position during engine movement. A constant taper in the hose ensures a smooth transition of airflow from the air filter to turbo and results in an increase in air volume over the stock part. Further helped by the machined inlet that matches the turbo inlet for the ultimate in airflow characteristics.   DYNO GRAPH Testing was carried out on an Audi S1 2.0 TFSI (6 Speed manual) with Revo Stage 1 Software fitted with the OEM system and then the Revo Air Intake System. With a consistent gain throughout the rev range, the Revo intake offered a peak gain of 12HP at the hubs over the stock part. A maximum increase in airflow of up to +16 kg/hr gives impressive gains of 13HP @5100rpm and 18NM @5100RPM over using the stock intake system.   FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi S1 2.0 2014>  

Read more less

The Audi S6 and S7 are impressive cars straight out of the box, yet when combined with Revo’s market leading software they come into a world of their own. In our search to extract more power from the mighty 4.0 TFSI engine, we quickly found that the stock air-box and filter became a major limitation for the car. During research and development, our in-house engineers worked with both the S7 and RS7 to analyse and compare the differences in each intake system, and how efficiently they performed. The direct replacement kit, which includes an RS7 air-box, Revo ProPanel filter and stepped silicone hoses was installed and tested on our in-house S7 development vehicle; the results were staggering. On our Dynopak hub dyno we saw dramatically improved power and torque throughout the rev-range, with consistent gains of +21WHP and +24NM with our Stage 2 software installed. BENEFITS Increases power and torque +21 WHP and + 24 NM gain OEM+ Look Custom designed Silicone hoses Revo ProPanel filter AIRBOX The S and RS air-box may look very similar at a glance, however after analysis and testing of both air-boxes, it was quite clear that the RS air-box had a tremendous amount of potential with a few essential improvements. The two inlet pipes have a larger 100mm diameter, allowing more air to flow with much less restriction compared to the 85mm stock air-box inlets. Revo software really allows the car to utilise this increase in airflow, all without compromising on the OEM look of the engine bay. SILICONE HOSES To compensate for the larger outlets on the RS7 air-box, we designed and developed two larger silicone hoses to join the air intake system to the engine. Revo’s flush fit designed silicone hoses connect to the air-box without any internal restriction, minimising turbulence and allowing a smoother flow of air to maximise performance. REVO PROPANEL FILTER The standard paper filter found in most vehicles performs well under normal conditions, however with increased power it becomes a major choking point in the system. Revo ProPanel filters work by trapping dirt particles within each of the oiled foam layers while allowing air to negotiate its way through, reducing restriction and offering much longer service intervals. We tested the filter at a leading motor testing centre ‘Mira’ on an industry recognised dust load test. On a full dust load test the foam filter was found to still be 99.3% efficient, filtering down to 5 micron while offering the least amount of restriction over similar products. FULL KIT The Revo 4.0 TFSi intake kit comes complete with RS7 air-box, Revo ProPanel filter, silicone hoses and fitting brackets. The kit offers an OEM+ look and fit, with no required modifications to the vehicle, finished off with an aluminium tag.   TESTING Revo 4.0 TFSI intake kit vs Stock     INTAKE PERFORMANCE FIGURES Engine Software Power Torque 4.0 TFSI Stage 2 + 21 BHP + 24 NM   *Maximum power and torque increases shown in testing when using Revo 4.0 TFSI intake system compared to stock intake on Audi S7   TECHNICAL DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the  Revo 4.0 TFSI Air Intake System Fitting Instructions     FITTING      Manufacturer Model Engine Year Audi S6 4.0 TFSI 2012 > Audi S7 4.0 TFSI 2012 >

Read more less

Turbo Inlet Hose The Revo Turbo Inlet Hose has been designed and engineered to directly replace the stock pipe and elbow found in vehicles with the 1.8 and 2.0 TSI engines with an IHI turbo. The Revo Turbo Inlet Hose offers a high-quality single piece replacement for the OEM parts which allows for smoother uninterrupted air flow, improving the throttle response and performance of your vehicle. Key Features Increased performance Improves air flow efficiency Constant taper for smoother flow Turbo matched inlets Replaces restrictive stock turbo elbow Engineered for both LHD and RHD fitment OEM Part With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running Revo Software. With a generously sized air box, the standard plastic intake hose causes the most amount of restriction; convolutions designed to allow for engine movement disrupt airflow, a small internal diameter limits the volume of air and a sharp reduction in hose diameter at the turbo causes turbulence. Turbo Inlet The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The machined billet aluminium inlet securely fits to the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence. Silicone Hose Design The Revo Turbo Hose as an increased inner diameter that gradually tapers from air box to turbo to optimise airflow, while maintaining the tolerances required to fit both LHD and RHD vehicles with a standard air box. Designed to directly replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range. A four-ply construction with an internal wire helix increases strength to prevent collapsing under pressure. Internal steps flush fit against the stock air box and the machined inlet, creating a smooth transition between components ensuring the smoothest airflow possible to the turbo. A machined bung is integrated in to the hose, connecting the stock PCV system vacuum. Research and Development All Revo products are designed in-house and are rigorously tested. The Revo Turbo Inlet Hose allows the Stock IS38 turbo to run more efficiently, intake a larger volume of air and minimise turbulence. This increases power and torque, especially at the top end of the rev range as highlighted during controlled Dyno testing. Graphs Data Up to 12WHP and 15NM gains Graphs produced with Revo stage 2 software on Audi S3 8V Stock Runs with complete OEM Air intake setup Revo Runs with Revo Intake Hose and ProPanel Filter Technical Documents The following documents are available to view: Fitting instructions Download the Revo Turbo Inlet Hose Fitting Instructions Vehicle Applications Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V) 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Volkswagen Golf (MK7) R 2.0 TSI 12 - Volkswagen Golf (MK7) GTI 2.0 TSI 12 - Volkswagen Golf (MK7) 1.8 TSI 12 - * Fitments for 1.8 TSI & 2.0 TSI Engines with IHI IS20 and IS38 Turbos © Revo Technik

Read more less

Revo Air Intake System Seat Ibiza Cupra The Revo open cone Air Intake System for the Seat Ibiza Cupra improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock airbox, pipe work and filter on the Seat Ibiza Cupra. The Revo System offers a high-quality open cone replacement complete with a heat shield to improve airflow and the performance of your vehicle. Key Features Increased performance +25HP at hubs & +30NM Torque Improves Air Flow Efficiency 53% Larger Hose & Inlet Volume Three Stage Foam Filter with Mesh OEM vs Revo When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and silicone hose which joins directly to the turbo inlet. Revo Flush Fit joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at all tuning stages. Silicone Hose The Revo silicone hose is designed to directly replace the plastic hose and rubber corrugated parts. An increased inlet diameter of 21% reduces restriction and promotes smooth airflow while an integrated wire helix reinforces the hose and prevents collapsing under negative pressure.   Machined Inlet The machined inlet replaces the restrictive OEM plastic elbow and is designed to securely fit to the OE unit using locking tabs and integrated O-rings. Only the Revo intake kit features an inlet almost double the cross-sectional area. This means air can stabilise and distribute before a smooth tapered transition to the turbo.   Filter and Heatshield Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points and rubber mounting bushings to provide an easy and secure installation.   Research and Development All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled Dyno testing. Airflow An overall air volume increase of 50% over the OE part allows for faster and increased airflow. The carefully designed silicone hose has its own support bracket mated to a machined hose fitting, maintaining the correct position during engine movement. A constant taper in the hose ensures a smooth transition of airflow from the air filter to turbo and results in an increase in air volume over stock. Further helped by the machined inlet that matches to the turbo inlet for the ultimate in airflow characteristics.   Dyno Graph Testing was carried out on a VW Polo GTI 1.8 TSI (6 Speed manual) with Revo Stage 1 Software fitted with the OEM system and then the Revo Air Intake System. With a consistent gain throughout the rev range, the Revo intake offered a peak gain of 20HP at the hubs and 20NM torque over the stock part. A maximum increase in airflow of upto +16 kg/hr gives impressive gains of 27HP @6100rpm and 30NM @4600RPM over using the stock intake system.   Fitment Vehicle Applications Manufacturer Model Engine Year Seat Ibiza Cupra 1.8 GTI 2016>   Please note: this product will not fit LHD vehicles. Documents The following documents are available to view: Fitting instructions Download the Revo Seat Ibiza Cupra Intake Instructions Notes Simple replacement of the OEM part

Read more less

Revo Air Intake System Ford Focus RS 2.3 EcoBoost With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running more power. The Revo Carbon Series Intake has been designed to promote smoother airflow. Keeping the stock air box helps eliminate heat soak whilst directing cold air through the new filter and 12% larger diameter carbon pipe. Each component has been specifically designed to ensure no air turbulence from joins. This increases the rate at which air can flow, ensuring maximum performance at all tuning stages. Key Features Increased performance Improves air flow efficiency Carbon Series Quality 12% Larger diameter pipe 3 Stage Foam Filter with mesh Carbon Pipe Design The Revo Carbon Pipe has been designed and manufactured from the highest quality 3k carbon to allow a specific bend radius that simply is not possible in aluminium without joins. The increased internal diameter of the pipe is designed to directly replace the plastic hose and rubber corrugated parts. This reduces restriction and maximises smoother airflow to improve both power and torque throughout the rev range. Silicone Hose There is two 4ply silicone hoses included, both offer smooth internals and flush-fit joins onto the carbon pipe for a smooth transition of air. This eliminates unwanted turbulence as the air transitions between parts. The constant taper of the turbo inlet hose allows the airflow time to adjust to the change in pressure, allowing the turbo to run more efficiently. Air Filter The cone shape of the Revo filter was designed to allow more free flowing air around the filter, helping reduce intake temperatures and increase performance, whilst the custom specification mesh allows the filter to keep its shape. The end of the filter has a specially designed spinning which returns into the filter channelling the air to the centre of the outlet, promoting smoother more direct airflow. Research and Development All Revo products are designed in-house and are rigorously tested. By utilising the latest 3D printing technology, the latest CAD and CFD programs, hub dyno and Revo data acquisition software we are able to ensure our products meet the high expectations of Only The Driven. The Revo carbon intake allows the RS turbo to run more efficiently, intake a larger volume of air and minimise turbulence. This increases power and torque, especially at the top end of the rev range as highlighted during controlled dyno testing. Airflow A constant taper in the hose ensures a smooth transition of airflow from the airbox to turbo and results in an increase in air volume over stock. Further helped by fully stepped internals that match to the outlet and inlet for the ultimate in airflow characteristics.Designed to fit in exactly the same way as the factory part, while the Revo kit has significantly increased the volume of airflow through the larger carbon pipe and smoother transitions, the same OE fit is retained. Dyno Graph Testing on the Revo Ford Focus RS fitted with a Revo Performance Pack, the Revo carbon series intake gave a healthy gain of 13WHP and 10NM at peak over the stock unit, with a consistent gain throughout the rev range.At higher RPM, a maximum increase airflow of 11 g/s allows the stage 2 package pulls together all the uprated components and gives an impressive 16whp and 18NM @ 6500rpmon using the stock intake. Fitment Vehicle Applications ManufacturerModelEngineYear Ford Focus RS 2.3 EcoBoost 2016>

Read more less

REVO OEM+ INTAKE SYSTEM Get impressive performance benefits without compromising on the factory look of your engine bay. Revo OEM+ Air Intake Systems utilise the existing airbox, replacing any restrictive components with parts precisely engineered to reduce turbulence and improve airflow. The B9 Audi A4 shares the same airbox as the higher powered S4 and RS4 models and performed well during initial testing of volume and flow. This air intake system upgrade includes a Revo foam filter and a flush-fit silicone hose to minimise air restriction and turbulence, improving airflow and giving you access to more power. KEY FEATURES Increased Airflow by up to 20% Three-layer foam filter Stepped Silicone Hose +11Hp and 13NM performance gains KIT CONTENTS Revo ProPanel Filter Revo Silicone Hose Revo Takeoff Stainless Steel Clamps AIRFILTER The standard paper filter found in most vehicles performs well under normal conditions, however, with the increased power it becomes a major choking point in the system. Revo filters work by trapping dirt particles within each of the oiled foam layers while allowing air to negotiate its way through, reducing restriction and offering much longer service intervals. The new Revo filter features an OEM top plate, allowing a direct fit replacement for the stock airbox. SILICONE HOSE The plastic hose on the stock system is designed with a corrugated style to flex with the engine movement, while this has its place it also causes a large amount of turbulence as the airflow doesn’t have a smooth direct path to the turbo. We designed the silicone hose with stepped internals to ensure a flush fit, and to minimise turbulence while still allowing for engine movement. SELF-SEAL TAKEOFF The OE B9 A4/A5 intake hose has a small vacuum take-off used to supply vacuum to various components of the engine. To replicate this, the Revo B9 A4/A5 intake hose utilizes a threaded self-seal barb. This machined configuration offers a better aesthetic and more durability than typical plastic and glued couplers.   PERFORMANCE  Testing was carried out with consistent conditions on both the OEM intake and the Revo OEM+ Intake System on a 2017 Audi A4 B9 2.0 TFSI Quattro (252ps) running Revo Performance ECU Software and hardware. While dyno testing for performance gains, VCDS software was used to log airflow with a full AEM logging suit used to monitor temperatures. The Revo Intake increased vehicle performance, especially higher in the rev range, highlighting the performance benefits over the stock components.   AIRFLOW Testing of the stock unit back to back against the Revo OEM+ kit on a full flow bench was carried out to highlight the largest restrictions in the system. The Revo OEM+ Intake system had far less restriction than the OE unit, at 480CFM the stock unit was seeing 619mmwg restriction while the Revo unit only saw 530mmwg some 14% less restrictive. At low flow rate the Revo intake provided up to 20% less restriction, improving throttle response. The graph below shows the flow test and comparison between the OE and Revo intakes.   FITMENT   Manufacturer Model Engine Variant Year Audi A4 2.0TFSI B9 252PS 2015> Audi A5 2.0TFSI B9 252PS 2015> Audi Q5 2.0TFSI B9 252PS 2015> *Note: Plastic airbox lid not included in the kit.   DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo Audi B9 2.0 TFSI Intake Instructions  

Read more less