Oil Coolers

Following an extensive development process, AIRTEC Motorsport are proud to launch our oil cooler kit aimed at FK2 Civic Type R owners who require the ultimate cooling package to maintain steady running temperatures on track or fast road use. The ChallengeWhen modifying the FK2 Civic Type R to increase power and torque, an unavoidable by-product is the additional heat level that’s transferred to the car’s cooling system. During sustained hard use, this can become a substantial issue, as temperatures can increase enough to trigger the ECU’s safety features, reducing torque or even putting the car into a limp mode.  The SolutionDeveloped in-house at AIRTEC HQ in the UK we designed an oil cooler to help address the cooling issues when pushed hard. This cooler fits neatly behind the fog light (requires removal) and utilises our bespoke CAD-modelled air duct to force cold air through the core. To create a flow path and further improve cooling, air then exits via the inner arch liner (requires cutting). A pre-cut mesh shield is supplied for both the front and rear to protect the radiator from road debris damage. This can fit with our intercooler and auxiliary radiator/turbo cooler to create the ultimate cooling package. The comprehensive kit also features laser-cut and powder-coated brackets, high-quality braided lines with AN fittings as well as all fixtures and fittings, and detailed fitting instructions. Tested on Track20th June 2025 – Cadwell Park CircuitTest car fitted with air filter and Stage 1 remap producing a dyno proven 375bhpData logged via OBD port using Torque Pro app data recording and downloaded to PC. Run 1 – 10.00am – Ambient Temperature: 24°C – 15 minute session – Maximum Oil Temperature: 106°C Run 2 – 10:45am – Ambient Temperature: 25°C – 20 minute session – Maximum Oil Temperature: 112°C  Run 3 – 11:30am – Ambient Temperature: 27°C – 15 minute session – Maximum Oil Temperature: 112°C Run 4 – 12:00pm – Ambient Temperature: 28°C – 20 minute session – Maximum Oil Temperature: 114°C  Run 5 – 2.00pm – Ambient Temperature: 29°C – 15 minute session – Maximum Oil Temperature: 118°C Run 6 – 2:45pm – Ambient Temperature: 30°C – 20 minute session – Maximum Oil Temperature: 117°C Run 7 – 3:30pm – Ambient Temperature: 28°C – 15 minute session – Maximum Oil Temperature: 113°C  Driver Comments: “This was an extremely hot day and car coped very well. Before the auxiliary radiator and oil cooler were installed I would normally get approximately 5 to 6 laps, which is about 8 to 10 minutes of hard use before the oil temperature rose to around the 126 to 128°C. With the coolers installed, I can run at least 10 to 14 laps, which is over 20 minutes of hard use, and oil temperatures don’t normally go above 115°C. Also a major advantage is that I can repeat that all day long, whereas before I found that once the temperature of the oil got really hot it would normally not cool down enough for the rest of the day,  so it meant I ended up doing only 3 to 4 laps before the temperature rose again, as the oil never fully cooled down and seemed to heat back up quicker.” Features: Designed and developed specifically for the FK2 Civic Type R Improves oil cooling ability – tested on track and proven to work Utilises our bespoke CAD-modelled air duct Ducting channels air in and allows it to exit via arch liner Bespoke laser-cut and powder coated brackets High-quality braided lines with AN fittings Fits with our intercooler and auxiliary radiator/turbo cooler kit to create the ultimate cooling package Comprehensive kit with all fixtures, fittings and instructions AIRTEC part no: ATMSHON7

Read more less

  Fitment Audi    A6 (C7)   A6 (C6)   Q7 (4L 05-15)   Q5 (B8)   A8   S4 (B8)   S5 (B8) Volkswagen    Touareg (Mk3 20-) From the factory, Audi's 3.0T engine is equipped with a plastic thermostat housing. While sufficient when new, its plastic construction is prone to degradation over time. After enduring thousands of heat cycles and consistent exposure to chemical-rich antifreeze, the housing becomes brittle and begins to crack. Once the material is compromised, it can lead to a significant coolant leak, which, if left unchecked, may result in overheating and severe engine damage. This is especially problematic for the supercharged 3.0T, where maintaining proper engine temperature is critical for both performance and longevity. Our engineers set out to fix this issue with the ECS Billet Aluminum Thermostat Upgrade, engineered for enhanced durability, efficiency, and reliability. This precision-machined 6061 T6 billet aluminum thermostat replaces the failure-prone factory plastic housing, addressing one of the most common failure modes for all 3.0T supercharged engines. Designed with both performance and longevity in mind, this thermostat is the ultimate solution to overheating and coolant leaks, offering peace of mind in everyday driving and high-performance applications. The ECS Billet Aluminum Thermostat is the perfect choice for Audi 3.0T owners looking to enhance cooling system durability and reliability while eliminating the weaknesses of the OEM design. Take control of your engine’s performance and longevity today! PERFORMANCE FEATURES Our 6061-T6 billet aluminum housing is engineered for superior strength and reliability, offering exceptional resistance to cracking and warping. A striking red anodized finish provides corrosion resistance while adding a sleek aesthetic to your engine bay. The billet aluminum thermostat fin assembly features DLC (diamond-like coating) to reduce friction in thermostat operation, ensuring smooth and reliable performance. The internal return spring features a durable Zinc coating for exceptional longevity and corrosion resistance.  Our proprietary scraper seal is constructed from high-quality Viton rubber, providing a secure, leak-free seal for optimal cooling system performance. The ECS Billet Aluminum Thermostat Upgrade comes with an 80°C thermostat pre-installed for ease of assembly. BENEFITS Fixes Common Failure Modes: Eliminates the risk of cracking, leaking, and other issues associated with the OE plastic thermostat housing. Enhanced Cooling Performance: Maintains stable engine temperatures, even under demanding street or track conditions. Dual-Purpose Design: Built for high-performance enthusiasts while offering reliability for daily drivers. PRODUCT DEVELOPMENT Our ECS 3.0T Billet Aluminum Thermostat Upgrade was designed, engineered, tested, and quality inspected by our Research and Development team in our Wadsworth, Ohio facility. We strive for the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Read more less

As part of our expanding Mk4 Focus platform product range, AIRTEC Motorsport is proud to launch our oil cooler kit for the ST 2.3-litre model. Developed in-house at AIRTEC HQ in the UK, we’ve created a comprehensive solution to improving the car’s oil cooling ability for modified Mk4 ST owners who struggle to maintain steady oil temperatures on track, or during fast road use. With vast experience in developing uprated oil cooler packages for a variety of modified track and road cars, the challenge with this kit was to integrate a large capacity, external oil cooler neatly behind the upper grille area without obstructing the air intakes. As a result, our design includes a designated scoop on the left-hand side that supports the oil cooler and channels cold air towards the intakes. The package also includes an AIRTEC Motorsport oil cooler, bespoke laser-cut and powder coated brackets, high quality braided hose lines with Aerotec fittings, a thermostat-controlled sandwich plate and all fixtures and fittings, including instructions for a bolt-on installation. The kit is designed to integrate seamlessly with the car’s existing features and requires no drilling or cutting, so is completely reversible if need be. Its improved cooling efficiency and easy fitment makes it an essential modification for all modified Mk4 Focus ST models. Features: Comprehensive kit designed specially for the Mk4 Focus ST platform Reduces temperatures on track and road Scoop directs constant feed of cold air to the intake Designed and developed in the UK No cutting or drilling required to fit Proven AIRTEC large capacity external oil cooler Bespoke laser-cut and powder coated brackets High-quality hoses and fittings Includes all fixtures and detailed instructions

Read more less

As part of our expanding Mk8 Fiesta platform product range, AIRTEC Motorsport is proud to launch our oil cooler kit for the ST model. Developed in-house at AIRTEC HQ in the UK, we’ve created a comprehensive solution to improving the car’s oil cooling ability for modified Mk8 ST owners who struggle to maintain steady oil temperatures on track, or during fast road use. With vast experience in developing uprated oil cooler packages for a variety of modified track and road cars, the challenge with this kit was to integrate a large capacity, external oil cooler neatly behind the front bumper. However, the Mk8 Fiesta has very limited available space directly behind the open grille area, which meant we developed an innovative solution that mounts the oil cooler in front of the right-hand side arch liner and is fed a constant flow of cool air by an air feed duct that’s included in the kit. The package also includes a AIRTEC Motorsport oil cooler, bespoke laser-cut and powder coated AIRTEC brackets, high quality braided hose lines with Aerotec fittings, a thermostat-controlled sandwich plate and all fixtures and fittings, including instructions, for a simple bolt-on installation. The kit is designed to integrate seamlessly with the car’s existing features and requires no drilling or cutting, so is completely reversible if need be. Its improved cooling efficiency and easy fitment makes it an essential modification for all modified Mk8 ST models. Features: Comprehensive kit designed specially for the Mk8 Fiesta ST platform Reduces temperatures on track and road Front intake directs constant feed of cold air to the filter Designed and developed in the UK No cutting or drilling required to fit Proven AIRTEC large capacity external oil cooler Bespoke laser-cut and powder coated brackets High-quality hoses and fittings Includes all fixtures and detailed instructions AIRTEC Part No: ATMSFO129

Read more less

2.0 TSI DSGgearbox oil cooler ​ For DQ 250 6-speed and DQ381 7-speed It's not just your engine oil that you need to protect. Your DSG gearbox is very susceptible to overheating, leading to protection mode that reduces engine power and eventually prevents gear selection. Why fit theDSG oil cooler kit? Our unique DSG Oil Cooler Kit is an essential fit for any hard-driven MQB 2.0 TSI car running high power levels or in hot climates. It's a complete ready to install package, using a clever sandwich plate design for straightforward and completely reliable installation.   Transferring more power and torque through the DSG gearbox generates ever more heat to dissipate.  Significantly increased oil temperatures means only one thing: a decrease in the ability for your DSG box to stay properly cooled, eventually causing power drop and gear selection issues.  Under hard driving, the factory DSG oil/water cooler is easily overwhelmed. Problems start to occur when oil cannot dissipate its collected heat fast enough and the oil begins to thin and degrade - losing its lubrication properties. When this happens, the DSG will protect itself and begin to lower the engine torque, increase shift times and eventually loose gear selection. ooThe RacingLine kit solves this problem: by adding in an additional air/oil cooler positioned right in the airflow at the front of the car, oil temperatures are reduced by around 15  - 20   degrees centigrade (of course dependant on how the car is being used, ambient temps and state of tune). The kit uses a clever design which retains the factory oil/water cooling and adds to it with the thermostatically-controlled front-mounted cooler - doubling up your cooling capability when it's needed with less heat transfer into the water system. Only when the oil exceeds normal temperatures, the thermostat opens. Oil temperature then drops significantly as it is pumped through the densely packed fins of the 10-row cooler’s large surface area mounted right in the cool airflow. HIGH EFFICIENCY COOLER Our 10-row stacked plate design efficiently forces the hot oil through a series of aluminium pressed plates. Heat dissipates as cold air moves across the plates. 210 SERIES BRAIDED HOSE Our oil lines feature an attractive outer nylon braid strengthened by a stainless steel inner weave for maximum resilience. Protective external sheath avoids any rubbing damage in use.   TEMPERATURE CONTROL Our unique adaptor block oil take-off includes a clever internal thermostatic-control valve to direct oil flow through the cooler only when temperature hits 82°c/180°F. COLD AIR LOCATION The front-mount location brackets of the RacingLine cooler kit places it in the optimum airflow and ensures that oil temperature drops and excess heat is funnelled out efficiently. PRECISION MACHINED Precision machined billet components utilising the latest 5 Axis CNC machines for perfect accuracy, first time, every time.  LOW PROFILE COOLER The kit includes a replacement factory-spec oil/water cooler with a lower height, allowing for easy fitment without affecting the battery tray above it. CONFIRMED APPLICATIONS VWR29G7250 / DQ250 6-SPEED GEARBOXES ONLY * VWR29DQ381 / DQ381 7-SPEED GEARBOXES ONLY ​ *not for US-spec DQ250 with Secondary Air Intake (SAI) system > VW Golf 7 & 7.5 GTI & Clubsport 2013-2020 > VW Golf 7 & 7.5 R 2013-2020 > VW Golf 7 & 7.5 1.8 TSI 2013-2020 > VW Passat 2.0 TSI B8 2015+ > VW Arteon 2.0 TSI 2017+ > VW T-Roc R 2.0 TSI 2019+ > VW Tiguan II 2.0 TSI 2016+ > VW Jetta / GLI 7 2018+ > Audi S3 8V 2013-2020 > Audi A3 2.0 TSI / 1.8 TSI 8V 2013-2020 > Audi TT 3 8S 2014+ > Audi TTS 2.0 TFSI 8S 2015-2021 > Audi TT 2.0 TFSI 8S 2014+ > Audi TTS 2.0 TFSI 8S 320ps (EA888.4) 2021+ > Audi SQ2 2018+ > SEAT Leon III Cupra 5F 2014-2020 > SEAT Leon III 1.8 TSI 5F 2014-2020 > Cupra Ateca 2018+ > Skoda Octavia III vRS 2.0 TSI 5E 2014-2020 > Skoda Superb III 1.8 / 2.0 TSI 3V 2015+   DSG COOLER  FITMENT. As you’d expect, the RacingLine DSG Oil Cooler is a beautifully detailed complete kit, developed exclusively for MQB cars with either DQ250 6-speed or DQ381 7speed DSG gearbox.   The system is designed for straightforward fitting and ultimate reliability. Everything needed for perfect fitment is included.  Unlike other DSG oil cooler kits, the RacingLine package keeps the oil/water cooler and adds to it with the oil/air cooler 10 row stacked-plate oil cooler radiator, flowed to obtain maximum heat dissipation without undue pressure drop Optimum front mounted location behind left side front lower grill aperture with all necessary brackets and fixing kit supplied 210 Series stainless steel, nylon braided feed and return lines run past the chassis leg into the bumper cavity, then connecting to the oil cooler core DOUBLE COOLING. Our DSG Cooler design is a unique design: it retains the factory oil/water gearbox cooling system, plus adds our oil/air cooling as well. Why? The DSG oil will still quickly warm up from the hot water in the engine's coolant system, reaching full operating temperature as soon as possible. But that's where the problem begins on a hard-driven car. The hot engine coolant will now have little to no cooling effect on the DSG oil, and gearbox temps start to rise rapidly. That's the point at which our sophisticated thermostatic control valve inside the adaptor block will then divert hot oil out to the new 10-row cooler located in the cool fresh air flow. After the cooled transmission oil returns from the cooler, it carries less heat to be absorbed into the engine coolant system - helping control all the temperatures under the bonnet. Our replacement oil/water cooler (that's the silver part in the picture) is lower in height than the factory one. So the total height of both parts still fits perfectly under the battery location above it.  WHAT'S IN THE KIT?Oil cooler mounting brackets  AN10 210 series Nylon braided feed and return line Billet CNC thermostatic adaptor block Replacement, low-profile oil/water cooler AN10 10-row oil/air cooler core Fitting kit containing all necessary nuts, bolts, washers and rubber mounting bobbins BRACKET SETS The kit for all MQB cars comes supplied with two bracket kits. One kit is for Audi S3 models, the other is for all Golf 7 and other MQB models.  ​ Mounting for the bracket set requires drilling bolt holes through the front crash bar. GOLF 7 & 7.5 PLUS OTHER MQB MOUNTING AUDI S3 8V MOUNTING WHAT'S THE PROBLEM ON TRACK? When oil temperature reaches 138°C/280°F, the DSG's control system initiates a reduction in engine torque, meaning a serious drop in performance.   Carry on driving, and if temperatures then rise above 145°C/293°F, your DSG clutches no longer get the fluid pressure they require and you loose drive altogether as the box goes into a safety mode. ​ If you're in a hot climate this can happen after only about 15 minutes at the track - meaning a long wait while your gearbox cools down again. PRECISION ENGINEERED FOR PERFECT PERFORMANCE. Sophisticated thermostatic control adaptor block to divert oil flow around new cooling system - but only when needed Billet gloss-anodised for long-lasting protection and good looks Oil lines with protective outer nylon braid strengthened by a stainless steel inner weave for maximum resilience.  T6 6061 CNC aluminium used throughout for precision accurate fit 10-row stacked plate-design cooler efficiently forces the hot oil through a series of aluminium pressed plates.

Read more less

AIRTEC Motorsport Oil Cooler Kit for Honda Civic FK8 Type R As part of our expanding Honda Civic FK8 Type R product range, AIRTEC Motorsport is proud to launch our oil cooler kit suitable for track or fast road use. AIRTEC part no: ATMSFK802 TECHNICAL DATA AIRTEC Motorsport Oil Cooler Kit for Honda Civic FK8 Type R As part of our expanding Honda Civic FK8 Type R product range, AIRTEC Motorsport is proud to launch our oil cooler kit suitable for track or fast road use. Following an extensive development process, AIRTEC Motorsport are proud to launch its new oil cooler kit aimed at modified Type R for track or fast road use. Our kit has been designed in the UK after thorough research and huge experience in developing uprated oil cooler packages for a variety of modified track and road cars. With limited space, the challenge with this kit was to integrate a large capacity, external oil cooler neatly behind the bumper where it could still benefit from a direct airflow, whilst integrating seamlessly with the car’s existing fixtures and fittings with no drilling or cutting required. As a result, we have developed a kit that is completely reversible if need be. The comprehensive package includes a tried and tested 13-row AIRTEC oil cooler, bespoke laser-cut and powder-coated AIRTEC bracket, high quality braided hose lines with Aerotec fittings, and all fixtures, including instructions, for a simple bolt-on installation. To ensure the maximum amount of air flow, we recommend removing the near side fog light and/or installing the exit vent into the wheel arch liner to provide better flow. However, these are not essential and the oil cooler will still work fine using the bumper’s original intake slots. Its increased cooling efficiency and easy fitment makes it an essential modification for all modified FK8 Type R models. Key features: Designed and developed in the UK Reduces temperatures on track and road Proven AIRTEC large capacity oil cooler Bespoke laser-cut and powder-coated brackets High-quality hoses and fittings Comprehensive kit with all fixtures, fittings and instructions Registered Design Right number: AIRTEC part no: ATMSFK802

Read more less

Following an extensive development process, AIRTEC Motorsport are proud to launch its new oil cooler kit aimed at modified Yaris GR owners who struggle to maintain steady oil temperatures on track, or during fast road use. AIRTEC Part No: ATMSYGR04 TECHNICAL DATA AIRTEC Motorsport Oil Cooler Kit for Toyota Yaris GR. Following an extensive development process, AIRTEC Motorsport are proud to launch its new oil cooler kit aimed at modified Yaris GR owners who struggle to maintain steady oil temperatures on track, or during fast road use. Our kit has been designed in the UK after thorough research and huge experience in developing uprated oil cooler packages for a variety of modified track and road cars. The challenge with this kit was to integrate a large capacity, external oil cooler mounted neatly behind the grille for direct airflow, whilst integrating seamlessly with the car’s existing fixtures and fittings with no drilling or cutting required. As a result, we have developed a kit that is completely reversible if need be. The comprehensive package includes a tried and tested 13-row AIRTEC oil cooler, bespoke laser-cut and powdercoated AIRTEC brackets, high quality braided hose lines with Aerotec fittings, and all fixtures, including instructions, for a simple bolt-on installation. Its cooling efficiency and easy fitment makes it an essential modification for all modified Yaris GR’s. Key features: Designed and developed in the UK No cutting or drilling required to fit Reduces temperatures on track and road Proven AIRTEC large capacity external oil cooler Bespoke laser-cut and powder coated brackets High-quality hoses and fittings Comprehensive kit with all fixtures, fittings and instructions Registered Design Right numbers:  AIRTEC part no: ATMSYGR04

Read more less

Developed from our direct involvement within the BTCC and Mini Challenge race series where we have provided race proven cooling packages, we have directly transferred our knowledge from this over to our road going products. FMOC11 has been developed with the same engineering expertise that is applied to our Mini Challenge Oil coolers, these see extensive driving over the race season calendar, so we are proud to give the I30N the same motorsport treatment. Lowering your oil temps on and off the track whilst providing a product that does not skimp on quality, so much so that it is backed by our Forge Lifetime Guarantee* With our extensive range of performance parts out on the market allowing the limits of the i30N/Veloster N to be pushed in the chase for top power gains, the addition of power and speed creates heat. Rising oil temperatures will result in only one outcome, a reduction of sufficient lubrication of your engines internal components. Therefore, the FMOC11 is a must have product for the keen driver, the location of the oil cooler radiator at the front of the vehicle’s radiator grill allows for superior air flow. During our development of this product we have seen oil temperatures reduced significantly. The Hyundai oil cooler has its inlet and outlets placed in the correct position for optimum flow , when oil coolers are fitted upside-down this can lead to cavitation (air locks) within the system, this can over a prolonged period of time lead to engine fatigue and potentially internal component damage due to insufficient engine lubrication. Unlike many oil cooler kits, the FMOC11 keeps the factory oil to water cooler in position. This essentially doubles your engines oil cooling. We’ve also developed the kit to use a bespoke laser cut aluminium bracket which makes for perfect fitment to the i30N crash bar. Supplied with the kit are 2x pre-assembled, high quality double braided AN-8 oil lines. We’ve incorporated a thermostat that is built into the oil cooler sandwich plate, this has been set to open at 85C as this was observed to be the optimal working temperature of the oil cooler when testing, this means the engine is working at its most efficient oil temperature range however hard you push the vehicle.   The kit comes with the following: 1x Forge Aluminium sandwich plate1x Twin pass oil cooler 4x M6x20 fasteners4x M6 washers2x Oil lines 4x M6 Rubber Riv nuts1X M20x1.5 adaptorAll the fixings required    Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This kit has been designed to address the weakness of the stock oil cooler – the cooler fitted to your car from Audi is aluminium, but the fittings on the ends of the cooler hoses are steel. The result is corrosion between the two different metals which cracks the fittings over time, causing a slow oil leak that gets worse with age, and eventually ends in a catastrophic failure of the oil cooler lines - and if you are unlucky, the engine too. Due to the corrosion setting in on the lines, they usually cannot be removed from the oil cooler without damaging it. This results in the need for the oil cooler and both lines to be replaced at a cost of over £1100 from the dealer, before you factor in consumables and labour to change the parts. Our solution uses tried and test products. It is a full replacement right from the fitting on the engine block which is precision made from 6082 billet aluminium, and then anodised to prevent any possibility of corrosion. This fitting leads to -12 AN Hose Technik black anodised aluminium fittings on Hose Technik braided lines with black overbraid. Cooling is accomplished by a 19 row Setrab oil cooler, the same manufacturer that supplies Audi and several F1 teams, again with a black finish. All the mating parts are similar materials and are tried and tested in Motorsport - there is no fear of corrosion affecting the fittings after a few years of use. The cooler is supported on a laser cut and powder coated frame that also holds the Audi fan control module in place. With everything finished in black, it makes for the ultimate stealth installation and unless you know what you are looking for, you won’t see it. The original remit of this replacement was to do away with all the troublesome Audi parts, which this kit accomplishes, but by relocating the oil cooler slightly higher than stock, we have also reduced the chances of damage from road debris. All parts needed for installation are included - bolts, nuts, washers, brackets, and full instructions, though you will need up to additional 2 litres of engine oil to account for the loss from removing your old oil cooler, and for filling the new cooler and lines.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

TECHNICAL DATA AIRTEC Motorsport oil cooler kit for Astra H VXR.Designed and developed in house at AIRTEC HQ this makes our oil cooler kit unique and finished to a stunning level of quality.Grill mounted to achieve maximum cold airflow and fits either side of grill as not to affect cold air feed for air filters. Kit Includes. 13 row high performance AIRTEC motorsport oil cooler Aeroquip -8 90 & 45 degree Black anodised fittings with Black Pro-Lite Oil hose Gearbox mounted hose securing bracket finished in ProSeries Black Designed to fit with AIRTEC stage 3 intercooler & supplied with a bracket for cars running standard or other aftermarket intercooler!Today’s high performance vehicles pack a lot of power in a smaller package.In order to save both weight and space, the typical OEM cooling system is designed for “normal” driving conditions.When driven hard for extended periods, the cooling system may prove less than adequate.AIRTEC offers the solution to marginal cooling systems—race proven lightweight and efficient oil coolers designed to fit in the smallest practical space.

Read more less

TECHNICAL DATA The new AIRTEC oil cooler kit for R53 Supercharged Mini’s is a must mod for all modified cars Perfect for Fast Road and Track, keep those oil temps in check Features Earl’s temp ‘a’ cool oil cooler Powder coated Black AIRTEC logo securing bracket with fixings Satin Black High pressure oil lines Anodised Black Aero style fixing (made by Aerotec) Genuine Mocal thermostat Billet oil line separators Billet alloy oil adaptor plate ONLY AVAILABLE IN BLACK DOES NOT FIT WITH AIRTEC FRONT MOUNT INTERCOOLER KIT Airtec Part No: ATOILMINI1 

Read more less

AIRTEC Motorsport Universal Oil Cooler Our new range of AIRTEC Motorsport oil coolers are now available to order. These compact coolers are suitable for use with either engine or transmission oil and feature a high-flow 12-row core to aid cooling. They also features cast -8 or -10 male fittings (please select when ordering), to suit standard AN hose connections. The coolers also incorpoate universal cast mounting points, for easy fitment into any car, feature an AIRTEC embossed logo on the top side and come in a powdercoated satin black finish. Features: High-flow 12-row core Cast mounting points AIRTEC embossed logo Satin black finish Available to suit -8 or -10 AN fittings

Read more less

AIRTEC Motorsport Oil Cooler Kit for Hyundai i30N Following an extensive development process over the past year, AIRTEC Motorsport are proud to launch its new oil cooler kit aimed at modified i30N owners who struggle to maintain steady oil temperatures on track, or during fast road use. AIRTEC part no: ATMSHYU1 TECHNICAL DATA AIRTEC Motorsport Oil Cooler Kit for Hyundai i30N Following an extensive development process over the past year, AIRTEC Motorsport are proud to launch its new oil cooler kit aimed at modified i30N owners who struggle to maintain steady oil temperatures on track, or during fast road use. Our kit has been designed in the UK after thorough research and huge experience in developing uprated oil cooler packages for a variety of modified track and road cars. The challenge with this kit was to integrate a large capacity, external oil cooler mounted neatly behind the grille for direct airflow, whilst integrating seamlessly with the car’s existing fixtures and fittings with no drilling or cutting required. As a result, we have developed a kit that is completely reversable if need be. The comprehensive package includes a tried and tested 13-row AIRTEC oil cooler, bespoke laser-cut and powdercoated AIRTEC brackets, high quality braided hose lines with Aerotec fittings, and all fixtures, including instructions, for a simple bolt-on installation. Its cooling efficiency and easy fitment makes it an essential modification for all modified i30Ns. Key features: Designed and developed in the UK No cutting or drilling required to fit Reduces temperatures on track and road Proven AIRTEC large capacity external oil cooler Bespoke laser-cut and powdercoated brackets High-quality hoses and fittings Comprehensive kit with all fixtures, fittings and instructions Registered Design Right numbers: 6093141 & 6094142 AIRTEC part no: ATMSHYU1

Read more less

AIRTEC Motorsport are proud to offer the oil cooler kit for the Fiesta ST 180 Long overdue but it’s been worth the wait, making every part of our AIRTEC Motorsport oil cooler kit unique and finished to a stunning level of quality. Grill mounted to achieve maximum cold airflow and fits either side of grill as not to affect cold air feed for air filters. Kit Includes. 13 row high performance AIRTEC motorsport oil cooler Aerotec 90 degree Black anodised fittings with Black Oil hose Billet anodised hose line seperators x 4 Gearbox mounted hose securing bracket finished in ProSeries Black Designed to fit with AIRTEC stage 3 intercooler & suppled with a bracket for cars running standard or other aftermarket intercooler! Today’s high performance vehicles pack a lot of power in a smaller package. In order to save both weight and space, the typical OEM cooling system is designed for “normal” driving conditions. When driven hard for extended periods, the cooling system may prove less than adequate. AIRTEC offers the solution to marginal cooling systems—race proven lightweight and efficient oil coolers designed to fit in the smallest practical space. Registered Design Right number: 6030031 AIRTEC part no: ATOILFO4

Read more less