Intercoolers

TECHNICAL DATA An great upgrade for your modified S3, Perfect for Fast Road and Track use, As fitted to AIRTEC demo car. The Airtec S3 1.8 Turbo Intercooler kit is reasonably priced but high quality alternative from cheap nasty Ebay kits & more than capable of doing the same if not better job than more expensive Intercooler kits, we take a huge amount of pride in making sure our kits are finished to an extremely high standard and we have a real eye for attention for detail. AIRTEC Front mount Intercooler kit Includes these parts & Features 1 x Huge 60mm core Intercooler with flowed cast end tanks, this means less welding and a stronger Intercooler High quality 4/5ply silicon hoses with no joins (Red,Black and Blue) which means better flow inside the pipe work, finished stainless Jubilee clips Stainless horn and ambient temperature support brackets with Airtec logo’s Retains original crash bar ‘requires minor cutting, detailed in instructions’ Retains original fog lights No cutting to bumper Fitting Instructions and all required fixings Requires minor cutting around fog light area of bumper, fog light grilles remain un-cut and detailed in instructions Un-Beatable value for money Proven Power Increase’s for Fast Road & Track Available in Satin Black or Natural Silver Airtec 3 year unlimited mileage warranty Fitting will take 2-3 hours depending on mechanical skill Fits all 1.8T S3 (8L chassis) Amd Rolling Road tested results – Stage 1 remap ‘Higher stages of tune will see even bigger gains’ Standard – Temps Into Intercooler 128 degrees & Out of Intercooler 49 degrees, 12 bhp gain in mid range and standard Intercooler kept losing power AIRTEC Intercooler – Temps Into Intercooler 126 degrees & Out of Intercooler 23 degrees. Please note, above test results taken from Seat Cupra R rolling road testing, it uses same intercooler and pipe work as the Airtec S3 intercooler kit, which means you will get the same great results!

Read more less

TECHNICAL DATA AIRTEC have released their Audi Sport S1 Front Mount Intercooler upgrade to its growing range of performance intercoolers. Audi have made a great job of shoehorning the 2.0 TSI from the Golf GTI into the small chassis of the S1 Unfortunately, due to the size restrictions of the S1, they have made a huge compromise in the intercooler department and the S1 intercooler is a third of the size found in the Golf GTI. Road tests found the standard intercooler was heat soaking (unable to cool the intake temps from turbo) and temperatures rising to 69 degrees which causes the ecu to pull timing out of the map and means a drop in bhp. With the AIRTEC intercooler upgrade fitted, the intake temps didn’t rise above 24 degree’s which means no loss in bhp. Test taken on standard S1 using Snap-on Ethos. We take a huge amount of pride in making sure our kits are finished to an extremely high standard. Why not make your S1 stand out by choosing Super Stealth satin black for a more OEM look or go for the Silver finish for the maximum impact. Great addition to your standard or re-mapped S1. AIRTEC Front mount Intercooler Features 1 x Huge stepped Intercooler core 80mm bottom section and 60mm top section, with flowed cast end tanks, this means less welding and a stronger Intercooler Un-Beatable value for money Proven Power Increase’s for Fast Road & Track Airtec 3 year unlimited mileage warranty Fitting will take 3-4 hours depending on mechanical skill Fits to standard hoses Finished in Pro-Series Satin Black or Natural Silver, please choose from options Optional Airtec logo Approximate sizes 875mm width 200mm height 80mm/60mm thick Airtec Part No: ATINTVAG15

Read more less

TECHNICAL DATA AIRTEC front mount intercooler for the Audi TT 225 only. A great upgrade to any standard or re-mapped Audi TT 225. Comes complete with all alloy hard pipes, Pro Hose silicone hoses and fitting instructions. Comes complete with all alloy hard pipes, Pro silicone hoses and fitting instructions. now only comes in Pro-Series black colour  AIRTEC intercooler sizes: Height 340mm Width 680mm Thickness 60mm Registered Design Right number: 6023257 AIRTEC part no: ATINTVAG14

Read more less

TECHNICAL DATA AIRTEC are proud to introduce the front mount intercooler upgrade for the Audi TT RS (8J). Designed to fit all models, this free-flowing intercooler is a direct replacement for the smaller and more restrictive OEM set up. Featuring a huge 120mm core design together with high-flow, cast end tanks, the AIRTEC intercooler offers much greater surface area, efficiency and volume over standard. Despite this improvement, it fits neatly behind the original bumper and can be used with the original hoses. As with all AIRTEC products, the intercooler was tested back-to-back on the dyno against the OEM item. This showed a huge reduction in air charge temperatures over standard, as seen below: Rolling Road test results – Carried out at AmD Tuning on 11/04/2017 Standard Intercooler: Run 1 – Into intercooler: 117 degrees – Out of intercooler: 69 degrees Run 2 – Into intercooler: 117 degrees – Out of intercooler: 68 degrees Run 3 – Into intercooler: 119 degrees – Out of intercooler: 78 degrees   AIRTEC Intercooler: Run 1 – Into intercooler: 116 degrees – Out of intercooler: 36 degrees Run 2 – Into intercooler: 117 degrees – Out of intercooler: 36 degrees Run 3 – Into intercooler: 118 degrees – Out of intercooler : 37 degrees   The comprehensive fitting kit includes all the correct fixtures and fittings, step-by-step instructions with pictures and should take around 3-4 hours to complete. The intercooler is available in Pro-Series Black finish, with or without the AIRTEC logo. Please note, the original Audi crash bar will need modifying to fit this intercooler upgrade. If you feel your DIY skills are up to the job, this can be cut yourself. Or we can supply a pre-modified crash bar for a charge of £295.   Option 1: Without optional Crash bar – If your DIY skills are up to scratch, why not give it ago yourself Requires existing crash bar to be cut and welded. Option 2: With Crash bar – Modified Crash bar comes powder coated and pre-cut ready to fit – (£295.00)   Features: Designed and manufactured in the UK by AIRTEC AIRTEC logo’d cast end tanks for improved airflow and unbeatable strength Proven reduction in charge temps 3-year unlimited mileage warranty Available in Pro-Series Black AIRTEC logo available at no extra charge Unbeatable value for money! Approximate Dimensions: Width: 540mm Height: 215mm Depth: 120mm AIRTEC part no: ATINTVAG19

Read more less

TECHNICAL DATA Great upgrade for all Corsa D’s with remapped ECU software. Works well on standard cars too! AIRTEC Front mount intercooler kit includes these parts & features 1 x Huge 80mm core Intercooler with flowed cast end tanks, this means less welding and a stronger Intercooler ‘same a VXR design’ High quality 4/5ply silicone hoses with alloy joiners & stainless Jubilee clips Powder coated standard intercooler support brackets Retains original fog lights without any modification Very minor trimming to back of bumper Fitting Instructions and all required fixings Un-Beatable value for money Proven Power Increase’s for Fast Road & Track Available in Satin Black or Natural Silver Airtec 3 year unlimited mileage warranty Fitting will take 2-3 hours depending on mechanical skill Only available in Pro-Series Black AIRTEC part no: ATINTVAUX8

Read more less

TECHNICAL DATA Designed to work with re-mapped Ecu for best results Finished In Pro-Series Satin Black or Natural Silver Removes restrictive OE Vauxall Intercooler, which suffers from heat soak on tuned cars. Great upgrade for all 1.4T with remapped ECU, perfect for Fast Road and Track use. AIRTEC has released their Corsa E 1.4T intercooler upgrade combing great quality at a reasonable price. AIRTEC Front mount Intercooler kit Includes these parts & Features 1 x Huge 80mm core intercooler with flowed cast end tanks, this means less welding and a stronger intercooler, utilising the same design as our replacement for the VXR. High quality 4/5ply silicon hose’s with alloy joiners & stainless Jubilee clips Powder coated standard intercooler support brackets Retains original fog lights without any modification Very minor trimming to back of bumper Fitting Instructions and all required fixings Un-Beatable value for money Proven Power Increase’s for Fast Road & Track Available in Pro-Series Black Airtec 3 year unlimited mileage warranty Fitting will take 2-3 hours depending on mechanical skill Registered Design Right number: 6023249 AIRTEC part no: ATINTVAUX9

Read more less

Replaces very restrictive original twin intercooler setup with lengthy pipework, with an AIRTEC design high flow 60mm core intercooler and a shorter alloy boost pipe kit. We keep fast turbo spool up by using 50mm pipework from turbo to intercooler and 60mm out of the intercooler to help match the throttle body, this combination gives fast turbo spool up coupled with maximum power output. Dyno test results – results taken from Fiat 500 Abarth, fitted with cat back exhaust and AIRTEC FMIC Run 1.  120 degree into the intercooler and 22 degree out of the intercooler Run 2.  122 degree into the intercooler and 22 degree out of the intercooler Run 3.  123 degree into the intercooler and 22 degree out of the intercooler The AIRTEC intercooler dropped the intake tempertures by 100 degree on each run and did not suffer from heat soak Features:     60mm thick proven bar and plate core, spec’d to AIRTEC design     AIRTEC branded cast end tanks for improved air flow and unbeatable stength     Dyno proven to provide lower intake temps and gain BHP     Shorter charge pipes than standard twin intercooler set-up, shorter pipes mean faster turbo spool up     Fitting takes approximately 2-3 hours     3 year unlimited mileage warranty     Available in Pro-Series Black     AIRTEC Logo available at no extra charge     Unbeatable value for money   Will fit any Abarth with Garrett GTI446 Turbo – 165, 180 & 190 bhp models Will fit the following: Series 3 180 Competizione (Mid-Late 2015)Series 4 TurismoSeries 4 Competizione Approximate dimensions: Height – 205mm Width – 820mm Depth – 65mm   Registered Design Right number 6023445

Read more less

AIRTEC Front mount Intercooler Features  1 x single pass 50mm core Intercooler with flowed end tanks, this means less welding and a stronger Intercooler Comes with full fitting instructions & pipe work  Un-Beatable value for money Available in Satin Black or Polished Alloy AIRTEC 3 year unlimited mileage warranty Fitting will take 1-2 hours depending on mechanical skill Will require some small cutting of the bumper and grill area. Finished In Pro-Series Satin Black or Natural Silver   Proven vertical 50mm core, runs top to bottom of the end tanks this gives the single pass design intercooler the shortest route for the charged air to pass though, with such a small turbo, the faster the charged air can get in & out the better. Another great must have with our design is making full use of the hottest part of the intercooler, which is the top section, this is on full show allowing maximum Airflow. Tip, more of the grill can be opened up with Dremel or Drill to allow even more Airflow to the intercooler, we suggest to do this whilst fitting. This intercooler will fit the 1.6 Diesel Mk7 PRE-FACELIFT Fiesta.   AIRTEC part number: ATINTFO36/PRE

Read more less

TECHNICAL DATA AIRTEC has now added a great addition to it’s growing range of performance intercoolers, in the way of this upgraded intercooler for the Volkswagen Golf VI, 2.0 Common Rail Please note: This intercooler will only fit the 2.0L CR engine not PD. Great addition to any standard or re-mapped Golf. AIRTEC Front mount Intercooler kit Includes these parts & Features 1 x Huge 60mm core Intercooler with flowed cast end tanks, this means less welding and a stronger Intercooler. High quality gloss black silicon hoses which means better flow inside the pipe work, finished stainless Jubilee clips. Retains original crash bar. Retains original fog lights. No cutting to bumper. Fitting Instructions and all required fixings. Proven Power Increase’s for Fast Road & Track. Available in Satin Black or Natural Silver. Airtec 3 year unlimited mileage warranty. Fitting will take 2-4 hours depending on mechanical skill. Fits all Mk6 CR140 Golf. This is essential for hotter climate countries. Approximate Dimensions Width – 740mm ‘not including pipe’ Height – 170mm Thick – 70mm Registered Design Right number: 6023454 AIRTEC part no: ATINTVAG21

Read more less

AIRTEC Motorsport front mount intercooler upgrade for the Hyundai I30N. This freer-flowing intercooler is a direct replacement for the smaller and more restrictive OEM set up. It features a stepped twin-core (160mm and 70mm) design for maximum frontal area in the limited space provided behind the bumper. Together with high-flow, moulded one-piece cast end tanks, the AIRTEC intercooler offers much greater efficiency and volume over standard.   TECHNICAL DATA AIRTEC Motorsport front mount intercooler upgrade for the Hyundai I30N.This freer-flowing intercooler is a direct replacement for the smaller and more restrictive OEM set up.It features a stepped twin-core (130mm and 40mm) design for maximum frontal area in the limited space provided behind the bumper. Together with high-flow, moulded one-piece cast end tanks, the AIRTEC intercooler offers much greater efficiency and volume over standard. With a 70mm cold side, this makes the AIRTEC intercooler the largest on the market currently for the Hyundai I30N! Despite this improvement, it fits neatly behind the original bumper, requires no trimming or cutting. The comprehensive fitting kit includes all the correct fixtures and fittings, step-by-step instructions with pictures, mew Pro-Hoses silicone hoses and should take around 2-3 hours to complete. The intercooler is available in Pro-Series Black finish and either with or without the AIRTEC logo and Gloss Black Pro silicone hoses. Approx. dimensions:– 160mm deep bottom core and 70mm deep top core– 195mm high– 610mm wide Intercooler test data: Features:Stepped intercooler design for maximum flowDesigned and manufactured in the UK by AIRTECAIRTEC CAD designed cast end tanks for improved airflow and unbeatable strengthReduced charge temps3-year unlimited mileage warrantyAvailable in Pro-Series black finishAIRTEC logo available at no extra chargeUnbeatable value for money! Choose from plain black, or add your choice of coloured AIRTEC logo free of charge. AIRTEC Part No: ATINTHYU1 Registered Design Right number: Pending

Read more less

TECHNICAL DATA Bolt on BHP, by lowering the charge Air temperatures, a remapped car has increased power by ecu changes that raise boost pressure and other parameters, this increase in boost pressure raise intake temps and power loss soon follows, by fitting an up-rated intercooler you lower these intake temps, in turn increasing bhp and making your engine safer Dyno testing – tests were carried out for temperature before and after the intercooler Stock intercooler Run 1 – Into intercooler 137 degrees C – Out of intercooler 50 degrees C Run 1 – Into intercooler 139 degrees C – Out of intercooler 54 degrees C Run 1 – Into intercooler 141 degrees C – Out of intercooler 61 degrees C Airtec intercooler Run 1 – Into intercooler 138 degrees C – Out of intercooler 26 degrees C Run 1 – Into intercooler 140 degrees C – Out of intercooler 27 degrees C Run 1 – Into intercooler 141 degrees C – Out of intercooler 27 degrees C Airtec F56 features Race spec bar ‘n’ plate core 60mm thick for super-fast recovery times Dyno proven to reduce intake temperatures Super flow end tanks – thin wall cast alloy end tanks with no sharp corners that can slow air speed Bolt on design with no extra modding required Airtec’s 3 year unlimited mileage warranty CNC alloy pipe connections Approximate Dimensions: 800mm width 210mm height 60mm thickness only available in  pro-series black Also tested and proven by DervTech F56 MINI Cooper S / Challenge 210, 300hp, 330lbft!! +70hp and +90lbft. Please note: This intercooler will not fit the JCW   Registered Design Right number: 6023250 AIRTEC part number: ATINTMINI05

Read more less

Bolt on BHP, by lowering the charge Air temperatures, a remapped car has increased power by ECU changes that raise boost pressure and other parameters, this increase in boost pressure raise intake temps and power loss soon follows, by fitting an up-rated intercooler you lower these intake temps, in turn increasing bhp and making your engine safer.   TECHNICAL DATA Bolt on BHP, by lowering the charge Air temperatures, a remapped car has increased power by ECU changes that raise boost pressure and other parameters, this increase in boost pressure raise intake temps and power loss soon follows, by fitting an up-rated intercooler you lower these intake temps, in turn increasing bhp and making your engine safer AIRTEC F56 features Race spec bar ‘n’ plate core for super-fast recovery times Super flow end tanks – thin wall cast alloy end tanks with no sharp corners that can slow air speed Bolt on design with no extra modding required Only manufacturer offering the important air ram guides! AIRTEC’s 3 year unlimited mileage warranty CNC alloy pipe connections Approximate dimensions Thickness 140mm wide stepped core Height 230mm (the 140mm thick core section is 180mm high) Width 810mm Currently the only manufacturer offering the all-important air ram guides. Available pro-series black only  Registered Design Right number: 6023446 AIRTEC part no: ATINTMINI06

Read more less