Performance - Mercedes G Class (W460 / W461) 1979-1992

State of art polymer laminated glass cloth Superb heat barrier qualities Withstands radiant temperatures up to 450°C/850°F Ultra thin for minimal clearance As used in WRC and F1 Each roll is 50mm wide x 5 metres long (2" x 16ft) Adhesive backing for ease of fitting After extensive market research Forge Motorsport are proud to release a state of the art metalized polymer laminated glass cloth with adhesive backing that is both extremely light and capable of handling continuous radiant temperatures of up to 450°C. It reflects up to 80% of all radiant heat, whilst offering weight savings against other heat reflecting materials. Forge Motorsport's gold reflective heat barrier requires minimal clearance and is an extremely pliable material with a pressure sensitive adhesive backing that is easy to apply and remove. As used in WRC and F1, make no mistake this gold reflective heat barrier tape is of excellent quality and superb value for money. When used correctly this tape can be used to protect intake components thus lowering IATs resulting in a more efficient and reliable engine cycle. Typical uses are: Wrapping wiring, inside engine covers, bulkheads and firewalls, boost pipes, fuel lines, under seats, intake pipes, airboxes, engine compartments, fuel cells…  

Read more less

Product Description This is a replacement carbon canister including Pipercross filter that fits the FMINDGOLR twintake and Fiat FMINDF500 These have been created exclusively for Forge by filtration gurus Pipercross, and feature the latest multilayer-foam technology that is proving to be so successful in this season’s British Touring Car Championship  (BTCC). These are priced individually. Please order 2 when replacing carbon canister/filters on the FMINDGOLR system. *Please note - the Pipercross filter is excluded from the Forge lifetime warranty* The filter should be installed with a maximum clamp torque pressure of 3nm.Please watch our video on how to fit an air filter without damaging it.  

Read more less

Product Description 70mm I/D Rubber Neck Open Cone Air Filter - High flow construction and increased surface area Replaces the filter in the following kits - FMINDK5- Ford Fiesta 1.0 Ecoboost induction kit FMINDST180- Ford Fiesta ST180 induction kit FMINDASTG - Astra G induction kit *Please note - this filter is excluded from the Forge lifetime warranty* Please watch our video on how to fit an air filter without damaging it.

Read more less

Now you can fine tune your Blow Off/Diverter Valve to the exact needs of your engine with this complete tuning kit. If you are finding that the valve is dumping more than required, or if you are losing boost pressure it is normally an indication that a stronger spring is required. Alternatively, if the valve is failing to dump it may be necessary to install a weaker spring. Please note that fitting a stronger spring into a valve will not increase boost pressure, unless existing pressure is being lost. Failure to allow the valve to operate by installing a spring which is too strong, may cause damage to the turbocharger. Please also note that the red coded springs should not be installed in the DVR or DV007 diaphragm valves.  Valve Spring color coding: Green - 5-15 PSI, Yellow - 15-23 PSI, Blue - 23-30 PSI, Red - 30 + PSI.*The above figures are estimates only and should only be considered as a guideline* Note: Serious or fatal damage may occur to the engine and associated components if this product is incorrectly matched to the individual engine requirements. Forge Motorsport nor any of it’s authorised distributors can assume any responsibility for any adverse effects resulting from the installation of this product.  Please contact us if you are uncertain whether this kit is suitable for your valve. *Please Note - The colours of the springs illustrated may differ to what you receive. All spring kits are brand new but are not sprayed. Colour is used as an identifier*   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.   FOR MULTIPLE VEHICLES 

Read more less

The Forge UNOS boost controller is a ball and spring CNC machined to aircraft grade specifications and incorporates a ratchet type top adjuster that will allow for the positive and precise adjustment that your driving style demands. The controller can be dash or engine bay mounted to suit your preference. This product is a universal component, and as such, no vehicle-specific fitting instructions can be provided. This product is designed and built with the intent of increasing the boost output of any forced induction system. We cannot guarantee compatibility with all applications, nor the ability to increase the boost output beyond a level that is within the parameters set by the engine-management-system of the given vehicle at the time of installation, whether that system is factory or aftermarket. Forge Motorsport nor any of it’s Authorized Distributors can assume any responsibility for any adverse effects resulting from the installation and tuning of this product onto a vehicle whose engine-management-system, whether factory or aftermarket, is not capable of allowing for the desired level of adjustment.   In The Box:1 x FMUNOS Boost Controller1 x Uprated Unos Spring2 x Unos Brackets2 x M4 x 8 Socket Cap Bolts1 x Forge Sticker   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less