remap

DQ381 TCU SOFTWARE  Save £200! when you purchase ECU and TCU software together IS38 ALL-WHEEL-DRIVE VEHICLES The DQ381 gearbox was released into Volkswagen AG passenger vehicles back in 2017. The 7-speed dual-clutch gearbox (0GC) was derived from the advanced development of the previous 7-speed gearboxes, such as the DQ380 (ODE) and DQ500 (0BT), which had been used in commercial vehicles from 2010 and passenger vehicles since 2011. One key feature of the DQ381 gearbox was principally aimed at increasing efficiency. Unlike the DQ380 gearbox, the DQ381 was designed to be used in both FWD and all-wheel drive vehicles on the MQB chassis platform, such as the Mk7 Golf  R, Audi S3, SQ2 and Cupra Ateca.  This 7-speed wet clutch gearbox is already an improvement over the previous DQ250 6-speed, in terms of allowing the vehicle to shift more efficiently, and with a smother gearchange due to the closer gear ratios. However, driving a DQ381 equipped vehicle you will know that there are still areas that can be improved, especially on performance modes. With the stock calibration, you may find that gear shifts happen too low in the RPM range, or too high when in sports mode. These can lead to unsmooth driving, or make the vehicle feel too aggressive. You may have also experienced clutch slip when running performance ECU Software. IT'S ALL ABOUT THE DRIVE. Revo DQ381 TCU software has been designed for the driven. Working on the characteristics of the gearbox to provide a better driving experience and optimal performance when coupled with our performance ECU software. Holding the gears better in sports mode so it’s not changing up early and allows the engine to be in the right power band more of the time. Revo TCU Software gives you much more than just increased clamping pressure and quicker shifts. A large part of development is based on driving scenarios and feedback, ensuring an exhilarating experience. Expect smooth and refined response at low RPM & partial throttle, with optimal shift programming for wide-open throttle driving.   SOFTWARE FEATURES FASTER SHIFTING Shift times are reduced in auto and manual modes. INCREASED LAUNCH COUNTER The stock launch limit has been raised. INCREASED CLUTCH PRESSURE Maximum clutch pressure is raised to prevent slip. INCREASED CLUTCH TORQUE LIMITS Torque limits are raised to allow to run higher torque levels. OPTIMISED SHIFTING Shift strategy now matches our ECU Software. 3 STEP LAUNCH CONTROL Launch at 3 different points based on throttle position. PROGRESSIVE SOFTWARE The software works with stage 1-3 ECU Software. OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port. MONEY BACK GUARANTEE If not 100% satisfied, we'll give you your money back.     GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU & TCU software.   KEY FEATURES DRIVEABILITY Revo TCU software has been designed alongside our ECU software to not only improve performance but to enhance the feel and driveability of your vehicle. This was the key focus during development, and something that takes time and thousands of miles to achieve. When vehicles are equipped with an Eco/Efficiency drive mode, this uses unique mapping and remains as “stock” to keep all the characteristics. To ensure low RPM driveability, whilst in traffic for example, when you are below 30% throttle input the software will replicate the feel of the stock software. But when required, put the car in Sport/Cupra drive modes, and the gearbox in Drive or Sport and you will be treated to a much-improved sportier feel. PROGRESSIVE SOFTWARE As we produce all our ECU and TCU software in house and have access to vehicles through our global network of authorised Dealers, we have been able to test and refine the software for all ECU stages. This means that our “Progressive TCU” software will work with Stage1 to Stage 3 ECU software on 2.0 TSI DQ381 vehicles. You can install Revo TCU software when at Stage 1 ECU, and it will cover you as you progress through the ECU stages without the need to change TCU software. SHIFTING Gearshift points in gearbox D and S modes have been enhanced and matched with Revo ECU Software. Meaning each gear shift will be at the optimal point to give the best possible performance and fastest acceleration. The shifting times have also been improved and made quicker in D, S and S manual modes. Tested on Stage 2 Audi S3 8V we saw an improvement of up to 0.4s on the 0-60mph time from launch over the stock TCU calibration. The 3-step launch control RPM limits have been optimised to offer 3 different RPM points depending on the throttle input 10-30% launches at 2200rpm, 45-79% launches at 3600rpm and over 80% launches at 4250rpm. When at partial throttle, the gearbox isn’t always looking for the highest gear, it holds the current gear longer. Keeping the turbo spooled and the vehicle within the right power band, thus not changing up and down the gears at much and therefore offering a smoother and more enjoyable drive. Notes: All Revo Software availability is TCU ID Dependant. Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

Please Note: Revo software purchased via CEUK must be installed at our Bradford Workshop. This Can Not be installed at another dealer or by yourself! STAGE 1 AUDI, TT RS, 2.5 TFSI - 2017> Power Torque Stock 400ps  354lbft  REVO Stage 1 Software from 455ps to 490ps  from 416lbft to 435lbft    ONLY THE DRIVEN Revo Performance ECU Software for the 2.5TFSI transforms the way in which the car can be driven. Out of the box, the RS3 demands attention and respect, and rightly so. With 400PS and 480NM torque, an incredible 5 cylinder soundtrack, less weight than the previous model and impressive acceleration times, all the right ingredients are there. Revo ECU Software unleashes the cars full potential and boasts a staggeringly impressive 490PS and 590NM torque, that’s +90PS and +110NM more torque than it rolled out of the factory with. Intensively tested and refined over twelve months, throttle response has been dialled in to give the driver a deeper sense of connection and involvement with the car, something the stock model seems to lack. Rather than being pulled, the hike in torque gives the feeling of a firm push from the bottom of your back, and it’s addictive. The car now begs to be driven hard, it’s now able to break traction in corners, and dares you to bury your right foot. Optimised power delivery and with much more torque at its disposal, you can now drop below 4000rpm and still pull hard out of any corner without hesitation. 2.5 TFSI ENGINE A common issue shared with the pre-facelift 8v RS3, the 2.5TFSI is extremely sensitive to heat and fuel quality. Initial stages of Revo’s Software development process involve pushing the engine harder than usual to find limitations and restrictions. The team found that running more power and torque offered no improvements in acceleration times, negatively affecting the cars ability to consistently perform. Exhaust gas temperatures (EGT) were found to reach up to 960ºC when stock, this highlighted the importance of monitoring EGT’s to avoid risking exhaust catalyst (CAT) and engine failure. Revo Performance ECU Software for the TTRS & RS3 not only utilises the factory safety functions but actually improves them. You can rest assured that your vehicle is able to take all you can throw at it with integrated features exclusive to Revo ECU Software including Cold Start Protection and Temperature Protection which actively monitor oil, intake (IAT) and exhaust temperatures (EGT) and reduce power if they get too high. There’s even an oil temperature based rev limiter should you get heavy footed before the engine oil has sufficiently warmed up.   SOFTWARE FEATURES SPEED LIMIT UNLOCKED The top speed limit for this vehicle has been raised. RPM LIMIT INCREASE RPM Limit has been increased for optimal performance. LEFT FOOT BRAKING Left foot braking has been enabled on this vehicle. TEMPERATURE PROTECTION Enhanced engine cooling from revised thermostatic control. COLD START PROTECTION Increased oil temperature based rev limit. SERIAL PORT SWITCH (SPS) Switchable software for fuel quality and low boost options.   GLOBAL DEVELOPMENT PROGRAMME It all started in late May 2017 in Surberg, Germany when Revos calibration team got their hands on the latest Audi 5 cylinder engine, labelled DAZA by Audi. By travelling to Germany, Revo was able to get a head start on the re-engineering of this platform and get a feel for the potential of this as a performance package going forwards. Based on this initial assessment, Revo ordered their own 8S TTRS whilst continuing development through the Global Development Programme. Over a year in development, covering over 25,000 miles globally on both the RS3 and TTRS which share the 2.5TFSI engine, testing was carried out on 3 vehicles in the UK and 12 vehicles in 6 continents. Involving vehicles in Germany, Croatia, Malta, Australia, Peru, Russia, South Africa, China, Brazil and Mexico, Only Revo operate a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climatic conditions including at altitude, with varying fuel quality and increased humidity. This also allows Revo to test how the Software performs in different driving scenarios including the drag-strip, track and sprint racing and of course, daily driving.   POWER GRAPHS   PERFORMANCE TIMES Performance testing was carried out in Malta with an ambient temperature of 20ºC. 2018 Audi RS3 with DSG transmission. Revo RV019 wheels with road tyres, traction control off and 98RON pump fuel. The average performance times are taken from 5 consecutive runs.   0-60 mph 0-100 mph 30-70 mph 100-200 kph Stock (Tested) 3.85 s 8.82 s - s 9.5 s Revo Stage 1 3.38 s 7.46 s 2.51 s 7.74 s   ADDITIONAL DATA PERFORMANCE DATA Dyno results will vary as the 2.5TFSI Engine is sensitive to heat and fuel quality Catalytic converter efficiency files available through a Revo Authorised Dealer Fuel modes: 95ron, 95 Low Boost, 98ron, 98 Low Boost, 100ron Low Boost option designed to give greater consistency in high-temperature conditions or on Track  TECHNICAL DATA Calibrated Power & Torque Gauges – Full power is shown when the engine reaches full power Improved Sports Mode – Exhaust valves are fully open in Sports Mode Temperature Protection – Re-calibrated thermostatic control to optimise engine cooling RPM Limit Increased (7100RPM) – Limited until oil temperature reaches 60ºC   THE REVO DIFFERENCE OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.

Read more less

2.0T EA888 GEN3 IS38 WITH GPF Revo offer some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy and engine longevity. The Revo tuning philosophy ensures that impressive performance benefits are balanced with useable, reliable power delivery that enhances the way your vehicle drives. Development on the road and racetrack as well as testing in controlled dyno conditions gives you a clearer picture of the performance you can expect from Revo ECU Software. Testing in this way plays an important role in ensuring the highest quality products and delivering the driving experience expected. Stock 300ps  280lbft  REVO Stage 1 Software from 345ps to 370ps  from 339lbft to 368lbft  2.0TSI GEN3 GPF The latest generation 2.0TSI engine has seen some substantial changes in factory form to keep in line with the latest emissions laws. Most notable is the introduction of the GPF (Gasoline Particulate Filter) and the change to the single port injection system. Close monitoring of the GPF system has been an essential step in finding the limitations and tuning potential of the newer DNU* engines. The general consensus is that the GPF not only mutes but limits the engine power, Revo ECU calibration might be reason to dispute that. Enhancing the vehicle with Revo ECU Software gives you much more than just an increase in power and torque. A large part of development is based on drive cycle and driver feedback, our calibration doesn’t just give a great dyno curve and peak power/torque figures but also delivers in feel; giving a smoother yet more responsive feel at low RPM/ partial throttle with huge gains at wide open throttle throughout the whole rev range. Only Revo performance ECU Software maintains factory safety levels and additional driving features. You can switch between three pre-set fuel quality modes depending on the fuel you use; these modes are set through testing our development vehicles in varying climatic conditions with a range of fuel quality throughout the world. The Revo SPS Software Switch is also available separately, can be used to quickly switch between performance modes and access the additional Anti-Theft mode.   SOFTWARE FEATURES SERIAL PORT SWITCH (SPS) Switchable software for stock, performance mode and Antitheft. COLD START PROTECTION Boost is limited until safe oil temperature is reached. TEMPERATURE PROTECTION Enhanced engine cooling and oil temperature management. SPEED LIMIT UNLOCK The top speed limit for this vehicle has been removed.   GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU Software.   POWER GRAPHS   ADDITIONAL FEATURES COLD START PROTECTION For engine oil to work effectively and lubricate your engine it needs time to warm up. When you first start your car, the cold oil is at its thickest, producing higher oil pressure when pumped around the engine putting extra pressure on oil seals. As the engine temperature increases, so does oil temperature. This thins the oil, enabling it to run more freely and better lubricate the moving parts of your engine. Cold Start Protection helps protect engine components by limiting turbo boost based on RPM and oil temperature until it reaches the 80ºC optimum operating level. TEMPERATURE PROTECTION Revo Temperature Protection is an additional safety feature that reduces overall load as the oil temperature passes a set limit. Exhaust gas temperatures (EGT) are also monitored, adapting the operating conditions (Air Fuel Ratio) to ensure they stay within safe parameters. If EGT's reach a set upper limit, then power is automatically reduced until the engine returns to a safe operating temperature. ENHANCED TURBO CONTROL Revo Enhanced Turbine Control offers factory-like protection parameters to avoid over-boost and ensure turbine speeds do not exceed a safe level. GAUGE RECONFIGURATION The gauges on the centre console & instrument cluster have been reconfigured to display a true representation of the increased performance. The stock default values for manifold pressure and engine power have been raised. SWITCHABLE SOFTWARE Using an SPS switch you can take advantage of the switch-ability of Revo software. The Patented OBD2 interface is the ultimate compliment to Revo performance software, giving you the ability to switch between 3 fuel quality modes and an Anti-Theft mode via the vehicle OBD port. SPS Position 1 – Antitheft Mode SPS Position 2 – 95ron Performance Mode SPS Position 3 – 97ron Performance Mode SPS Position 4 – 99ron Performance Mode Simply select a program, plug in, wait a few seconds, remove the SPS device and start the car. It's simple and there's no fixed switch to install in the vehicle. ANTITHEFT MODE As well as the fuel quality modes, Revo software is installed with built in Antitheft Mode. Once the vehicle is put into this mode via the SPS device the engine revs will drop and throttle response will be disabled. The low revs mean the car will struggle to be moved even on the clutch without stalling. Adding an extra level of security to your vehicle. Switch it back to a performance mode and enjoy the drive.   THE REVO DIFFERENCE OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY-BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.  

Read more less

2.0T EA888 GEN3 IS38 WITH GPF Revo offer some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy and engine longevity. The Revo tuning philosophy ensures that impressive performance benefits are balanced with useable, reliable power delivery that enhances the way your vehicle drives. Development on the road and racetrack as well as testing in controlled dyno conditions gives you a clearer picture of the performance you can expect from Revo ECU Software. Testing in this way plays an important role in ensuring the highest quality products and delivering the driving experience expected. Stock 300ps  280lbft  REVO Stage 1 Software from 345ps to 370ps  from 339lbft to 368lbft  2.0TSI GEN3 GPF The latest generation 2.0TSI engine has seen some substantial changes in factory form to keep in line with the latest emissions laws. Most notable is the introduction of the GPF (Gasoline Particulate Filter) and the change to the single port injection system. Close monitoring of the GPF system has been an essential step in finding the limitations and tuning potential of the newer DNU* engines. The general consensus is that the GPF not only mutes but limits the engine power, Revo ECU calibration might be reason to dispute that. Enhancing the vehicle with Revo ECU Software gives you much more than just an increase in power and torque. A large part of development is based on drive cycle and driver feedback, our calibration doesn’t just give a great dyno curve and peak power/torque figures but also delivers in feel; giving a smoother yet more responsive feel at low RPM/ partial throttle with huge gains at wide open throttle throughout the whole rev range. Only Revo performance ECU Software maintains factory safety levels and additional driving features. You can switch between three pre-set fuel quality modes depending on the fuel you use; these modes are set through testing our development vehicles in varying climatic conditions with a range of fuel quality throughout the world. The Revo SPS Software Switch is also available separately, can be used to quickly switch between performance modes and access the additional Anti-Theft mode.   SOFTWARE FEATURES SERIAL PORT SWITCH (SPS) Switchable software for stock, performance mode and Antitheft. COLD START PROTECTION Boost is limited until safe oil temperature is reached. TEMPERATURE PROTECTION Enhanced engine cooling and oil temperature management. SPEED LIMIT UNLOCK The top speed limit for this vehicle has been removed.   GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU Software.   POWER GRAPHS   ADDITIONAL FEATURES COLD START PROTECTION For engine oil to work effectively and lubricate your engine it needs time to warm up. When you first start your car, the cold oil is at its thickest, producing higher oil pressure when pumped around the engine putting extra pressure on oil seals. As the engine temperature increases, so does oil temperature. This thins the oil, enabling it to run more freely and better lubricate the moving parts of your engine. Cold Start Protection helps protect engine components by limiting turbo boost based on RPM and oil temperature until it reaches the 80ºC optimum operating level. TEMPERATURE PROTECTION Revo Temperature Protection is an additional safety feature that reduces overall load as the oil temperature passes a set limit. Exhaust gas temperatures (EGT) are also monitored, adapting the operating conditions (Air Fuel Ratio) to ensure they stay within safe parameters. If EGT's reach a set upper limit, then power is automatically reduced until the engine returns to a safe operating temperature. ENHANCED TURBO CONTROL Revo Enhanced Turbine Control offers factory-like protection parameters to avoid over-boost and ensure turbine speeds do not exceed a safe level. GAUGE RECONFIGURATION The gauges on the centre console & instrument cluster have been reconfigured to display a true representation of the increased performance. The stock default values for manifold pressure and engine power have been raised. SWITCHABLE SOFTWARE Using an SPS switch you can take advantage of the switch-ability of Revo software. The Patented OBD2 interface is the ultimate compliment to Revo performance software, giving you the ability to switch between 3 fuel quality modes and an Anti-Theft mode via the vehicle OBD port. SPS Position 1 – Antitheft Mode SPS Position 2 – 95ron Performance Mode SPS Position 3 – 97ron Performance Mode SPS Position 4 – 99ron Performance Mode Simply select a program, plug in, wait a few seconds, remove the SPS device and start the car. It's simple and there's no fixed switch to install in the vehicle. ANTITHEFT MODE As well as the fuel quality modes, Revo software is installed with built in Antitheft Mode. Once the vehicle is put into this mode via the SPS device the engine revs will drop and throttle response will be disabled. The low revs mean the car will struggle to be moved even on the clutch without stalling. Adding an extra level of security to your vehicle. Switch it back to a performance mode and enjoy the drive.   THE REVO DIFFERENCE OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY-BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.  

Read more less

Stock 300ps  325lbft  REVO Stage 1 Software from 340ps to 355ps  from 395lbft to 415lbft    Revo Software to be installed at our Bradford HQ Once purchased, when fulfilling the order we will contact you to book you into our workshop to have the software installed. If you would like to get booked in quicker please give us a phone call on 0843 289 0182. Stage 1 Performance Software All Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev-range while maintaining the extensive factory safety mechanisms. Although Revo offer some of the most substantial performance increases on the market, peak figures form part of a much bigger picture and are never the sole focus during development. Revo Software offers a perfect balance of performance, economy, longevity and safety. Development and testing of Revo performance software is done in a number of territories around the world, taking into account variations in atmospheric conditions such as altitude and temperature. The Revo R&D process is the most extensive and in-depth in the industry, giving you a product you can trust and an experience you wont forget. Stage 1 software is a must have for any standard RS. With power and torque increases throughout the entire rev range and very smooth power delivery, Revo Software gives the RS the performance it should have had when Ford released it. With adjustable settings for boost, timing and fuelling, the vehicle is set up to suit the conditions, fuel quality and drivers style. Performance increases are significant, and with Revo's linear throttle setup drivability is improved, whether on the road or track.   Research and Development Testing facilities at their UK Headquarters and US Development Facility, as well as a track office at Bruntingthorpe Proving Ground, Revo are able to test their products extensively on and off track. Testing products in this way is paramount to ensuring that along with more useable power and torque comes refined drive-ability, something often overlooked.   On-Road Testing Testing on a dyno will only ever tell part of the story. Revo believe in data-logging on the road and racetrack as well as testing in controlled dyno conditions, to give you a clearer picture of the performance you can expect. This plays an important role in the Revo development process, ensuring the highest quality products that perform where and when it matters most.   Development Vehicles Access to vehicles is imperative to development and testing. Revo run one of the most extensive fleets in the industry, and have access to hundreds of other beta vehicles via a global Authorised Dealer Network. These vehicles not only demonstrates what is capable using Revo products, which cover thousands of miles in a multitude of climates, but also ensures that vehicles perform in any scenario, from a trip to the local shops to an epic adventure in the Alps.   Technical Data Up to 55 bhp and 90 lbft over a stock vehicle   SPS Settings (Software Switching) Setting #1 on your SPS sets your vehicle to stock Setting #2 on your SPS sets your vehicle to Revo Performance mode A (Boost, Fuelling and Timing settings can be configured by your Revo dealer to suit your requirements) Setting #3 on your SPS sets your vehicle to Revo Performance mode B (Boost, Fuelling and Timing settings can be configured by your Revo dealer to suit your requirements) Setting #4 on your SPS sets your vehicle to Revo Performance mode C (Boost, Fuelling and Timing settings can be configured by your Revo dealer to suit your requirements) Setting #5 on your SPS turns ON Anti-Theft mode Setting #6 on your SPS turns OFF Anti-Theft mode   *Valet mode can be set as a performance mode. Can be set using Boost setting 0. Vehicle will run and drive with no boost and a low rev limit of 3500rpm.  **NOTE: Stock mode is not completely stock, it will run similar performance levels to a stock vehicle. Your Revo dealer has a complete factory stock file, if any main dealer warranty or servicing work is required, we recommend returning your vehicle to complete stock.   Software Features SERIAL PORT SWITCH (SPS) Switchable Mapping with adjustable Boost, Fueling and Timing   The Revo Difference OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependent on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.

Read more less

Stock 225ps  236lbft  REVO Stage 1 Software from 260ps to 270ps  from 276lbft to 311lbft   Revo Software to be installed at our Bradford HQ Once purchased, when fulfilling the order we will contact you to book you into our workshop to have the software installed. If you would like to get booked in quicker please give us a phone call on 0843 289 0182. Stage 1 Performance Software All Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev-range while maintaining the extensive factory safety mechanisms. Although Revo offer some of the most substantial performance increases on the market, peak figures form part of a much bigger picture and are never the sole focus during development. Revo Software offers a perfect balance of performance, economy, longevity and safety. Development and testing of Revo performance software is done in a number of territories around the world, taking into account variations in atmospheric conditions such as altitude and temperature. The Revo R&D process is the most extensive and in-depth in the industry, giving you a product you can trust and an experience you wont forget. Stage 1 software is a must have for any standard Focus ST. With power and torque increases throughout the entire rev range and very smooth power delivery, Revo Software gives the ST the performance it should have had when Ford released it. With adjustable settings for boost, timing and fuelling, the vehicle is set up to suit the conditions, fuel quality and drivers style. Driving a Stage 1 ST really puts into perspective how much potential the standard car has, the Revo’d car revs with much greater urgency, using full throttle there’s a push in the back from the new found torque. Power delivery is smooth and progressive; this car eats the road up in a way you wouldn’t expect yet is just as comfortable popping to the shops and driving around town. Performance increases are significant, and with Revo's linear throttle setup drivability is better than standard.   Research and Development Testing facilities at their UK Headquarters and US Development Facility, as well as a track office at Bruntingthorpe Proving Ground, Revo are able to test their products extensively on and off track. Testing products in this way is paramount to ensuring that along with more useable power and torque comes refined drive-ability, something often overlooked.   On-Road Testing Testing on a dyno will only ever tell part of the story. Revo believe in data-logging on the road and racetrack as well as testing in controlled dyno conditions, to give you a clearer picture of the performance you can expect. This plays an important role in the Revo development process, ensuring the highest quality products that perform where and when it matters most.   Development Vehicles Access to vehicles is imperative to development and testing. Revo run one of the most extensive fleets in the industry, and have access to hundreds of other beta vehicles via a global Authorised Dealer Network. These vehicles not only demonstrates what is capable using Revo products, which cover thousands of miles in a multitude of climates, but also ensures that vehicles perform in any scenario, from a trip to the local shops to an epic adventure in the Alps.   Technical Data Up to 45 bhp and75 lbft over a stock vehicle   SPS Settings (Software Switching) Setting #1 on your SPS sets your vehicle to stock Setting #2 on your SPS sets your vehicle to Revo Performance mode A (Boost, Fuelling and Timing settings can be configured by your Revo dealer to suit your requirements) Setting #3 on your SPS sets your vehicle to Revo Performance mode B (Boost, Fuelling and Timing settings can be configured by your Revo dealer to suit your requirements) Setting #4 on your SPS sets your vehicle to Revo Performance mode C (Boost, Fuelling and Timing settings can be configured by your Revo dealer to suit your requirements) Setting #5 on your SPS turns ON Anti-Theft mode Setting #6 on your SPS turns OFF Anti-Theft mode   *Valet mode can be set as a performance mode. Can be set using Boost setting 0. Vehicle will run and drive with no boost and a low rev limit of 3500rpm.  **NOTE: Stock mode is not completely stock, it will run similar performance levels to a stock vehicle. Your Revo dealer has a complete factory stock file, if any main dealer warranty or servicing work is required, we recommend returning your vehicle to complete stock.   Software Features SERIAL PORT SWITCH (SPS) Switchable Mapping with adjustable Boost, Fueling and Timing   The Revo Difference OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependent on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.

Read more less

2.0T EA888 GEN3 IS38 WITH GPF Revo offer some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy and engine longevity. The Revo tuning philosophy ensures that impressive performance benefits are balanced with useable, reliable power delivery that enhances the way your vehicle drives. Development on the road and racetrack as well as testing in controlled dyno conditions gives you a clearer picture of the performance you can expect from Revo ECU Software. Testing in this way plays an important role in ensuring the highest quality products and delivering the driving experience expected. Stock 300ps  280lbft  REVO Stage 1 Software from 345ps to 370ps  from 339lbft to 368lbft  2.0TSI GEN3 GPF The latest generation 2.0TSI engine has seen some substantial changes in factory form to keep in line with the latest emissions laws. Most notable is the introduction of the GPF (Gasoline Particulate Filter) and the change to the single port injection system. Close monitoring of the GPF system has been an essential step in finding the limitations and tuning potential of the newer DNU* engines. The general consensus is that the GPF not only mutes but limits the engine power, Revo ECU calibration might be reason to dispute that. Enhancing the vehicle with Revo ECU Software gives you much more than just an increase in power and torque. A large part of development is based on drive cycle and driver feedback, our calibration doesn’t just give a great dyno curve and peak power/torque figures but also delivers in feel; giving a smoother yet more responsive feel at low RPM/ partial throttle with huge gains at wide open throttle throughout the whole rev range. Only Revo performance ECU Software maintains factory safety levels and additional driving features. You can switch between three pre-set fuel quality modes depending on the fuel you use; these modes are set through testing our development vehicles in varying climatic conditions with a range of fuel quality throughout the world. The Revo SPS Software Switch is also available separately, can be used to quickly switch between performance modes and access the additional Anti-Theft mode.   SOFTWARE FEATURES SERIAL PORT SWITCH (SPS) Switchable software for stock, performance mode and Antitheft. COLD START PROTECTION Boost is limited until safe oil temperature is reached. TEMPERATURE PROTECTION Enhanced engine cooling and oil temperature management. SPEED LIMIT UNLOCK The top speed limit for this vehicle has been removed.   GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU Software.   POWER GRAPHS   ADDITIONAL FEATURES COLD START PROTECTION For engine oil to work effectively and lubricate your engine it needs time to warm up. When you first start your car, the cold oil is at its thickest, producing higher oil pressure when pumped around the engine putting extra pressure on oil seals. As the engine temperature increases, so does oil temperature. This thins the oil, enabling it to run more freely and better lubricate the moving parts of your engine. Cold Start Protection helps protect engine components by limiting turbo boost based on RPM and oil temperature until it reaches the 80ºC optimum operating level. TEMPERATURE PROTECTION Revo Temperature Protection is an additional safety feature that reduces overall load as the oil temperature passes a set limit. Exhaust gas temperatures (EGT) are also monitored, adapting the operating conditions (Air Fuel Ratio) to ensure they stay within safe parameters. If EGT's reach a set upper limit, then power is automatically reduced until the engine returns to a safe operating temperature. ENHANCED TURBO CONTROL Revo Enhanced Turbine Control offers factory-like protection parameters to avoid over-boost and ensure turbine speeds do not exceed a safe level. GAUGE RECONFIGURATION The gauges on the centre console & instrument cluster have been reconfigured to display a true representation of the increased performance. The stock default values for manifold pressure and engine power have been raised. SWITCHABLE SOFTWARE Using an SPS switch you can take advantage of the switch-ability of Revo software. The Patented OBD2 interface is the ultimate compliment to Revo performance software, giving you the ability to switch between 3 fuel quality modes and an Anti-Theft mode via the vehicle OBD port. SPS Position 1 – Antitheft Mode SPS Position 2 – 95ron Performance Mode SPS Position 3 – 97ron Performance Mode SPS Position 4 – 99ron Performance Mode Simply select a program, plug in, wait a few seconds, remove the SPS device and start the car. It's simple and there's no fixed switch to install in the vehicle. ANTITHEFT MODE As well as the fuel quality modes, Revo software is installed with built in Antitheft Mode. Once the vehicle is put into this mode via the SPS device the engine revs will drop and throttle response will be disabled. The low revs mean the car will struggle to be moved even on the clutch without stalling. Adding an extra level of security to your vehicle. Switch it back to a performance mode and enjoy the drive.   THE REVO DIFFERENCE OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY-BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.  

Read more less

STAGE 1 FORD, FOCUS ST (2012 >), 2.0 TURBO | EURO6 Revo Software to be installed at our Bradford HQ Once purchased, when fulfilling the order we will contact you to book you into our workshop to have the software installed. If you would like to get booked in quicker please give us a phone call on 0843 289 0182. Stock 250ps  265lbft  REVO Stage 1 Software from 276ps to 287ps  from 331lbft to 365lbft    Stage 1| Euro6Performance Software The standard 2.0T engine isn’t particularly slow however driving a Revo Stage 1 Focus ST really puts into perspective how much unused potenitial the standard car has. The car revs with greater urgency, using full throttle there's a push in the back from the new found torque. Power delivery is smooth and progressive; this car eats the road up in a way you wouldn't expect. The Revo tuning philosophy really shows through when driving the ST, this is tuning for the real world giving you useable power and torque.   Power Graphs Stock vs Stage 1 - Power BHP Chart* Stock vs Stage 1 - Torque NM Chart*   * All graphs produced with Shell V Power Pump Fuel Software Features ASSISTED LAUNCH Assisted launch recognises when the car is stationary and engages a 2700 RPM hard limit to help you launch your vehicle. A torque limit in 1st gear will also aid you with traction. RPM LIMIT RAISED The standard RPM limit has been raised to 7000 RPM to access more power from the engine. The Revo Difference OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without even opening the bonnet. MONEY BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.    

Read more less

STAGE 1 FORD, FOCUS ST (2012 >), 2.0 TURBO | EURO5 Revo Software to be installed at our Bradford HQ Once purchased, when fulfilling the order we will contact you to book you into our workshop to have the software installed. If you would like to get booked in quicker please give us a phone call on 0843 289 0182. Stock 250ps  265lbft  REVO Stage 1 Software from 276ps to 287ps  from 310lbft to 340lbft    Stage 1 Performance Software All Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev-range while maintaining the extensive factory safety mechanisms. Although Revo offer some of the most substantial performance increases on the market, peak figures form part of a much bigger picture and are never the sole focus during development. Revo Software offers a perfect balance of performance, economy, longevity and safety. Development and testing of Revo performance software is done in a number of territories around the world, taking into account variations in atmospheric conditions such as altitude and temperature. The Revo R&D process is the most extensive and in-depth in the industry, giving you a product you can trust and an experience you wont forget. The standard 2.0T engine isn’t particularly slow however driving a Revo Stage 1 Focus ST really puts into perspective how much unused potenitial the standard car has. The car revs with greater urgency, using full throttle there's a push in the back from the new found torque. Power delivery is smooth and progressive; this car eats the road up in a way you wouldn't expect. The Revo tuning philosophy really shows through when driving the ST, this is tuning for the real world giving you useable power and torque.   Software Features SERIAL PORT SWITCH (SPS) Switchable software for fuel quality and Anti-Theft RPM LIMIT RAISED The standard RPM limit has been raised to 7000 RPM to access more power from the engine. ASSISTED LAUNCH Assisted launch recognises when the car is stationary and engages a 2700 RPM hard limit to help you launch your vehicle. A torque limit in 1st gear will also aid you with traction.   Research and Development Testing facilities at their UK Headquarters and US Development Facility, as well as a track office at Bruntingthorpe Proving Ground, Revo are able to test their products extensively on and off track. Testing products in this way is paramount to ensuring that along with more useable power and torque comes refined drive-ability, something often overlooked.   On-Road Testing Testing on a dyno will only ever tell part of the story. Revo believe in data-logging on the road and racetrack as well as testing in controlled dyno conditions, to give you a clearer picture of the performance you can expect. This plays an important role in the Revo development process, ensuring the highest quality products that perform where and when it matters most.   Development Vehicles Access to vehicles is imperative to development and testing. Revo run one of the most extensive fleets in the industry, and have access to hundreds of other beta vehicles via a global Authorised Dealer Network. These vehicles not only demonstrates what is capable using Revo products, which cover thousands of miles in a multitude of climates, but also ensures that vehicles perform in any scenario, from a trip to the local shops to an epic adventure in the Alps.   Technical Data Up to 37 bhp and75 lbft over a stock vehicle   SPS Settings (Software Switching) Setting #1 on your SPS sets your vehicle to stock* Setting #2 on your SPS sets your vehicle to Revo Performance mode A (Tuned for lower octane pump fuel/poor operating conditions) Setting #3 on your SPS sets your vehicle to Revo Performance mode B (Tuned for high octane pump fuel/good operating conditions) Setting #4 on your SPS sets your vehicle to Anti-Theft mode *NOTE: Stock mode is not completely stock, it will run similar performance levels to a stock vehicle. Your Revo dealer has a complete factory stock file, if any main dealer warranty or servicing work is required, we recommend returning your vehicle to complete stock.   The Revo Difference OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without even opening the bonnet. MONEY BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.  

Read more less

2.0T EA888 GEN3 IS38 WITH GPF Revo offer some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy and engine longevity. The Revo tuning philosophy ensures that impressive performance benefits are balanced with useable, reliable power delivery that enhances the way your vehicle drives. Development on the road and racetrack as well as testing in controlled dyno conditions gives you a clearer picture of the performance you can expect from Revo ECU Software. Testing in this way plays an important role in ensuring the highest quality products and delivering the driving experience expected. Stock 300ps  280lbft  REVO Stage 1 Software from 345ps to 370ps  from 339lbft to 368lbft  2.0TSI GEN3 GPF The latest generation 2.0TSI engine has seen some substantial changes in factory form to keep in line with the latest emissions laws. Most notable is the introduction of the GPF (Gasoline Particulate Filter) and the change to the single port injection system. Close monitoring of the GPF system has been an essential step in finding the limitations and tuning potential of the newer DNU* engines. The general consensus is that the GPF not only mutes but limits the engine power, Revo ECU calibration might be reason to dispute that. Enhancing the vehicle with Revo ECU Software gives you much more than just an increase in power and torque. A large part of development is based on drive cycle and driver feedback, our calibration doesn’t just give a great dyno curve and peak power/torque figures but also delivers in feel; giving a smoother yet more responsive feel at low RPM/ partial throttle with huge gains at wide open throttle throughout the whole rev range. Only Revo performance ECU Software maintains factory safety levels and additional driving features. You can switch between three pre-set fuel quality modes depending on the fuel you use; these modes are set through testing our development vehicles in varying climatic conditions with a range of fuel quality throughout the world. The Revo SPS Software Switch is also available separately, can be used to quickly switch between performance modes and access the additional Anti-Theft mode.   SOFTWARE FEATURES SERIAL PORT SWITCH (SPS) Switchable software for stock, performance mode and Antitheft. COLD START PROTECTION Boost is limited until safe oil temperature is reached. TEMPERATURE PROTECTION Enhanced engine cooling and oil temperature management. SPEED LIMIT UNLOCK The top speed limit for this vehicle has been removed.   GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU Software.   POWER GRAPHS   ADDITIONAL FEATURES COLD START PROTECTION For engine oil to work effectively and lubricate your engine it needs time to warm up. When you first start your car, the cold oil is at its thickest, producing higher oil pressure when pumped around the engine putting extra pressure on oil seals. As the engine temperature increases, so does oil temperature. This thins the oil, enabling it to run more freely and better lubricate the moving parts of your engine. Cold Start Protection helps protect engine components by limiting turbo boost based on RPM and oil temperature until it reaches the 80ºC optimum operating level. TEMPERATURE PROTECTION Revo Temperature Protection is an additional safety feature that reduces overall load as the oil temperature passes a set limit. Exhaust gas temperatures (EGT) are also monitored, adapting the operating conditions (Air Fuel Ratio) to ensure they stay within safe parameters. If EGT's reach a set upper limit, then power is automatically reduced until the engine returns to a safe operating temperature. ENHANCED TURBO CONTROL Revo Enhanced Turbine Control offers factory-like protection parameters to avoid over-boost and ensure turbine speeds do not exceed a safe level. GAUGE RECONFIGURATION The gauges on the centre console & instrument cluster have been reconfigured to display a true representation of the increased performance. The stock default values for manifold pressure and engine power have been raised. SWITCHABLE SOFTWARE Using an SPS switch you can take advantage of the switch-ability of Revo software. The Patented OBD2 interface is the ultimate compliment to Revo performance software, giving you the ability to switch between 3 fuel quality modes and an Anti-Theft mode via the vehicle OBD port. SPS Position 1 – Antitheft Mode SPS Position 2 – 95ron Performance Mode SPS Position 3 – 97ron Performance Mode SPS Position 4 – 99ron Performance Mode Simply select a program, plug in, wait a few seconds, remove the SPS device and start the car. It's simple and there's no fixed switch to install in the vehicle. ANTITHEFT MODE As well as the fuel quality modes, Revo software is installed with built in Antitheft Mode. Once the vehicle is put into this mode via the SPS device the engine revs will drop and throttle response will be disabled. The low revs mean the car will struggle to be moved even on the clutch without stalling. Adding an extra level of security to your vehicle. Switch it back to a performance mode and enjoy the drive.   THE REVO DIFFERENCE OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY-BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.  

Read more less

2.0T EA888 GEN3 IS38 WITH GPF Revo offer some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy and engine longevity. The Revo tuning philosophy ensures that impressive performance benefits are balanced with useable, reliable power delivery that enhances the way your vehicle drives. Development on the road and racetrack as well as testing in controlled dyno conditions gives you a clearer picture of the performance you can expect from Revo ECU Software. Testing in this way plays an important role in ensuring the highest quality products and delivering the driving experience expected. Stock 300ps  280lbft  REVO Stage 1 Software from 345ps to 370ps  from 339lbft to 368lbft  2.0TSI GEN3 GPF The latest generation 2.0TSI engine has seen some substantial changes in factory form to keep in line with the latest emissions laws. Most notable is the introduction of the GPF (Gasoline Particulate Filter) and the change to the single port injection system. Close monitoring of the GPF system has been an essential step in finding the limitations and tuning potential of the newer DNU* engines. The general consensus is that the GPF not only mutes but limits the engine power, Revo ECU calibration might be reason to dispute that. Enhancing the vehicle with Revo ECU Software gives you much more than just an increase in power and torque. A large part of development is based on drive cycle and driver feedback, our calibration doesn’t just give a great dyno curve and peak power/torque figures but also delivers in feel; giving a smoother yet more responsive feel at low RPM/ partial throttle with huge gains at wide open throttle throughout the whole rev range. Only Revo performance ECU Software maintains factory safety levels and additional driving features. You can switch between three pre-set fuel quality modes depending on the fuel you use; these modes are set through testing our development vehicles in varying climatic conditions with a range of fuel quality throughout the world. The Revo SPS Software Switch is also available separately, can be used to quickly switch between performance modes and access the additional Anti-Theft mode.   SOFTWARE FEATURES SERIAL PORT SWITCH (SPS) Switchable software for stock, performance mode and Antitheft. COLD START PROTECTION Boost is limited until safe oil temperature is reached. TEMPERATURE PROTECTION Enhanced engine cooling and oil temperature management. SPEED LIMIT UNLOCK The top speed limit for this vehicle has been removed.   GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU Software.   POWER GRAPHS   ADDITIONAL FEATURES COLD START PROTECTION For engine oil to work effectively and lubricate your engine it needs time to warm up. When you first start your car, the cold oil is at its thickest, producing higher oil pressure when pumped around the engine putting extra pressure on oil seals. As the engine temperature increases, so does oil temperature. This thins the oil, enabling it to run more freely and better lubricate the moving parts of your engine. Cold Start Protection helps protect engine components by limiting turbo boost based on RPM and oil temperature until it reaches the 80ºC optimum operating level. TEMPERATURE PROTECTION Revo Temperature Protection is an additional safety feature that reduces overall load as the oil temperature passes a set limit. Exhaust gas temperatures (EGT) are also monitored, adapting the operating conditions (Air Fuel Ratio) to ensure they stay within safe parameters. If EGT's reach a set upper limit, then power is automatically reduced until the engine returns to a safe operating temperature. ENHANCED TURBO CONTROL Revo Enhanced Turbine Control offers factory-like protection parameters to avoid over-boost and ensure turbine speeds do not exceed a safe level. GAUGE RECONFIGURATION The gauges on the centre console & instrument cluster have been reconfigured to display a true representation of the increased performance. The stock default values for manifold pressure and engine power have been raised. SWITCHABLE SOFTWARE Using an SPS switch you can take advantage of the switch-ability of Revo software. The Patented OBD2 interface is the ultimate compliment to Revo performance software, giving you the ability to switch between 3 fuel quality modes and an Anti-Theft mode via the vehicle OBD port. SPS Position 1 – Antitheft Mode SPS Position 2 – 95ron Performance Mode SPS Position 3 – 97ron Performance Mode SPS Position 4 – 99ron Performance Mode Simply select a program, plug in, wait a few seconds, remove the SPS device and start the car. It's simple and there's no fixed switch to install in the vehicle. ANTITHEFT MODE As well as the fuel quality modes, Revo software is installed with built in Antitheft Mode. Once the vehicle is put into this mode via the SPS device the engine revs will drop and throttle response will be disabled. The low revs mean the car will struggle to be moved even on the clutch without stalling. Adding an extra level of security to your vehicle. Switch it back to a performance mode and enjoy the drive.   THE REVO DIFFERENCE OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY-BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.  

Read more less

2.0T EA888 GEN3 IS38 WITH GPF Revo offer some of the most substantial performance increases on the market, however, only the driven know that peak figures form part of a much bigger picture and are never the sole focus during Revo’s development process; it’s all about the drive. Only Revo offers a perfect balance of performance, economy and engine longevity. The Revo tuning philosophy ensures that impressive performance benefits are balanced with useable, reliable power delivery that enhances the way your vehicle drives. Development on the road and racetrack as well as testing in controlled dyno conditions gives you a clearer picture of the performance you can expect from Revo ECU Software. Testing in this way plays an important role in ensuring the highest quality products and delivering the driving experience expected. Stock 300ps  280lbft  REVO Stage 1 Software from 345ps to 370ps  from 339lbft to 368lbft  2.0TSI GEN3 GPF The latest generation 2.0TSI engine has seen some substantial changes in factory form to keep in line with the latest emissions laws. Most notable is the introduction of the GPF (Gasoline Particulate Filter) and the change to the single port injection system. Close monitoring of the GPF system has been an essential step in finding the limitations and tuning potential of the newer DNU* engines. The general consensus is that the GPF not only mutes but limits the engine power, Revo ECU calibration might be reason to dispute that. Enhancing the vehicle with Revo ECU Software gives you much more than just an increase in power and torque. A large part of development is based on drive cycle and driver feedback, our calibration doesn’t just give a great dyno curve and peak power/torque figures but also delivers in feel; giving a smoother yet more responsive feel at low RPM/ partial throttle with huge gains at wide open throttle throughout the whole rev range. Only Revo performance ECU Software maintains factory safety levels and additional driving features. You can switch between three pre-set fuel quality modes depending on the fuel you use; these modes are set through testing our development vehicles in varying climatic conditions with a range of fuel quality throughout the world. The Revo SPS Software Switch is also available separately, can be used to quickly switch between performance modes and access the additional Anti-Theft mode.   SOFTWARE FEATURES SERIAL PORT SWITCH (SPS) Switchable software for stock, performance mode and Antitheft. COLD START PROTECTION Boost is limited until safe oil temperature is reached. TEMPERATURE PROTECTION Enhanced engine cooling and oil temperature management. SPEED LIMIT UNLOCK The top speed limit for this vehicle has been removed.   GLOBAL DEVELOPMENT PROGRAMME Only Revo operates a Global Development Programme through their network of over 400 Revo Authorised Dealers worldwide. Access to vehicles on this scale enables the calibration team to fine-tune products before release, testing products in a wide range of climates and conditions including altitude, fuel quality, humidity. This also allows Revo to test how Revo products perform in different driving scenarios and formed a vital part in the development of Performance ECU Software.   POWER GRAPHS   ADDITIONAL FEATURES COLD START PROTECTION For engine oil to work effectively and lubricate your engine it needs time to warm up. When you first start your car, the cold oil is at its thickest, producing higher oil pressure when pumped around the engine putting extra pressure on oil seals. As the engine temperature increases, so does oil temperature. This thins the oil, enabling it to run more freely and better lubricate the moving parts of your engine. Cold Start Protection helps protect engine components by limiting turbo boost based on RPM and oil temperature until it reaches the 80ºC optimum operating level. TEMPERATURE PROTECTION Revo Temperature Protection is an additional safety feature that reduces overall load as the oil temperature passes a set limit. Exhaust gas temperatures (EGT) are also monitored, adapting the operating conditions (Air Fuel Ratio) to ensure they stay within safe parameters. If EGT's reach a set upper limit, then power is automatically reduced until the engine returns to a safe operating temperature. ENHANCED TURBO CONTROL Revo Enhanced Turbine Control offers factory-like protection parameters to avoid over-boost and ensure turbine speeds do not exceed a safe level. GAUGE RECONFIGURATION The gauges on the centre console & instrument cluster have been reconfigured to display a true representation of the increased performance. The stock default values for manifold pressure and engine power have been raised. SWITCHABLE SOFTWARE Using an SPS switch you can take advantage of the switch-ability of Revo software. The Patented OBD2 interface is the ultimate compliment to Revo performance software, giving you the ability to switch between 3 fuel quality modes and an Anti-Theft mode via the vehicle OBD port. SPS Position 1 – Antitheft Mode SPS Position 2 – 95ron Performance Mode SPS Position 3 – 97ron Performance Mode SPS Position 4 – 99ron Performance Mode Simply select a program, plug in, wait a few seconds, remove the SPS device and start the car. It's simple and there's no fixed switch to install in the vehicle. ANTITHEFT MODE As well as the fuel quality modes, Revo software is installed with built in Antitheft Mode. Once the vehicle is put into this mode via the SPS device the engine revs will drop and throttle response will be disabled. The low revs mean the car will struggle to be moved even on the clutch without stalling. Adding an extra level of security to your vehicle. Switch it back to a performance mode and enjoy the drive.   THE REVO DIFFERENCE OBD PORT INSTALL Revo Software can be installed quickly and safely via the OBD Port without the need to open the ECU. MONEY-BACK GUARANTEE We know you'll love how Revo Software transforms your car. If you don't, we'll give you your money back. FUEL ECONOMY Dependant on your driving style, this software will deliver like for like fuel economy in 'normal' driving conditions.  

Read more less