Performance - Audi A4 B6 (2000-2006)

State of art polymer laminated glass cloth Superb heat barrier qualities Withstands radiant temperatures up to 450°C/850°F Ultra thin for minimal clearance As used in WRC and F1 Each roll is 50mm wide x 5 metres long (2" x 16ft) Adhesive backing for ease of fitting After extensive market research Forge Motorsport are proud to release a state of the art metalized polymer laminated glass cloth with adhesive backing that is both extremely light and capable of handling continuous radiant temperatures of up to 450°C. It reflects up to 80% of all radiant heat, whilst offering weight savings against other heat reflecting materials. Forge Motorsport's gold reflective heat barrier requires minimal clearance and is an extremely pliable material with a pressure sensitive adhesive backing that is easy to apply and remove. As used in WRC and F1, make no mistake this gold reflective heat barrier tape is of excellent quality and superb value for money. When used correctly this tape can be used to protect intake components thus lowering IATs resulting in a more efficient and reliable engine cycle. Typical uses are: Wrapping wiring, inside engine covers, bulkheads and firewalls, boost pipes, fuel lines, under seats, intake pipes, airboxes, engine compartments, fuel cells…  

Read more less

Product Description This is a replacement carbon canister including Pipercross filter that fits the FMINDGOLR twintake and Fiat FMINDF500 These have been created exclusively for Forge by filtration gurus Pipercross, and feature the latest multilayer-foam technology that is proving to be so successful in this season’s British Touring Car Championship  (BTCC). These are priced individually. Please order 2 when replacing carbon canister/filters on the FMINDGOLR system. *Please note - the Pipercross filter is excluded from the Forge lifetime warranty* The filter should be installed with a maximum clamp torque pressure of 3nm.Please watch our video on how to fit an air filter without damaging it.  

Read more less

Product Description 70mm I/D Rubber Neck Open Cone Air Filter - High flow construction and increased surface area Replaces the filter in the following kits - FMINDK5- Ford Fiesta 1.0 Ecoboost induction kit FMINDST180- Ford Fiesta ST180 induction kit FMINDASTG - Astra G induction kit *Please note - this filter is excluded from the Forge lifetime warranty* Please watch our video on how to fit an air filter without damaging it.

Read more less

This actuator is designed for the Audi A4 and Volkswagon Passat 1.8T engines that are longitudinally mounted. ( crankshaft of the engine runs inline or the length of the chassis) Forge Motorsport were one of the first company’s in the world to design and manufacture the billet two-piece replacement aluminium turbo actuator. Originally for the Cosworth, Renault 5 GT turbo, and Lancia Integral turbos, we soon developed the largest and most diverse range of actuator replacements. Choice of spring pressures to suit your car Manufactured from 6026 grade aluminium Vehicle specific Turbo specific Built to order Machined and hand polished in the UK Choice of piston or diaphragm operation on most actuators Nomex reinforced flurosilicone diaphragms Laser cut stainless steel brackets (where applicable) Tuning and service kits available Made in England Lifetime warranty* Please Note: The pressure figures listed in the drop-down menu above are minimum regulated pressure figures. If you are unsure, please don't hesitate to call us on 01452 380999.  When you fit a Forge turbo actuator you will be able to fine tune and manage your specific boost requirements, this will allow for improved response and better control. This product is built with a predetermined actuator spring suitable for, or slightly above factory boost levels. The actuator can be assembled with a stronger spring upon request for tuned vehicles, and where a higher boost level is required. Please contact us directly concerning this process. It is designed and built with the intention of increasing the boost output of a turbocharged system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket Diaphragm sealed internals are the default selection for this actuator product but customers now have the option of piston sealed internals. Unique to Forge Motorsport, this innovation offers equal performance to the diaphragm type and low maintenance due to the hard wearing nature of piston sealed valve internals. Forge Motorsport nor any of its authorised distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment. While Forge Motorsport is happy to supply you with an actuator capable of holding boost beyond that of your factory unit we are in no way capable of knowing nor suggesting that your vehicle's engine or related systems are capable of supporting or surviving the stresses of such elevated boost pressure. In The Box:1 x FMACVAG02 Actuator1 x Forge Sticker This actuator is built with a green coded spring as standard. If you require the FMPACTUN spring tuning kit seen in the associated products below, you will need to select the Diaphragm Type 2, 049 option.   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This pipe allows the removal of the Exhaust Gas Recirculation valve on the 1999-2005 VAG (transverse) 1.9 PD diesel engine with the following codes: ALH (90bhp), ATD (100bhp), AHF (110bhp), ASV (110bhp), AJM (115bhp) and AUY (115bhp). Incorporated onto the replacement pipe is a secured blanking plate and a boost gauge connection, which can be blanked off if not needed with a short length of pipe (supplied). Please note: All parts necessary for installation are included, however it is necesary to re-use the existing valve "O" ring seal with this pipe. FITS: AudiA3DieselA4DieselSeatAlteaIbizaMk2 (6K2) 1999-2002DieselMk3 (6L) 2002-2008DieselLeonMk2 2005-2012DieselSkodaFabia6Y 1999-2007VRSOctaviaDieselVolkswagenGolfMK4DieselMK5Diesel   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

This turbo recirculation valve is the result of of 25 years of experience and engineering expertise. With the reputation for innovating and manufacturing the best automotive valves in the world, you can be certain that there is currently no better replacement valve available. The FMDV008PA version seen here has the benefit of a 90 degree vacuum port, that can be rotated to three different orientations. This is often the preference where either space is restricted, or the original fitment valve has a 90 degree connection, either on the valve or connecting hose. Forge's recirculation valve features a greater flow rate than the OEM Bosch Valve, as well as a faster response time, due to our revised design. By using the associated service kit (FMDVSK), as seen below, the life of the valve can be extended, and the performance can be maintained. With a lifetime guarantee, you can be sure the valve is reliable for your car.  It is fully customisable to fit your application with two uprated springs provided in the kit. Forge Motorsport's improvement on the original valve has a compact design, meaning easy fitment under the engine cover. Please select whether you want a black or matt silver valve, using the options above. In The Box:1 x FMDV008PA Valve1 x Uprated Yellow Spring1 x Uprated Blue Spring1 x Cable Tie1 x 2.5mm Allen key2 x 35mm Hose Clamps1 x Instruction Booklet1 x Forge Sticker FITS: AudiA31.8TA41.8T (B5,B6 Models)A61.8T (B5,B6 Models)Allroad 2.7Bi-TurboS31.8T (8L Chassis)TTMk1NissanMicraIG-T 90 TeknaPorscheCayman 718 SGTS 2.5 TurboRenaultClioMk40.9 TCE 2012-SeatLeonMk1 1998-2005Cupra 1.8TCupra R 1.8TSkodaOctavia1.8TVolkswagenBeetle1.8TBora (1998-2005)GolfMK41.8TPassat1.8TPolo1.8T *Porsche 991/911 Turbo will require 2 Valves - please see our seperate product (FMDV008P2 below)* The valve has a port size of 25mm If you are unsure if this product is suitable for your application, please contact us.    Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Vehicles

Read more less

The Splitter is a truly remarkable valve that gives a combination of blow off and recirculation valve operation, all at the same time, and has been specifically designed for the many turbo engined applications that operate metered airflow management systems. This means you get all the noise of the blow off valve whilst retaining the compatibility with the recirculation requirements of the engine management system. As a bonus we also offer the ability to convert the valve to recirculation only mode for those times when stealth running is required. This valve uses a Brass piston which utilises new sealing technology along with a variable spring preload, incorporating a ratchet type top adjuster that will allow for the positive and precise adjustment to match the valve to your engine. This is achieved by using a unique single, conical, progressive rate spring, that can allow for the retention of boost pressure over a wide adjustment range. This unique spring design also allows for unrestricted piston travel and flow volume regardless of the amount of pre-load adjustment added to the spring. Other manufacturers' valves use cylindrical springs with adjustable pre-load, which often experience restricted piston travel and a reduction in flow volume. When we say our products are Engineered For Performance, it's not a catchy sales phrase, it's the truth. and we prove it with every product we manufacture. Note: This valve requires installing the opposite way to the original Bosch Valve. This means that the side pipe is fitted into the Turbo Intake Hose, and the base pipe connects to the hose that runs to the boost side of the turbo.   In The Box:1 x FMDVSPLTR Valve1 x Valve Blanking Cap1 x Instruction Booklet1 x Forge Sticker If you are unsure if this product is suitable for your application, please contact us.  The valve has a port size of 25mm fits: AudiA31.8TA41.8T (B5,B6 Models)A61.8T (B5,B6 Models)S31.8T (8L Chassis)TTMk1150/180BHP210/225BHPSeatIbizaMk2 (6K2) 1999-2002PetrolMk3 (6L) 2002-2008PetrolLeonMk1 1998-2005Cupra 1.8TCupra R 1.8TSkodaOctavia1.8TVolkswagenBeetle1.8TBora (1998-2005)GolfMK41.8TPassat1.8TPolo1.8T         To service this valve, access the valve piston by removing the 3 cap screws at the base of the valve and simply clean the piston chamber using brake cleaner or similar cleaning fluid before installing the new spring and piston. Please observe the correct spring and piston orientation when installing the serviceable parts, as seen in the attached drawing.   Adjustment guide. First turn the valve adjustment knob all the way down in the anti-clockwise direction, which will adjust the spring it to its lowest tension. Then turn the valve adjustment knob in the clockwise direction to the appropriate tension level, as set out below. Standard engine – 16 clicks. Stage 1 remap – 21 clicks. Stage 2 remap – 25 clicks. These adjustment recommendations are a general guide and you may find that your engine requires fine tuning by 1 or 2 clicks in either direction to achieve optimum performance. There will be no significant performance benefit adjusting the valve over 30 clicks as the spring will have reached its maximum operating tension.     Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   Fits Multiple Vehicles

Read more less

Before fitment, please ensure the spacer fits flat to the back of the wheel. These wheel spacers are hubcentric These CNC machined precision alloy wheel spacers are 13 mm thick with a dual 5 stud bolt pattern for both 100 and 112mm PCD fitments. The spacers are anodised black to inhibit corrosion and "bonding" to the wheel or hub. These spacers are suitable for most vehicles produced by Volkswagen Group. A 13mm spacer will give an overall track increase of 26mm when fitted to both sides of an axle. These spacers are priced and sold per pair. Extended wheel bolts are not supplied.   In The Box:2 x FMWS13 13mm Wheel Spacer1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Now you can fine tune your Blow Off/Diverter Valve to the exact needs of your engine with this complete tuning kit. If you are finding that the valve is dumping more than required, or if you are losing boost pressure it is normally an indication that a stronger spring is required. Alternatively, if the valve is failing to dump it may be necessary to install a weaker spring. Please note that fitting a stronger spring into a valve will not increase boost pressure, unless existing pressure is being lost. Failure to allow the valve to operate by installing a spring which is too strong, may cause damage to the turbocharger. Please also note that the red coded springs should not be installed in the DVR or DV007 diaphragm valves.  Valve Spring color coding: Green - 5-15 PSI, Yellow - 15-23 PSI, Blue - 23-30 PSI, Red - 30 + PSI.*The above figures are estimates only and should only be considered as a guideline* Note: Serious or fatal damage may occur to the engine and associated components if this product is incorrectly matched to the individual engine requirements. Forge Motorsport nor any of it’s authorised distributors can assume any responsibility for any adverse effects resulting from the installation of this product.  Please contact us if you are uncertain whether this kit is suitable for your valve. *Please Note - The colours of the springs illustrated may differ to what you receive. All spring kits are brand new but are not sprayed. Colour is used as an identifier*   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   FOR MULTIPLE VEHICLES 

Read more less

The Forge UNOS boost controller is a ball and spring CNC machined to aircraft grade specifications and incorporates a ratchet type top adjuster that will allow for the positive and precise adjustment that your driving style demands. The controller can be dash or engine bay mounted to suit your preference. This product is a universal component, and as such, no vehicle-specific fitting instructions can be provided. This product is designed and built with the intent of increasing the boost output of any forced induction system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket. Forge Motorsport nor any of it’s Authorized Distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment.   In The Box:1 x FMUNOS Boost Controller1 x Uprated Unos Spring2 x Unos Brackets2 x M4 x 8 Socket Cap Bolts1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Please note: spacers are sold as PAIRS! if you want to do front and rear than qty x2 is needed!These CNC machined precision alloy wheel spacers are 8 mm thick with a dual 5 stud bolt pattern for both 100 and 112mm PCD fitments. The spacers are anodised black to inhibit corrosion and "bonding" to the wheel or hub. These spacers are suitable for most vehicles produced by Volkswagen Group. A 8mm spacer will give an overall track increase of 16mm when fitted to both sides of an axle. These spacers are priced and sold per pair. Extended wheel bolts are not suppliedPlease note, Due to the nature and complexity of a wheel spacer, customers MUST know that the size they are ordering is correct prior to ordering by measuring your stud length and wheel groove depth. Unfortunately, if over tightened the integrity of the spacer and / or bolts can be compromised - and due to this, any spacer that has been fitted, trial fitted or removed from its packaging can not be returned! Please be aware of this as by ordering you agree to this!

Read more less