Revo Shop

REVO AIR INTERCOOLER 1.8/2.0 TFSI The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow thus decreasing turbulence and increasing airspeed into the bespoke bar and plate core. These features enhance charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures even compared to the Audi S3 (8P) cast aluminium intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment 51% Increased Core Volume over a standard cooler 21% Increased Core Volume over an OE S3 cooler Lower Intake Temperatures INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has a much larger core volume than the OEM part and offers perfect fitment, improving cooling by utilising the full volume of the stock location space as well as cold ambient air from the front of the vehicle. END TANK DESIGN End tanks play an important part in managing pressure drop and work in harmony with the core to promote airflow, the stock ones are inefficiently designed and create turbulent air in corners. These sections create a naturally small cross-sectional flow area, slowing charge air and increasing pressure drop. The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core by removing these turbulent pocket areas found in the OE design. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions from turbulent air pockets found in the OE intercooler. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR AND PLATE CORE Designed with a bar and plate core to maximise the efficiency of heat transfer and minimise flow resistance, the Revo Intercooler easily outperforms similar tube and fin alternatives in both aspects. The Revo Intercooler goes a step farther: featuring carefully specified fin sizing and geometry to further optimise the balance between air cooling and flow restriction. The ambient core side utilises shorter fins with specially designed louvres to slow ambient air passing through the core, which improves heat transfer. While the charge core side features an offset internal fin design to balance surface area and air resistance to aid cooling ability and minimise pressure drop.   SILICONE HOSES Supplied with stronger oil resistant silicone hoses, the Revo Intercooler can be installed using the stock pipework or recommended Revo Intercooler pipework (Coming soon). The internal diameter of each silicone is precisely matched to the inner diameter of the ribbed intercooler inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components.   BRACKETS To ensures precision fitment, Only Revo offers a CNC machined bracket system. Produced to a superior tolerance than that of a cast mounting system, this unique feature also ensures that the supporting brackets are strong and less prone to failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout of the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OE S3 (8P) intercooler with a Revo K04 Kit, Revo production KO4 software, a Revo air intake system and full Eurojet exhaust, the Revo Intercooler was then installed and tested in the same controlled environment to highlight the benefits of it's enhanced cooling. PERFORMANCE DATA Golf GTI TSI EA888 Gen1 with Revo K04 upgrade, OE S3 (8P) intercooler and Revo open cone air intake system and full Eurojet exhaust. Showing the last of five consecutive dyno runs, the efficiency of the Revo Intercooler over the OE S3 intercooler is highlighted. With max gains of +8 HP & +11NM Torque, along with increased performance throughout the entire rev range, the stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, losing no peak power over the 5 runs. INLET TEMPERATURE This is a metric used to confirm that testing on the Revo Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were equal between both coolers, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency advantage. OUTLET TEMPERETURE This graph illustrates the increased cooling performance of the Revo intercooler vs OEM S3 (8P) aluminium intercooler over all five runs. The Revo Intercooler keeps temperatures well below the OE S3 intercooler throughout all 5 runs.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi A3 (8P) 1.8 / 2.0TFSI 2004-2013 Audi S3 (8P) 2.0 TFSI 2006-2012 Seat Altea 1.8 / 2.0 TFSI/TSI 2004-2010 Seat Leon (MK2) 1.8 / 2.0 TFSI/TSI 2004 - 2012 Seat Toledo 1.8 / 2.0 TFSI 2004 - 2009 Skoda Octavia (MK2) 1.8 / 2.0 TFSI/TSI 2004 - 2013 Skoda Superb (B6) 1.8 / 2.0 TSI 2008 - 2013 Skoda Yeti* 1.8 / 2.0 TSI 2010 - 2013 VW EOS 2.0TSI 2006 - 2016 VW Golf (Mk5/6) 1.8 / 2.0 TFSI/TSI 2004 - 2014 VW Jetta (Mk5) 1.8 / 2.0 TFSI 2006 - 2010 VW Scirocco 2.0 TFSI/TSI 2009 - 2014 VW Tiguan* 2.0TFSI 2007-2010 * Yeti / Tiguan fitment for FWD vehciles only. Does not fit AWD.  DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo TFSI Intercooler Instructions NOTES Simple replacement of the OEM part Also available for the MQB Platform

Read more less

REVO INTERCOOLER AUDI TTRS 8S 2.5TFSI The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 55ºC vs. the 8S TTRS intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment with Integrated Crash bar Intercooler Pipes Included Up to 80% Increased Core Volume Over 55ºC Lower AIT   INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has an 80% larger core volume than the OEM part and offers perfect fitment. By integrating a reinforced OE crash bar, it allows access to a volume of unused engine bay space to be filled with the intercooler core. END TANKS DESIGN The stock cast end tanks on the 2.5TFSI cooler do provide elevated performance benefits over the typical plastic end tank coolers. However, the Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. The width of the cooler makes for an extremely large volume end tanks, yielding impressive airflow. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR & PLATE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient airflow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   INTEGRATED CRASH BAR To increase the core size and volume the Revo intercooler has integrated an OEM crash bar, requiring extra provisions within the design to ensure correct fitment and crash bar rigidity. The welded connection has been reinforced with plates to transfer any force away from these areas and adding additional safety factors to the assembly. This also allows the dynamic weight of the intercooler to be distributed through the bar, rather than solely relying on the locating brackets at the bottom of the cooler.   INTERCOOLER PIPE UPGRADED Supplied with an upgraded aluminium mandrel-bent throttle pipe and a 6ply silicone charge pipe. The increased diameter pipework ensures the maximum performance by increasing system volume by over 27%. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components. The throttle hard pipe also includes a water-methanol injection port. RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo Stage 2 software (BETA), a Revo Carbon series air intake system and Milltek downpipe, the Revo Intercooler and pipes were then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA Showing the last of six consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM TTRS intercooler is highlighted. With peak gains of +40 HP & +41NM Torque, along with increased performance throughout the entire rev range. The stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, INLET TEMPERATURE This is a metric used to confirm that testing on the Revo TTRS 2.5TFSI Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were hotter on the Revo Intercooler, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERATURE This is the main performance metric to illustrate that the Revo intercooler far exceeds the stock unit, in fact, one of the most effective Revo intercoolers to date. The graph illustrates the increased cooling performance of the Revo intercooler vs OEM TTRS intercooler over all six runs. The Revo Intercooler provided a massive 57.4°C max and 17.5°C average intake air temperature reduction across the six back to back full gear dyno runs.   INTERCOOLER PRESSURE DROP GRAPH Pressure drop is an important factor when it comes to choosing an Intercooler. The Revo solution features custom cast end tanks to evenly distribute air over the core. This graph highlights that even with massive core size difference there is only a 0.23psi pressure drop in comparison to the stock intercooler, ensuring engine response and minimised turbo lag. You can rest assured that your vehicle will drive and respond as you would expect standard; until you press that pedal!     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi TTRS 2.5 TFSI 2017 onwards DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo TTRS Intercooler Instructions NOTES Simple replacement of the OEM part

Read more less

Only The Driven know that the cooler the air, the more power produced. Revo Intercoolers drastically improve your vehicles ability to cool air compressed by the turbo. Increased volume and surface area, bar and plate cores with end tanks specifically designed to promote even airflow all play a part in lowering temperatures; without negatively affecting pressure. REVO AIR INTERCOOLER MQB 1.8/2.0 TSI EA888 GEN3 The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 36ºC vs. the MQB Golf R intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment Up to 51% Increased Core Volume Over 36ºC Lower AIT INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has much larger core volume than the OEM part and offers perfect fitment, improving cooling by utilising the full volume of the stock location space as well as cold ambient air from the front of the vehicle. END TANK DESIGN The stock end tanks are inefficiently designed and create turbulent air in corners. These sections create a natural flow distribution but slow charge air and increase pressure drop. The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions from turbulent air pockets found in the OE intercooler. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR AND PLATE CORE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient air flow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   SILICONE HOSES Supplied with stronger oil resistant silicone hoses, the Revo Intercooler can be installed using the stock pipework or recommended Revo Intercooler pipework. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components.   BRACKETS To ensures precision fitment, Only Revo offers a CNC machined bracket system. Produced to a superior tolerance than that of a cast mounting system, this unique feature also ensures that the supporting brackets are strong and less prone to failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout of the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo Stage 2 software, a Revo air intake system and Milltek downpipe, the Revo Intercooler was then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA Golf GTI with Revo Stage 2 Software, Golf R intercooler and Carbon Series Front Scoop Showing the last of five consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM Golf R intercooler is highlighted. With max gains of +10 HP & +20NM Torque, along with increased performance throughout the entire rev range, the stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, losing just 2% peak power over the 5 runs compared to 5% on the stock cooler. INLET TEMPERATURE This is a metric used to confirm that testing on the Revo MQB Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were hotter on the Revo Intercooler, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERETURE This graph illustrates the increased cooling performance of the Revo intercooler vs OEM Golf R intercooler over all five runs. The Revo Intercooler keeps temperatures below 49ºC on the fifth run, lower than the stock on its first at 58ºC.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi A3 8V 1.8 / 2.0TSI 2012 > Audi S3 8V 2.0TSI 2012 > Audi TT / TTS 2.0TSI 2015 > Seat Leon 1.8 / 2.0TSI 2013 > Skoda Octavia 1.8 / 2.0TSI 2013 > Skoda Superb 1.8 / 2.0TSI 2015 > VW Golf Mk7 / Alltrack / Sportwagen 1.8 / 2.0TSI 2013 > VW Golf Mk7 GTI / R 2.0TSI 2014 > VW Passat 1.8 / 2.0TSI 2015 > VW Tiguan 2.0TSI 2016 > VW Touran 2.0TSI 2016 > DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo MQB Golf / Octavia / Leon Intercooler Instructions FITTING INSTRUCTIONS Download the Revo MQB A3 / S3 Intercooler Instructions NOTES Simple replacement of the OEM part Also available for the Golf Mk5/6 MLB Platform Will not fit on cars with O2 sensors fitted without interference on the sensor. It is recommended to speak with your dealer before if you are unsure.

Read more less