Oil Coolers

2.0 TSI DSGgearbox oil cooler ​ For DQ 250 6-speed and DQ381 7-speed It's not just your engine oil that you need to protect. Your DSG gearbox is very susceptible to overheating, leading to protection mode that reduces engine power and eventually prevents gear selection. Why fit theDSG oil cooler kit? Our unique DSG Oil Cooler Kit is an essential fit for any hard-driven MQB 2.0 TSI car running high power levels or in hot climates. It's a complete ready to install package, using a clever sandwich plate design for straightforward and completely reliable installation.   Transferring more power and torque through the DSG gearbox generates ever more heat to dissipate.  Significantly increased oil temperatures means only one thing: a decrease in the ability for your DSG box to stay properly cooled, eventually causing power drop and gear selection issues.  Under hard driving, the factory DSG oil/water cooler is easily overwhelmed. Problems start to occur when oil cannot dissipate its collected heat fast enough and the oil begins to thin and degrade - losing its lubrication properties. When this happens, the DSG will protect itself and begin to lower the engine torque, increase shift times and eventually loose gear selection. ooThe RacingLine kit solves this problem: by adding in an additional air/oil cooler positioned right in the airflow at the front of the car, oil temperatures are reduced by around 15  - 20   degrees centigrade (of course dependant on how the car is being used, ambient temps and state of tune). The kit uses a clever design which retains the factory oil/water cooling and adds to it with the thermostatically-controlled front-mounted cooler - doubling up your cooling capability when it's needed with less heat transfer into the water system. Only when the oil exceeds normal temperatures, the thermostat opens. Oil temperature then drops significantly as it is pumped through the densely packed fins of the 10-row cooler’s large surface area mounted right in the cool airflow. HIGH EFFICIENCY COOLER Our 10-row stacked plate design efficiently forces the hot oil through a series of aluminium pressed plates. Heat dissipates as cold air moves across the plates. 210 SERIES BRAIDED HOSE Our oil lines feature an attractive outer nylon braid strengthened by a stainless steel inner weave for maximum resilience. Protective external sheath avoids any rubbing damage in use.   TEMPERATURE CONTROL Our unique adaptor block oil take-off includes a clever internal thermostatic-control valve to direct oil flow through the cooler only when temperature hits 82°c/180°F. COLD AIR LOCATION The front-mount location brackets of the RacingLine cooler kit places it in the optimum airflow and ensures that oil temperature drops and excess heat is funnelled out efficiently. PRECISION MACHINED Precision machined billet components utilising the latest 5 Axis CNC machines for perfect accuracy, first time, every time.  LOW PROFILE COOLER The kit includes a replacement factory-spec oil/water cooler with a lower height, allowing for easy fitment without affecting the battery tray above it. CONFIRMED APPLICATIONS VWR29G7250 / DQ250 6-SPEED GEARBOXES ONLY * VWR29DQ381 / DQ381 7-SPEED GEARBOXES ONLY ​ *not for US-spec DQ250 with Secondary Air Intake (SAI) system > VW Golf 7 & 7.5 GTI & Clubsport 2013-2020 > VW Golf 7 & 7.5 R 2013-2020 > VW Golf 7 & 7.5 1.8 TSI 2013-2020 > VW Passat 2.0 TSI B8 2015+ > VW Arteon 2.0 TSI 2017+ > VW T-Roc R 2.0 TSI 2019+ > VW Tiguan II 2.0 TSI 2016+ > VW Jetta / GLI 7 2018+ > Audi S3 8V 2013-2020 > Audi A3 2.0 TSI / 1.8 TSI 8V 2013-2020 > Audi TT 3 8S 2014+ > Audi TTS 2.0 TFSI 8S 2015-2021 > Audi TT 2.0 TFSI 8S 2014+ > Audi TTS 2.0 TFSI 8S 320ps (EA888.4) 2021+ > Audi SQ2 2018+ > SEAT Leon III Cupra 5F 2014-2020 > SEAT Leon III 1.8 TSI 5F 2014-2020 > Cupra Ateca 2018+ > Skoda Octavia III vRS 2.0 TSI 5E 2014-2020 > Skoda Superb III 1.8 / 2.0 TSI 3V 2015+   DSG COOLER  FITMENT. As you’d expect, the RacingLine DSG Oil Cooler is a beautifully detailed complete kit, developed exclusively for MQB cars with either DQ250 6-speed or DQ381 7speed DSG gearbox.   The system is designed for straightforward fitting and ultimate reliability. Everything needed for perfect fitment is included.  Unlike other DSG oil cooler kits, the RacingLine package keeps the oil/water cooler and adds to it with the oil/air cooler 10 row stacked-plate oil cooler radiator, flowed to obtain maximum heat dissipation without undue pressure drop Optimum front mounted location behind left side front lower grill aperture with all necessary brackets and fixing kit supplied 210 Series stainless steel, nylon braided feed and return lines run past the chassis leg into the bumper cavity, then connecting to the oil cooler core DOUBLE COOLING. Our DSG Cooler design is a unique design: it retains the factory oil/water gearbox cooling system, plus adds our oil/air cooling as well. Why? The DSG oil will still quickly warm up from the hot water in the engine's coolant system, reaching full operating temperature as soon as possible. But that's where the problem begins on a hard-driven car. The hot engine coolant will now have little to no cooling effect on the DSG oil, and gearbox temps start to rise rapidly. That's the point at which our sophisticated thermostatic control valve inside the adaptor block will then divert hot oil out to the new 10-row cooler located in the cool fresh air flow. After the cooled transmission oil returns from the cooler, it carries less heat to be absorbed into the engine coolant system - helping control all the temperatures under the bonnet. Our replacement oil/water cooler (that's the silver part in the picture) is lower in height than the factory one. So the total height of both parts still fits perfectly under the battery location above it.  WHAT'S IN THE KIT?Oil cooler mounting brackets  AN10 210 series Nylon braided feed and return line Billet CNC thermostatic adaptor block Replacement, low-profile oil/water cooler AN10 10-row oil/air cooler core Fitting kit containing all necessary nuts, bolts, washers and rubber mounting bobbins BRACKET SETS The kit for all MQB cars comes supplied with two bracket kits. One kit is for Audi S3 models, the other is for all Golf 7 and other MQB models.  ​ Mounting for the bracket set requires drilling bolt holes through the front crash bar. GOLF 7 & 7.5 PLUS OTHER MQB MOUNTING AUDI S3 8V MOUNTING WHAT'S THE PROBLEM ON TRACK? When oil temperature reaches 138°C/280°F, the DSG's control system initiates a reduction in engine torque, meaning a serious drop in performance.   Carry on driving, and if temperatures then rise above 145°C/293°F, your DSG clutches no longer get the fluid pressure they require and you loose drive altogether as the box goes into a safety mode. ​ If you're in a hot climate this can happen after only about 15 minutes at the track - meaning a long wait while your gearbox cools down again. PRECISION ENGINEERED FOR PERFECT PERFORMANCE. Sophisticated thermostatic control adaptor block to divert oil flow around new cooling system - but only when needed Billet gloss-anodised for long-lasting protection and good looks Oil lines with protective outer nylon braid strengthened by a stainless steel inner weave for maximum resilience.  T6 6061 CNC aluminium used throughout for precision accurate fit 10-row stacked plate-design cooler efficiently forces the hot oil through a series of aluminium pressed plates.

Read more less

Developed from our direct involvement within the BTCC and Mini Challenge race series where we have provided race proven cooling packages, we have directly transferred our knowledge from this over to our road going products. FMOC11 has been developed with the same engineering expertise that is applied to our Mini Challenge Oil coolers, these see extensive driving over the race season calendar, so we are proud to give the I30N the same motorsport treatment. Lowering your oil temps on and off the track whilst providing a product that does not skimp on quality, so much so that it is backed by our Forge Lifetime Guarantee* With our extensive range of performance parts out on the market allowing the limits of the i30N/Veloster N to be pushed in the chase for top power gains, the addition of power and speed creates heat. Rising oil temperatures will result in only one outcome, a reduction of sufficient lubrication of your engines internal components. Therefore, the FMOC11 is a must have product for the keen driver, the location of the oil cooler radiator at the front of the vehicle’s radiator grill allows for superior air flow. During our development of this product we have seen oil temperatures reduced significantly. The Hyundai oil cooler has its inlet and outlets placed in the correct position for optimum flow , when oil coolers are fitted upside-down this can lead to cavitation (air locks) within the system, this can over a prolonged period of time lead to engine fatigue and potentially internal component damage due to insufficient engine lubrication. Unlike many oil cooler kits, the FMOC11 keeps the factory oil to water cooler in position. This essentially doubles your engines oil cooling. We’ve also developed the kit to use a bespoke laser cut aluminium bracket which makes for perfect fitment to the i30N crash bar. Supplied with the kit are 2x pre-assembled, high quality double braided AN-8 oil lines. We’ve incorporated a thermostat that is built into the oil cooler sandwich plate, this has been set to open at 85C as this was observed to be the optimal working temperature of the oil cooler when testing, this means the engine is working at its most efficient oil temperature range however hard you push the vehicle.   The kit comes with the following: 1x Forge Aluminium sandwich plate1x Twin pass oil cooler 4x M6x20 fasteners4x M6 washers2x Oil lines 4x M6 Rubber Riv nuts1X M20x1.5 adaptorAll the fixings required    Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less