Revo Hardware

TURBO INLET HOSE The Revo Turbo Inlet Hose has been designed and engineered to directly replace the stock pipe and elbow found in vehicles with the 1.8 and 2.0 TSI engines with an IHI turbo. The Revo Turbo Inlet Hose offers a high-quality single piece replacement for the OEM parts which allows for smoother uninterrupted airflow, improving the throttle response and performance of your vehicle. KEY FEATURES Increased performance Improves airflow efficiency Constant taper for smoother flow Turbo matched inlets Replaces restrictive stock turbo elbow Engineered for both LHD and RHD fitment OEM PART With ample efficiency for a stock vehicle, the OEM system quickly becomes a choking point for the engine when running Revo Software. With a generously sized airbox, the standard plastic intake hose causes the most amount of restriction; convolutions designed to allow for engine movement disrupt airflow, a small internal diameter limits the volume of air and a sharp reduction in hose diameter at the turbo causes turbulence.   TURBO INLET The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The machined billet aluminium inlet securely fits the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence.   SILICONE HOSE DESIGN The Revo Turbo Hose as an increased inner diameter that gradually tapers from airbox to turbo to optimise airflow, while maintaining the tolerances required to fit both LHD and RHD vehicles with a standard airbox. Designed to directly replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range.   A four-ply construction with an internal wire helix increases strength to prevent collapsing under pressure. Internal steps flush fit against the stock airbox and the machined inlet, creating a smooth transition between components ensuring the smoothest airflow possible to the turbo. A machined bung is integrated into the hose, connecting the stock PCV system vacuum.       RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested. The Revo Turbo Inlet Hose allows the Stock IS38 turbo to run more efficiently, intake a larger volume of air and minimise turbulence. This increases power and torque, especially at the top end of the rev range as highlighted during controlled Dyno testing.   GRAPHS DATA Up to 12WHP and 15NM gains Graphs produced with Revo stage 2 software on Audi S3 8V Stock Runs with complete OEM Air intake setup Revo Runs with Revo Intake Hose and ProPanel Filter   VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V) 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Volkswagen Golf (MK7) R 2.0 TSI 12 - Volkswagen Golf (MK7) GTI 2.0 TSI 12 - Volkswagen Golf (MK7) 1.8 TSI 12 - Volkswagen Passat 2.0 TSI 15 -  

Read more less

VW GOLF MK6 GTI HIGH FLOW AIR FILTER INTAKE SYSTEM Our full air filter intake kit offers the following:  Replaces the complete standard airbox and includes heat-shield to the conical filter Includes full fitting kit and instructions for simple fitting Increases engine note – releasing the real noise of your engine Longer lifespan before cleaning required, compared to original or cotton filters Easy cleaning, no dirt caught like with V shaped filter grooves Bench tested for improved fuel economy, power and torque outputs The triple layer foam design The low maintenance and long lifespan aspects of a Revo filter come from the special triple layer foam that is used on all of our air filters. The outer core is coarse foam designed to trap larger particles, the middle core is Medium foam designed to trap most particles and the inner core is fine foam which will trap the remainder of the particles. The triple layer foam design ensures an exceptional level of engine protection in any conditions.   VEHICLE APPLICATIONS      Manufacturer Model Engine Year Audi A3 (8P) 2.0 TSI 2003 - 2012 Seat Leon MK2 2.0 TSI 2005 - 2012 Skoda Octavia Mk2 1.8 / 2.0 TSI 2005 - 2013 VW Golf MK6 2.0 TSI 2008 - 2013 VW Beetle 2.0 TSI 1999 > VW Scirocco 2.0 TSI 2008 > VW Tiguan 2.0 TSI 2007 > Notes: Simple replacement of the OEM part Please contact your local Revo Authorised Dealer for additional information and availability.

Read more less

EVERYTHING YOU NEEDFOR THE POWER YOU CRAVE PLEASE NOTE: SOFTWARE HAS TO BE INSTALLED BY DEALER! Enhanced power delivery, unique safety features and exhilarating response at your disposal, the Revo Performance Pack delivers much more than peak power figures. Whatever drives you, the Revo Performance Pack has it all. Engineered to perform, only Revo offers a complete tuning solution specifically designed for your vehicle. AIR INTAKE SYSTEM PERFORMANCESOFTWARE INTERCOOLER PIPE UPGRADE KIT INTERCOOLER     OPEN CONEAIR INTAKE SYSTEM Revo Open Cone Systems completely replace the OEM air intake for those who like to announce their vehicle is far from standard. Along with an aggressive intake sound, more air means access to more power throughout the rev-range. IncreasedDiameter DirectFlow PerformanceDesigned Learn more about this product PERFORMANCE ECU SOFTWARE Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev range while maintaining the extensive factory safety mechanisms. Revo Software offers a perfect balance of performance, economy, longevity, and safety so you can drive harder, for longer. OBDII PortInstalled Vehicle HealthCheck Authorised DealerSet-up Read More     INTERCOOLER PIPE UPGRADE The Revo Intercooler Pipe Upgrade kit comes as part of the Revo Intercooler. It reduces charge system resistance and improves flow over the restrictive stock pipework. Featuring fewer restrictions for smoother airflow, and optimised routing, the turbo meets less resistance and can perform more effectively. DirectReplacement IncreasedDiameter DirectInternals Learn more about this product INTERCOOLER UPGRADE The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Unique design features lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software, ensuring you get consistent performance when you need it most. DirectReplacement UniqueFin Design MinimisedPressure Drop Learn more about this product     STOCK POWER200PS TORQUE290NM POWER262PS TORQUE395NM Find your nearest Revo Authorised Dealer Manufacturer Model Variant Engine Year Ford Fiesta Mk8 ST 1.5 EcoBoost 2017 > Images shown are for illustration purposes only All Revo Software availability is ECU ID Dependant. Upgrade pricing for existing Revo Stage 1 ECU customers.  Terms and Conditions apply.  Performance data is taken from 2018 Fiesta ST Mk8. Additional SPS Software Switch purchase required for some software features.  Pricing does not include the installation of parts, please contact your local Revo Authorised Dealer

Read more less

REVO AIR INTERCOOLER 1.8/2.0 TFSI The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow thus decreasing turbulence and increasing airspeed into the bespoke bar and plate core. These features enhance charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures even compared to the Audi S3 (8P) cast aluminium intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment 51% Increased Core Volume over a standard cooler 21% Increased Core Volume over an OE S3 cooler Lower Intake Temperatures INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has a much larger core volume than the OEM part and offers perfect fitment, improving cooling by utilising the full volume of the stock location space as well as cold ambient air from the front of the vehicle. END TANK DESIGN End tanks play an important part in managing pressure drop and work in harmony with the core to promote airflow, the stock ones are inefficiently designed and create turbulent air in corners. These sections create a naturally small cross-sectional flow area, slowing charge air and increasing pressure drop. The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core by removing these turbulent pocket areas found in the OE design. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions from turbulent air pockets found in the OE intercooler. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR AND PLATE CORE Designed with a bar and plate core to maximise the efficiency of heat transfer and minimise flow resistance, the Revo Intercooler easily outperforms similar tube and fin alternatives in both aspects. The Revo Intercooler goes a step farther: featuring carefully specified fin sizing and geometry to further optimise the balance between air cooling and flow restriction. The ambient core side utilises shorter fins with specially designed louvres to slow ambient air passing through the core, which improves heat transfer. While the charge core side features an offset internal fin design to balance surface area and air resistance to aid cooling ability and minimise pressure drop.   SILICONE HOSES Supplied with stronger oil resistant silicone hoses, the Revo Intercooler can be installed using the stock pipework or recommended Revo Intercooler pipework (Coming soon). The internal diameter of each silicone is precisely matched to the inner diameter of the ribbed intercooler inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components.   BRACKETS To ensures precision fitment, Only Revo offers a CNC machined bracket system. Produced to a superior tolerance than that of a cast mounting system, this unique feature also ensures that the supporting brackets are strong and less prone to failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout of the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OE S3 (8P) intercooler with a Revo K04 Kit, Revo production KO4 software, a Revo air intake system and full Eurojet exhaust, the Revo Intercooler was then installed and tested in the same controlled environment to highlight the benefits of it's enhanced cooling. PERFORMANCE DATA Golf GTI TSI EA888 Gen1 with Revo K04 upgrade, OE S3 (8P) intercooler and Revo open cone air intake system and full Eurojet exhaust. Showing the last of five consecutive dyno runs, the efficiency of the Revo Intercooler over the OE S3 intercooler is highlighted. With max gains of +8 HP & +11NM Torque, along with increased performance throughout the entire rev range, the stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, losing no peak power over the 5 runs. INLET TEMPERATURE This is a metric used to confirm that testing on the Revo Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were equal between both coolers, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency advantage. OUTLET TEMPERETURE This graph illustrates the increased cooling performance of the Revo intercooler vs OEM S3 (8P) aluminium intercooler over all five runs. The Revo Intercooler keeps temperatures well below the OE S3 intercooler throughout all 5 runs.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi A3 (8P) 1.8 / 2.0TFSI 2004-2013 Audi S3 (8P) 2.0 TFSI 2006-2012 Seat Altea 1.8 / 2.0 TFSI/TSI 2004-2010 Seat Leon (MK2) 1.8 / 2.0 TFSI/TSI 2004 - 2012 Seat Toledo 1.8 / 2.0 TFSI 2004 - 2009 Skoda Octavia (MK2) 1.8 / 2.0 TFSI/TSI 2004 - 2013 Skoda Superb (B6) 1.8 / 2.0 TSI 2008 - 2013 Skoda Yeti* 1.8 / 2.0 TSI 2010 - 2013 VW EOS 2.0TSI 2006 - 2016 VW Golf (Mk5/6) 1.8 / 2.0 TFSI/TSI 2004 - 2014 VW Jetta (Mk5) 1.8 / 2.0 TFSI 2006 - 2010 VW Scirocco 2.0 TFSI/TSI 2009 - 2014 VW Tiguan* 2.0TFSI 2007-2010 * Yeti / Tiguan fitment for FWD vehciles only. Does not fit AWD.  DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo TFSI Intercooler Instructions NOTES Simple replacement of the OEM part Also available for the MQB Platform

Read more less

The factory 2.0 TFSI air-box works efficiently on a standard vehicle. As power is increased through tuning, however, it quickly becomes a major restriction, reducing the additional power offered. Ensuring the engine can get access to enough air is paramount when increasing power, an open cone air-intake system is the most effective way of achieving this, but not all products are made equal. Having worked with a number of intake solutions during software development, we noticed a lack of high quality and more importantly, high flowing kits available. Working alongside some of the biggest names in the air filter industry, we engineered and designed what is still one of the highest flowing kits available. Pioneering design allows air to reach the turbo as quickly as possible whilst minimising turbulence and restriction. As a result, boost can be maintained for longer, giving you access to more power throughout the rev-range along with a more aggressive sound, and performance you can feel all the way to the redline. BENEFITS Increases power and torque Maintains boost for longer Single piece pipe 25% less restriction Three-layer foam filter Scaled MAF housing CamCoat option available INTAKE PIPE The Revo engineering team knew that to create the most effective kit, every component had to be considered to maximise and smooth airspeed. The system is designed around a lightweight 90mm intake pipe, mandrel bent to maintain the internal diameter in the corners and to create a one-piece solution. This offers superior flow and avoids the air turbulence and resistance experienced on intake kits with multiple sections, usually caused at each join resulting in very turbulent airflow, ultimately restricting performance. MAF SCALING Ensuring correct MAF (Mass Air Flow) sensor scaling is the real art when it comes to designing air intake systems if incorrect the intake system can actually reduce power and cause major fuelling issues. The Revo kit integrates the stock MAF sensor in a specifically designed housing on the one-piece pipe to ensure correct scaling during fitment. THREE LAYER FOAM FILTER An intake system is only as good as the filter. This kit comes complete with a tried and tested Revo three-layer foam filter with an impressive 857cm² surface area, supported by galvanised, epoxy-coated mesh to ensure the filter cannot collapse. The filter has a large 180mm external diameter body and a smooth radius aluminium bell mouth, specifically designed for optimum airflow from the filter to pipe-work. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze, which are surface filters designed to trap particles on the outer layer, instantly causing restriction. Revo foam filters work by trapping dirt particles within each of the oiled foam layers, allowing air to negotiate its way through the filter, reducing restriction and offering much longer service intervals. We tested the filter at a leading motor testing centre ‘Mira’ on an industry recognised dust load test. On a full dust load test, the foam filter was found to still be 99.1% efficient, filtering down to 5 microns while offering the least amount of restriction over similar products. HEAT SHIELD The intake system features a laser-cut aluminium heat shield that ensures the filter is well insulated from ambient under-bonnet temperatures. The shielding is designed to utilise the ducting in the factory grill to maximise airflow and prevent heat-soak. SILICONE HOSE The silicone hoses included in the kit are manufactured using high-quality automotive grade silicone, engineered to combine the system using stepped necks to offer a smooth transition of air to avoid turbulence. The turbo inlet hose has also been specifically designed to fit both K03 and K04 turbo powered cars. TESTING 2.0 TFSI Intake Restriction  2.0 TFSI Stock vs Stage 1 Power Graph 2.0 TFSI Stock vs Stage 1 Power Graph   INTAKE PERFORMANCE FIGURES Engine Software Power Torque 2.0 TFSI (K03) Stage 1 + 16 BHP + 5 NM 2.0 TFSI (K04) Stage 2+ + 40 BHP + 15 NM   *Maximum power and torque increases are shown in testing when using Revo 2.0 TFSI intake system compared to a stock intake   TECHNICAL DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the RT992M200700 Revo 2.0 TFSI Air Intake System Fitting Instructions     FITMENT      Manufacturer Model Engine Year Audi A3 (8P) 2.0 TFSI 2006 - 2012 Audi S3 (8P) 2.0 TFSI 2006 - 2012 Seat Leon MK2 2.0 TFSI 2005 - 2012 Seat Altea 2.0 TFSI 2006 - 2009 Skoda Octavia Mk2 2.0 TFSI 2005 - 2013 VW Golf MK5 2.0 TFSI 2003 - 2009 VW Golf MK6 (R, ED35) 2.0 TFSI 2008 - 2013 VW Scirocco R 2.0 TFSI 2008 > VW Jetta 2.0 TFSI 2006 - 2010 VW Passat 2.0 TFSI 2005 - 2010

Read more less

REVO INTERCOOLER PIPE UPGRADE The Revo Intercooler Pipe Upgrade kit reduces charge system resistance and improves flow over the restrictive stock pipework. Designed for the Audi B9 chassis with the longitudinal 2.0TFSi engine, this upgrade features larger internal diameters, fewer restrictions for smoother airflow, and optimised routing. Reinforced, oil resistant silicone hoses, lightweight mandrel-bent aluminium pipework and flush fit joins to eliminate turbulence, the Revo Intercooler Pipe upgrade is designed to fit either the stock or Revo Intercooler. A multitude of design features and attention to detail that only Revo offer means this a product that performs. KEY FEATURES Increased internal diameter Smoother airflow Fits Revo and stock intercooler +8HP & 9NM Water Meth Bung KIT CONTENTS Revo throttle pipe Revo charge hose Revo throttle pipe Silicones Hose clamps INCREASED VOLUME Each part of the kit has been designed to increase the overall diameter and increase internal volume. Larger charge air volume in the system means reduced flow resistance, allowing the turbo to expend more energy on air compression and less energy overcoming restrictions; resulting in more power. CHARGE HOSE DESIGN The Revo charge hose is a smooth custom-designed silicone hose, with a tapered first bend from the turbo outlet to gradually transition to a larger diameter. The charge pipe is designed to directly replace the OEM part utilising optimised pipe routing and a unique constant-diameter design. Wire helix reinforcement with 5mm wall thickness gives greater strength and rigidity while allowing enough clearance from engine parts, increasing performance without compromising fitment. THROTTLE PIPE DESIGN The Revo throttle pipe is much larger than the stock part, manufactured using mandrel-bent aluminium hard pipe volume has been increased by 23%. The reinforced oil resistant silicone hoses are stepped and ID-matched to promote laminar, uniformed flow across the transition of parts. This part also has an integrated water methanol bung placed near the throttle body, allowing easy access from the top of the engine bay.     RESEARCH AND DEVELOPMENT  All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The benefits of the Revo intercooler pipe upgrade allows the turbo to run more efficiently, moving a larger volume of air and minimising turbulence. This increases power and torque, especially in the middle of the rev range as highlighted during controlled dyno testing. PERFORMANCE  Back to back testing of both the OEM intercooler pipe work and Revo upgrade was carried out on an Audi A4 B9 (2.0 TSI EA888 Gen 3) fitted with Revo intercooler, Stage 2 Software and the stock air intake system. The overall power gains between the two sets of runs was 8HP and 9NM. DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo Audi B9 2.0 TFSI Intercooler Pipe Upgrade Instructions

Read more less

REVO OEM+ INTAKE SYSTEM Get impressive performance benefits without compromising on the factory look of your engine bay. Revo OEM+ Air Intake Systems utilise the existing airbox, replacing any restrictive components with parts precisely engineered to reduce turbulence and improve airflow. The B9 Audi A4 shares the same airbox as the higher powered S4 and RS4 models and performed well during initial testing of volume and flow. This air intake system upgrade includes a Revo foam filter and a flush-fit silicone hose to minimise air restriction and turbulence, improving airflow and giving you access to more power. KEY FEATURES Increased Airflow by up to 20% Three-layer foam filter Stepped Silicone Hose +11Hp and 13NM performance gains KIT CONTENTS Revo ProPanel Filter Revo Silicone Hose Revo Takeoff Stainless Steel Clamps AIRFILTER The standard paper filter found in most vehicles performs well under normal conditions, however, with the increased power it becomes a major choking point in the system. Revo filters work by trapping dirt particles within each of the oiled foam layers while allowing air to negotiate its way through, reducing restriction and offering much longer service intervals. The new Revo filter features an OEM top plate, allowing a direct fit replacement for the stock airbox. SILICONE HOSE The plastic hose on the stock system is designed with a corrugated style to flex with the engine movement, while this has its place it also causes a large amount of turbulence as the airflow doesn’t have a smooth direct path to the turbo. We designed the silicone hose with stepped internals to ensure a flush fit, and to minimise turbulence while still allowing for engine movement. SELF-SEAL TAKEOFF The OE B9 A4/A5 intake hose has a small vacuum take-off used to supply vacuum to various components of the engine. To replicate this, the Revo B9 A4/A5 intake hose utilizes a threaded self-seal barb. This machined configuration offers a better aesthetic and more durability than typical plastic and glued couplers.   PERFORMANCE  Testing was carried out with consistent conditions on both the OEM intake and the Revo OEM+ Intake System on a 2017 Audi A4 B9 2.0 TFSI Quattro (252ps) running Revo Performance ECU Software and hardware. While dyno testing for performance gains, VCDS software was used to log airflow with a full AEM logging suit used to monitor temperatures. The Revo Intake increased vehicle performance, especially higher in the rev range, highlighting the performance benefits over the stock components.   AIRFLOW Testing of the stock unit back to back against the Revo OEM+ kit on a full flow bench was carried out to highlight the largest restrictions in the system. The Revo OEM+ Intake system had far less restriction than the OE unit, at 480CFM the stock unit was seeing 619mmwg restriction while the Revo unit only saw 530mmwg some 14% less restrictive. At low flow rate the Revo intake provided up to 20% less restriction, improving throttle response. The graph below shows the flow test and comparison between the OE and Revo intakes.   FITMENT   Manufacturer Model Engine Variant Year Audi A4 2.0TFSI B9 252PS 2015> Audi A5 2.0TFSI B9 252PS 2015> Audi Q5 2.0TFSI B9 252PS 2015> *Note: Plastic airbox lid not included in the kit.   DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo Audi B9 2.0 TFSI Intake Instructions  

Read more less

REVO CONE CONE AIR INTAKE SYSTEM AUDI S1 2.0 TFSI The Revo open cone Air Intake System for the Audi S1 improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock airbox, pipework and filter on the Audi S1. The Revo System offers a high-quality open cone replacement complete with a heat shield to improve airflow and the performance of your vehicle. KEY FEATURES Increased performance +13HP at hubs & +18NM Torque Improves Air Flow Efficiency 53% Larger Hose & Inlet Volume Three Stage Foam Filter with Mesh Silicone Coolant Hose OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and silicone hose which joins directly to the turbo inlet. Revo Flush Fit joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at all tuning stages. SILICONE HOSE The Revo silicone hose is designed to directly replace the plastic hose and rubber corrugated parts. Increased inlet diameter of 21% reduces restriction and promotes smooth airflow while an integrated wire helix reinforces the hose and prevents collapsing under negative pressure.   MACHINED INLET The machined inlet replaces the restrictive OEM plastic elbow and is designed to securely fit the OE unit using locking tabs and integrated O-rings. Only the Revo intake kit features an inlet almost double the cross-sectional area. This means air can stabilise and distribute before a smooth tapered transition to the turbo.   FILTER AND HEATSHIELD Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points and rubber mounting bushings to provide an easy and secure installation.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled Dyno testing. AIRFLOW  An overall air volume increase of 50% over the OE part allows for faster and increased airflow. The carefully designed silicone hose has its own support bracket mated to a machined hose fitting, maintaining the correct position during engine movement. A constant taper in the hose ensures a smooth transition of airflow from the air filter to turbo and results in an increase in air volume over the stock part. Further helped by the machined inlet that matches the turbo inlet for the ultimate in airflow characteristics.   DYNO GRAPH Testing was carried out on an Audi S1 2.0 TFSI (6 Speed manual) with Revo Stage 1 Software fitted with the OEM system and then the Revo Air Intake System. With a consistent gain throughout the rev range, the Revo intake offered a peak gain of 12HP at the hubs over the stock part. A maximum increase in airflow of up to +16 kg/hr gives impressive gains of 13HP @5100rpm and 18NM @5100RPM over using the stock intake system.   FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi S1 2.0 2014>  

Read more less

The Audi RS6 and RS7 are without doubt quick in their purest form, add Revo Stage 1 and 2 software however, they quickly become supercar killers. Giving the cars an even further boost in their already staggering power figures, we turned our attention to developing an upgrade for the air intake system. Testing found that the RS air-box had a tremendous amount of potential, with only a few key areas that caused restriction.The new direct replacement kit includes a Revo foam filter, stepped silicone hoses and an aluminium tag. We installed the kit on an RS7 development vehicle, on our Dynopak hub dyno we saw improved power and torque throughout the rev-range, with consistent gains of +4WHP and +4NM over the stock filter and hoses when used with Revo Stage 1 ECU performance software.  BENEFITS Increased airflow +4 WHP and + 4 NM gain Retains factory airbox Custom designed Silicone Hoses Revo ProPanel filter AIR FILTER The standard paper filter found in most vehicles performs well under normal conditions, however, with increased power it becomes a major choking point in the system. Revo ProPanel filters work by trapping dirt particles within each of the oiled foam layers while allowing air to negotiate its way through, reducing restriction and offering much longer service intervals. We tested the filter at a leading motor testing centre ‘Mira’ on an industry recognised dust load test. On a full dust load test, the foam filter was found to still be 99.3% efficient, filtering down to 5 microns while offering the least amount of restriction over similar products. SILICONE HOSES The plastic hoses on the stock system design with a corrugated style to flex with the engine movement, while this has its place it also causes a large amount of turbulence as the airflow doesn’t have a smooth direct path to the turbos. We designed the silicone hoses with stepped internals to ensure a flush fit and to minimise turbulence while still allowing for engine movement.     INTAKE PERFORMANCE FIGURES Engine Software Power Torque 4.0 TFSI Stage 1 + 4 BHP + 4 NM   *Maximum power and torque increases are shown in testing when using Revo 4.0 TFSI intake system compared to the stock intake on Audi RS7   TECHNICAL DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the  RA731M200200 Revo 4.0 TFSI Air Intake System Fitting Instructions     FITTING      Manufacturer Model Engine Year Audi RS6 4.0 TFSI 2012 > Audi RS7 4.0 TFSI 2012 >

Read more less

The Audi S6 and S7 are impressive cars straight out of the box, yet when combined with Revo’s market leading software they come into a world of their own. In our search to extract more power from the mighty 4.0 TFSI engine, we quickly found that the stock air-box and filter became a major limitation for the car. During research and development, our in-house engineers worked with both the S7 and RS7 to analyse and compare the differences in each intake system, and how efficiently they performed. The direct replacement kit, which includes an RS7 air-box, Revo ProPanel filter and stepped silicone hoses was installed and tested on our in-house S7 development vehicle; the results were staggering. On our Dynopak hub dyno we saw dramatically improved power and torque throughout the rev-range, with consistent gains of +21WHP and +24NM with our Stage 2 software installed. BENEFITS Increases power and torque +21 WHP and + 24 NM gain OEM+ Look Custom designed Silicone hoses Revo ProPanel filter AIRBOX The S and RS air-box may look very similar at a glance, however after analysis and testing of both air-boxes, it was quite clear that the RS air-box had a tremendous amount of potential with a few essential improvements. The two inlet pipes have a larger 100mm diameter, allowing more air to flow with much less restriction compared to the 85mm stock air-box inlets. Revo software really allows the car to utilise this increase in airflow, all without compromising on the OEM look of the engine bay. SILICONE HOSES To compensate for the larger outlets on the RS7 air-box, we designed and developed two larger silicone hoses to join the air intake system to the engine. Revo’s flush fit designed silicone hoses connect to the air-box without any internal restriction, minimising turbulence and allowing a smoother flow of air to maximise performance. REVO PROPANEL FILTER The standard paper filter found in most vehicles performs well under normal conditions, however with increased power it becomes a major choking point in the system. Revo ProPanel filters work by trapping dirt particles within each of the oiled foam layers while allowing air to negotiate its way through, reducing restriction and offering much longer service intervals. We tested the filter at a leading motor testing centre ‘Mira’ on an industry recognised dust load test. On a full dust load test the foam filter was found to still be 99.3% efficient, filtering down to 5 micron while offering the least amount of restriction over similar products. FULL KIT The Revo 4.0 TFSi intake kit comes complete with RS7 air-box, Revo ProPanel filter, silicone hoses and fitting brackets. The kit offers an OEM+ look and fit, with no required modifications to the vehicle, finished off with an aluminium tag.   TESTING Revo 4.0 TFSI intake kit vs Stock     INTAKE PERFORMANCE FIGURES Engine Software Power Torque 4.0 TFSI Stage 2 + 21 BHP + 24 NM   *Maximum power and torque increases shown in testing when using Revo 4.0 TFSI intake system compared to stock intake on Audi S7   TECHNICAL DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the  Revo 4.0 TFSI Air Intake System Fitting Instructions     FITTING      Manufacturer Model Engine Year Audi S6 4.0 TFSI 2012 > Audi S7 4.0 TFSI 2012 >

Read more less

Revo Air Intake System Seat Ibiza Cupra The Revo open cone Air Intake System for the Seat Ibiza Cupra improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock airbox, pipe work and filter on the Seat Ibiza Cupra. The Revo System offers a high-quality open cone replacement complete with a heat shield to improve airflow and the performance of your vehicle. Key Features Increased performance +25HP at hubs & +30NM Torque Improves Air Flow Efficiency 53% Larger Hose & Inlet Volume Three Stage Foam Filter with Mesh OEM vs Revo When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and silicone hose which joins directly to the turbo inlet. Revo Flush Fit joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at all tuning stages. Silicone Hose The Revo silicone hose is designed to directly replace the plastic hose and rubber corrugated parts. An increased inlet diameter of 21% reduces restriction and promotes smooth airflow while an integrated wire helix reinforces the hose and prevents collapsing under negative pressure.   Machined Inlet The machined inlet replaces the restrictive OEM plastic elbow and is designed to securely fit to the OE unit using locking tabs and integrated O-rings. Only the Revo intake kit features an inlet almost double the cross-sectional area. This means air can stabilise and distribute before a smooth tapered transition to the turbo.   Filter and Heatshield Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points and rubber mounting bushings to provide an easy and secure installation.   Research and Development All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled Dyno testing. Airflow An overall air volume increase of 50% over the OE part allows for faster and increased airflow. The carefully designed silicone hose has its own support bracket mated to a machined hose fitting, maintaining the correct position during engine movement. A constant taper in the hose ensures a smooth transition of airflow from the air filter to turbo and results in an increase in air volume over stock. Further helped by the machined inlet that matches to the turbo inlet for the ultimate in airflow characteristics.   Dyno Graph Testing was carried out on a VW Polo GTI 1.8 TSI (6 Speed manual) with Revo Stage 1 Software fitted with the OEM system and then the Revo Air Intake System. With a consistent gain throughout the rev range, the Revo intake offered a peak gain of 20HP at the hubs and 20NM torque over the stock part. A maximum increase in airflow of upto +16 kg/hr gives impressive gains of 27HP @6100rpm and 30NM @4600RPM over using the stock intake system.   Fitment Vehicle Applications Manufacturer Model Engine Year Seat Ibiza Cupra 1.8 GTI 2016>   Please note: this product will not fit LHD vehicles. Documents The following documents are available to view: Fitting instructions Download the Revo Seat Ibiza Cupra Intake Instructions Notes Simple replacement of the OEM part

Read more less

Revo 1.8 TSI OEM+ System Increased Power, Torque & Throttle Response Overview The new 1.8 TSI intake has been designed to work in harmony with our Revo software. Starting by looking at the OE system we set about deciding where we could improve on the current design, it was apparent from the outset that the factory airbox was more than substantial for the flow of air the car required. The stock airbox is actually about 15% larger than the airbox on the MK7 Golf Gti. So we decided to keep with the airbox on this basis and had one of the Revo  ProPanel filters designed to replace the restrictive OE paper element to allow the turbo to breathe easier. The next section of the factory intake was the OE intake hose which feeds the clean air from the airbox into the turbo. The stock hose is made out of plastic with multiple ridges in it to allow for flex of the intake system under load, however having these ridges causes a lot or turbulence to the air. We re-designed the hose to eradicate this, maintaining the precise OE fit whilst eradicating any turbulence issues. Working alongside SamcoSport ensured the highest quality product, we opted to use high temperature nomex fabric to withstand the heat from the turbo, and automotive grade silicone rubber to avoid fading or perishing over time. The inner ridges made way for smooth inner walls which after testing increased both airflow and speed resulting in more power and flow. To avoid the all too common problem of hose collapse under negative pressure from the turbo, we incorporated an embedded wire helix to prevent this from happening, no matter how much more power you run.   Benefits OEM+ Look New silicone Samco hose to mimic OE whilst eliminating turbulence Increased airflow and speed resualting in better power Optimum performance working in harmony with Revo Software Consistent gains and reduction in restriction + 8WHP Power and + 8NM Torque gains (Audi S1) Kit INCLUDES Revo ProPanel Filter Revo by Samco Intake hose 2 x Hose Clamps (Air box not included)   More Air, Less Restriction Testing was carried out in various ways, dyno, flow and road. On the flow testing we set up the stock system on a flow test bed, The ISO5011 performance test, measures the restriction (measured in mm WG) created by the air filter and any equipment used in the air intake at multiple air flow rates (measured in CFM). The test uses a flow bench to draw air through the air intake at a given flow rate. The flow rate is calculated by measuring the pressure difference using a manometer across a set orifice. A second manometer is used to measure the depression or vacuum created by the air intake. The lower the vacuum created by the air intake the better it has performed in the test. Each component of the system was measured, analysed and improved to enable us to maximise the performance of the intake. The results were great and the complete Revo intake system compared to the full stock OE system showed a 19% reduction in restriction at 400CFM.     Revo S1 Intake Torque Graph Revo S1 intake Power Graph Air Flow Chart   *Dyno testing was carried out on our Dynopak 4 wheel drive dyno and on back to back dyno runs we saw consistent gains between 5-8 WHP and 8NM Torque (Audi S1 Test)      Technical Documents The following documents are available to view: Fitting Instructions Download the RA831M600100 Revo Audi 1.8 TSI OEM+ Intake Fitting Instructions Fitment      Manufacturer Model Engine Year Seat Ibiza Cupra 1.8 TSI 2015 > VW Polo GTi 1.8 TSI 2015 >

Read more less

Revo ProPanel FilterHigh-Performance Air Filters OVERVIEW The Revo ProPanel is a high-grade direct replacement filter for your vehicle. Designed as direct replacement filters to fit inside your factory air box and are suitable for road or competition use.   BENEFITS Designed to increase horsepower and rate of acceleration Exceptional filtration High airflow with three layers of foam Lifetime warranty Lasts up to 60,000 miles before cleaning is required depending on driving conditions Works with original manufacturers air box   DESIGN AND PERFORMANCE Why choose foam? Because, compared to paper or other filter technologies, reticulated polyester foam achieves optimum performance against three key criteria: Maximum airflow: the ability to allow air to pass through without causing a large drop in pressure. Cleaning efficiency: the capability to arrest a high proportion of airborne dust while feeding the engine clean air. Dust load-up tolerance: the capability to absorb a large amount of dust without reducing airflow capacity. This design of filter has been used in all fields of motorsport from Formula 1 to the World Rally Championship. The range receives this same attention to detail at the design stage and is then taken into production with consummate quality.   THREE LAYER FOAM SYSTEM Revo ProPanel Filters use multi-layered foam technology to trap dust and dirt while maintaining flow efficiency over time. Using foam increases the filter's surface area and is washable, compared to standard paper and cotton filters which trap dust on the surface and become less efficient the more they are used, choking the engine and reducing performance. The outer core is a coarse foam designed to trap larger particles, the second layer is a medium foam designed to trap most particles and the inner core is fine foam which will trap any particles small enough to reach it. The triple layer foam design ensures an exceptional level of engine protection and long-term performance advantage.     1: Stainless steel wire mesh To avoid erosion, only the highest quality steel is used.   2: Course outer layer:  Stops large pieces of dirt and foreign matter from penetrating further. Straightens airflow into subsequent layers.   3: Medium grade middle layer:  This second filtration layer traps most of the harmful dirt that leads to engine damage.   4: Fine inner layer:  Extracts fine particles while allowing full air flow to the engine for maximum power.     ADVANTAGES OF A REVO PROPANEL FILTER Emissions legal in all 50 US states Will not void vehicle warranty Lifetime warranty (to original purchaser with proof of purchase)     FITTING      Manufacturer Model Engine Year Audi RS3  2.5 TFSI  2015 > Audi TTRS  2.5 TFSI  2016 > VW Arteon  2.0 TDI  2017 > VW Passat  2.0 TDI  2014 >  

Read more less

FORM FOLLOWS FUNCTION The Revo Carbon Series Air Intake system is a direct replacement kit and includes a beautiful carbon lid designed to increase the flow of air by utilising the enlarged diameter outlet and increased volume. The Revo Panel Filter upgrade replaces the restrictive stock paper filter, and a Revo carbon intake pipe allows air to flow smoothly to the turbo from the airbox, resolving the restrictions found during flow testing of the OEM system to improve your engines response and the power it can create. KEY FEATURES Increases air volume Enlarged airbox outlet Smooths air flow and reduces restriction Direct replacement carbon fibre kit Proven performance benefits KIT CONTENTS Carbon airbox lid Carbon intake pipe Silicone airbox hose Silicone reducer Propanel Filter CARBON AIRBOX LID Manufactured using the highest quality materials, the Revo carbon airbox lid directly replaces the standard plastic part with an increased outlet size of over 13% being fed by specially designed airflow channels. A gloss carbon finish coupled with impressive performance benefits delivers in form and function, looking great in the engine bay yet still performing above and beyond the OEM part. CARBON INTAKE PIPE The newly designed carbon fibre pipe smoothly tapers from the airbox to the turbo, removing the corrugated plastic section of stock pipe and provides the smoothest possible airflow. The 20% size increase and thermal properties of the carbon keep intake temps lower, allowing the 2.5 TFSI engine with Revo ECU performance software to produce more power. PROPANEL FILTER Revo Panel Filters use multi-layered foam technology to trap dust and dirt while maintaining flow efficiency over time. Using foam increases the filter's surface area and is washable, compared to standard paper and cotton filters which trap dust on the surface and become less efficient the more they are used, choking the engine and reducing performance. AIRBOX SILICONE HOSE No detail has been overlooked when reducing restrictions within the stock airflow system. The stock corrugated plastic hose is replaced with a smooth silicone one, reducing air turbulence. A three-ply construction with the addition of fluorine for added protection, increases strength to prevent collapsing under pressure. Internal steps flush fit against the stock air box and the turbo inlet, creating a smooth transition between components ensuring the smoothest airflow. SILICONE REDUCER To ensure smooth airflow from the carbon intake to the turbo inlet, a tapered 4 ply silicone hose has been designed with includes a full fluoroline inner to protect against oil vapour. The silicone has perfectly matched internal steps to reduce any unwanted turbulence through the transition of parts, the steps are match to the outer diameter of the carbon pipe, and the internal diameter of the turbo inlet.   PERFORMANCE Testing was carried out with consistent conditions on both the OEM intake and the Revo Carbon Series Air Intake System on a 2018 Audi TTRS running Revo Performance ECU Software. While dyno testing for performance gains, VCDS software was used to log airflow with a full AEM logging suit used to monitor temperatures. The Revo Carbon Series Intake increased vehicle performance, especially over 3600rpm with 16whp and 31NM gains, highlighting the performance benefits over the stock components.   AIRFLOW The only way to fully test the maximum airflow and restriction was to test both the stock and Revo intake on a controlled Flow test bed. The testing was carried out using a 76mm orifice plate to simulate the size of the stock turbo inlet. The Carbon Series Revo system had far less restriction than the OE unit, at 480CFM the stock unit was seeing 452mmwg restriction while the Revo unit only saw 371mmwg some 21% less restrictive, even at 540CFM the Revo intake only saw 467mmwg restriction and still had more headroom. The graph below shows the flow test and comparison between the OE and Revo intakes.   FITTING   Manufacturer Model Variant Year Audi TTRS 8J 2017> Audi RS3 8V 2018>   DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo Carbon Series TTRS Intake Instructions

Read more less

REVO INTERCOOLER AUDI TTRS 8S 2.5TFSI The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 55ºC vs. the 8S TTRS intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment with Integrated Crash bar Intercooler Pipes Included Up to 80% Increased Core Volume Over 55ºC Lower AIT   INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has an 80% larger core volume than the OEM part and offers perfect fitment. By integrating a reinforced OE crash bar, it allows access to a volume of unused engine bay space to be filled with the intercooler core. END TANKS DESIGN The stock cast end tanks on the 2.5TFSI cooler do provide elevated performance benefits over the typical plastic end tank coolers. However, the Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. The width of the cooler makes for an extremely large volume end tanks, yielding impressive airflow. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR & PLATE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient airflow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   INTEGRATED CRASH BAR To increase the core size and volume the Revo intercooler has integrated an OEM crash bar, requiring extra provisions within the design to ensure correct fitment and crash bar rigidity. The welded connection has been reinforced with plates to transfer any force away from these areas and adding additional safety factors to the assembly. This also allows the dynamic weight of the intercooler to be distributed through the bar, rather than solely relying on the locating brackets at the bottom of the cooler.   INTERCOOLER PIPE UPGRADED Supplied with an upgraded aluminium mandrel-bent throttle pipe and a 6ply silicone charge pipe. The increased diameter pipework ensures the maximum performance by increasing system volume by over 27%. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components. The throttle hard pipe also includes a water-methanol injection port. RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo Stage 2 software (BETA), a Revo Carbon series air intake system and Milltek downpipe, the Revo Intercooler and pipes were then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA Showing the last of six consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM TTRS intercooler is highlighted. With peak gains of +40 HP & +41NM Torque, along with increased performance throughout the entire rev range. The stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, INLET TEMPERATURE This is a metric used to confirm that testing on the Revo TTRS 2.5TFSI Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were hotter on the Revo Intercooler, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERATURE This is the main performance metric to illustrate that the Revo intercooler far exceeds the stock unit, in fact, one of the most effective Revo intercoolers to date. The graph illustrates the increased cooling performance of the Revo intercooler vs OEM TTRS intercooler over all six runs. The Revo Intercooler provided a massive 57.4°C max and 17.5°C average intake air temperature reduction across the six back to back full gear dyno runs.   INTERCOOLER PRESSURE DROP GRAPH Pressure drop is an important factor when it comes to choosing an Intercooler. The Revo solution features custom cast end tanks to evenly distribute air over the core. This graph highlights that even with massive core size difference there is only a 0.23psi pressure drop in comparison to the stock intercooler, ensuring engine response and minimised turbo lag. You can rest assured that your vehicle will drive and respond as you would expect standard; until you press that pedal!     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi TTRS 2.5 TFSI 2017 onwards DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo TTRS Intercooler Instructions NOTES Simple replacement of the OEM part

Read more less

OEM+ INTAKE The Revo open cone Air Intake System for the Ford Ranger improves performance and removes restrictions found in the OEM system. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo Software. Engineered to directly replace the stock plastic intake pipe and filter. This kit comes complete with a silicone hose, air filter and fitting kit. KEY FEATURES Increased Performance Improved Air Flow Efficiency Three Stage Foam Filter with Mesh Stepped Silicone Hose OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. OEM+ systems utilise the stock airbox but remove other restrictive parts to enhance airflow to the turbo. Revo Flush Fit silicone hoses mean joins eliminate unwanted turbulence and increase the rate at which air can flow, ensuring maximum performance at any level of tuning. SILICONE HOSE The Revo intake hose is designed to directly replace the plastic corrugated parts. The 4ply silicone intake hose reduces turbulence and internal restrictions. The smooth internal bore results in no loss of cross-sectional area and allows increased airspeed through the intake. FILTER An intake system is only as good as the filter. This kit comes complete with a custom Revo foam filter, supported by galvanised epoxy-coated mesh for strength under load. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze alternatives designed to trap particles on the outer layer. Revo filters trap debris and particles within the foam layers, allowing air to still navigate through. The filter is also reusable. ADDITIONAL FEATURES The Revo hose also keeps the OE PCV take-off location and is supplied with a CNC machined 6061 adaptor which offers greater durability than the stock plastic take-off. The hose clamps supplied with this kit are made of stainless steel. This means they not only have high tensile strength but also will not corrode over time causing a failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase airflow, as highlighted during controlled testing.   LOWERING TEMPERATURES To show the efficiency of the Revo Intake, airflow was measured using our own Ford data logging software. Logging a 3rd and 4th gear pull through the rev range you see the improvements of the Revo Intake compared to stock. The Revo intake manages to hold consistent airflow through the gear change and gives a maximum airflow gain of 16% with an average of 5% throughout the runs.     FITTING      Manufacturer Model Engine Year Ford Ranger 2.2 TDCI 2015 - Ford Ranger 3.2 TDCI 2015 -

Read more less

REVO ENGINE MOUNTS FORD FIESTA MK8 REAR TORQUE MOUNT OEM engine mounts are designed with very low NVH (Noise, Vibration and Harshness) in mind. While this offers the smooth ride that most drivers desire, it becomes a very limiting factor for those who prefer performance and response. The Revo rear torque mount is designed to eliminate excessive movement, allowing you to reach your true performance potential and get the power down when you need it. Manufactured from only the best materials, our design team worked closely with industry leaders Powerflex to ensure a product that will perform when you need it most. Polyurethane bushes can perform under the most extreme of conditions, ensuring strength and stability under tremendous pressures. Tuned specifically for energy transfer they offer smoother shifts and limited wheel hop, providing you with a better driving experience and increasing the opportunity to use the power your car has to offer. KEY FEATURES Dramatically reduce engine movement Smoother gear changes CAD designed for precise fitment Custom designed Powerflex bushings Full CNC machined body and locating pins   HOUSING Precision CNC machined from aircraft-grade 6061 T6 aluminium, the main housing is extremely strong yet lightweight and offers a solid base to perfectly house each polyurethane bush. Finished with an engraved Revo logo and red Powerflex bushes PINS Both pins have been specially machined to safely house the bolts to ensure precise fitment and stop any damage to the polyurethane bushings. The large bush pin is CNC machined from a single billet piece of aluminium and reduces the risk of failure from running multiple parts. The small pin is made from stainless steel to offer greater strength and increase product life.   POLYURETHANE BUSHES BY POWERFLEX Powerflex utilises a unique formula of polyurethane, custom-designed to ensure optimum fitment in the machined housings. Polyurethane is also resistant to oil, fuel unlike the rubber used in the OEM mount which can lead to perishing and failure. Using two different custom durometer bushings gives the ultimate balance of performance and comfort.   LARGE BUSHING WASHER Designed to sit the opposite side of the large pin and made from 3mm stainless steel, we have added this washer to reduce the lateral movement of the mount. By limiting the lateral movement it reduces excessive force placed on the bushes and allows for a more secure fixing of the mount between the OE plates.   FITMENT DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo Ford Fiesta Rear Engine Mount Instructions NOTES Simple replacement of the OEM part Failures have been reported with the stock mounts V2 Design. A washer has been added to limit lateral movement.   VEHICLE APPLICATIONS Manufacturer Model Engine Year Ford Fiesta MK8 1.5 ST 2017 - 2022 PRE FACELIFT ONLY * For vehicles with manual gearboxes only Please note: due to the nature of Torque Mounts, the bushes can be compromised by incorrect fitment etc. Due to this there is a zero tolerance return policy on all torque mounts, By purchasing you agree to this.This includes items that are claimed to be unused!

Read more less

REVO RF0 WHEELLIGHTWEIGHT. STRONG. FLOW FORMED.  OVERVIEW The RF0 wheel is a flow-formed alloy that's lightweight yet exceptionally strong, designed in-house at Revo HQ in the UK. Flow forming is one of the most advanced manufacturing technologies to enter the wheel industry. Flow Forming Technology involves the application of pressure to the inner barrel of the wheel while spinning and after it has been cast. This process stretches and compresses the aluminium, which increases tensile strength. In this respect, the process shares similar properties to those found in the forging process. The final product is lighter, stronger, has increased elongation, and much greater shock resistance as well as an increased load capacity over regular cast wheels. Whilst the RF0 wheel shares a similar design concept to our previous generation RV0, the more advanced manufacturing process offered through flow forming allows for more definition in the design, particularly noticeable in the spokes and rim edge fillets. By reducing the weight of your wheels 'unsprung weight' your suspension starts to have a much easier time. Each bump can be controlled more quickly and easily. This helps keep your tyre in contact with the road for longer, which is obviously great news for car control and braking. Reducing the 'rotational mass has its benefits too. A classic/timeless motorsport look featuring an embossed Revo logo and branded centre cap to compliment the subtle styling. Available in a choice of Gloss Black, Matte Bronze & Matte Anthracite. BENEFITS TÜV approved Flow formed manufactured Lightweight at only 8.85kg Fits Revo big brake kit* COLOUR OPTIONS Gloss Black Matte Bronze Matte Anthracite   FITTING      Manufacturer Model Variant Year Ford Fiesta MK8 EcoBoost 2017 Onwards Ford Fiesta MK8 ST 2018 Onwards Ford Focus Mk1 RS 2002-2003 Ford Focus Mk1 ST170 2002-2004   REVO BIG BRAKE KIT The RF0 range of wheels are lightweight and strong and give the car great look while still fitting with the Revo Big Brake Kit. The RF018 4x108 ET40 18" wheel will fit directly over the Revo 332mm Disc with 4pot monobloc calliper. NOTES Fitment table above is a guide, please check your vehicle for correct fitment. When using the RF019/018 wheels on track it is advised that you remove the centre caps from the wheel to avoid distortion due to excessive heat transfer Price includes x4 RF018 wheels, Tyres not included. © Revo

Read more less

OPEN CONE INTAKE The Revo open cone Air Intake System for the 2.0T Gen3 engine improves performance and offers an aggressive intake sound. Ensuring your engine can get access to enough air is paramount when increasing power; more air means more power throughout the rev-range. Only Revo Air Intake Systems are specifically designed to work in harmony with your vehicle and Revo ECU Software. Engineered to directly replace the stock airbox, pipework and filter, this kit comes complete with a silicone hose, aluminium pipe, heat shield, filter, machined turbo coupler and fitting kit. KEY FEATURES Increased Performance (+12BHP +23Nm) Improved Air Flow Efficiency Three Stage Foam Filter with Mesh Direct to turbo fitment OEM VS REVO When you begin to enhance performance, the restrictive OEM intake struggles to flow enough air, robbing the engine of power. The Revo Air Intake System removes these restrictive elements promoting smoother airflow. Open Cone systems replace the OEM air box to make space for the heat shield, filter and silicone hose which joins directly to the turbo. Revo Flush Fit silicone hoses avoid unwanted turbulence at joins, and increase the rate at which air can flow ensuring maximum performance at any level of tuning. SILICONE HOSE The Revo silicone hose as an increased inner diameter that gradually tapers from hard pipe to turbo to optimise airflow. Designed to directly replace the plastic hose and turbo elbow, this upgrade reduces restriction and maximises smooth airflow improving both power and torque throughout the rev range. A machined billet bung is integrated into the hose, connecting the stock PCV system vacuum. TURBO INLET The Revo machined inlet replaces the restrictive elbow found on the IS20/IS38 turbos. The billet aluminium inlet securely fits the OE unit using locking tabs and integrated O-rings. With almost double the cross-sectional area compared to other available products, air can stabilise and distribute before a smooth tapered transition to the turbo. Removing the internal steps between components further ensures uninterrupted airflow and removes any unnecessary turbulence. HEATSHIELD Ensuring the engine has access to cold air is vital for performance. The Revo heat shield channels cold air from the front intake duct while partitioning the filter from the heat of the engine bay. The Revo Heatshield uses the stock mounting points to provide easy and secure installation. FILTER An intake system is only as good as the filter. This kit comes complete with a custom Revo foam filter, supported by galvanised epoxy-coated mesh for strength under load. Revo three-stage foam filters work very differently to conventional paper or cotton-gauze alternatives designed to trap particles on the outer layer. Revo filters trap debris and particles within the foam layers, allowing air to still navigate through.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house and are rigorously tested utilising an in-house 3D printer, latest CAD and CFD programs, hub dyno and Revo data acquisition software. The Revo intake allows the turbo to run more efficiently, intake a larger volume of air and minimise turbulence to increase both power and torque, as highlighted during controlled dyno testing.   PERFORMANCE DATA Back-to-back testing of the stock air intake system and the Revo kit were carried out. Fitted to an Audi S3 (310PS Model) with Revo ECU Software, Revo Intercooler, Revo Charge & Throttle Pipes and Revo Downpipe. The results show improvement throughout the whole rev range. The Revo intake offering an average gain of +12WHP, and +18NM torque over the stock part. Increased airflow also delivers impressive peak performance gains of +19.4BHP @6000rpm and +55NM @2400RPM over the stock intake system. AIRFLOW To evaluate the efficiency, the Revo Intake was tested for inlet charge pressure and mass airflow. Boost pressure was measured and an increase in charge pressure was seen across the top end of the RPM range, as detailed in the dyno graph. Intake mass airflow logging showed similar results to the charge pressure, showing considerable increases at the top of the RPM range.     FITTING      Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V)/td> 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Seat Ibiza Cupra 1.8 TSI 15 - Volkswagen Golf (MK7) 2.0 TSI GTI 14 - Volkswagen Golf (MK7) 2.0 TSI R 14 - Volkswagen Golf (MK7) 1.8 TSI 12 -

Read more less

EVERYTHING YOU NEEDFOR THE POWER YOU CRAVE Enhanced power delivery, unique safety features and exhilarating response at your disposal, the Revo Performance Pack delivers much more than peak power figures. Whatever drives you, the Revo Performance Pack has it all. Engineered to perform, only Revo offers a complete tuning solution specifically designed for your vehicle. AIR INTAKE SYSTEM PERFORMANCESOFTWARE INTERCOOLER PIPE UPGRADE KIT INTERCOOLER     CARBON SERIESAIR INTAKE SYSTEM Beautifully crafted from the highest quality 3k carbon, the Revo Carbon Series is much more than a visual enhancement. Designed to directly replace restrictive OEM components, the Carbon Series has performance woven into the core of every product. IncreasedDiameter DirectInternals ThermalBarrier Learn more about this product OPEN CONEAIR INTAKE SYSTEM Revo Open Cone Air Intake Systems completely replace the OEM air intake for those who like to announce their vehicle is far from standard. Along with an aggressive intake sound, more air means access to more power throughout the rev-range. IncreasedFlow DirectReplacement IncreasedDiameter Learn more about this product     PERFORMANCE ECU SOFTWARE Revo performance Software is designed to safely enhance the driveability of your vehicle, giving access to more power and torque throughout the rev range while maintaining the extensive factory safety mechanisms. Revo Software offers a perfect balance of performance, economy, longevity, and safety so you can drive harder, for longer. OBDII PortInstalled Vehicle HealthCheck Authorised DealerSet-up Read More TCU SOFTWARE Revo Transmission Control Unit Software allows your automatic gearbox to work in harmony with Revo ECU Software. As well as enhanced driveability and quick shifts, Revo TCU Software is packed full of features. OptimisedShift Points DynamicLaunch Control GlobalDevelopment Programme Read More     INTERCOOLER PIPE UPGRADE KIT The Revo Intercooler Pipe Upgrade kit reduces charge system resistance and improves flow over the restrictive stock pipework. Featuring fewer restrictions for smoother airflow, and optimised routing, the turbo meets less resistance and can perform more effectively. DirectReplacement IncreasedDiameter DirectInternals Learn more about this product INTERCOOLER UPGRADE The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Unique design features lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software, ensuring you get consistent performance when you need it most. DirectReplacement UniqueFin Design MinimisedPressure Drop Learn more about this product     STOCK POWER300PS TORQUE380NM 0 - 60 MPH4.6S 100 - 200 KPH14.2S POWER400PS TORQUE550NM 0 - 60 MPH3.6S 100 - 200 KPH8.8S Find your nearest Revo Authorised Dealer Manufacturer Model Variant Engine Year Audi S3 8V 2.0 TFSI 2014 - 2019 Audi TTS 8S 2.0 TFSI 2014 > SEAT Leon Cupra 5F 2.0 TSI 2014 - 2019 Skoda Superb 3V 2.0 TSI 2014 - 2019 VW Arteon 3H 2.0 TSI 2017 > VW Golf R Mk7 2.0 TSI 2014 - 2019 VW Golf GTI Clubsort Mk7 2.0 TSI 2016 - 2018 VW Golf GTI Clubsort S Mk7 2.0 TSI 2016 - 2017 Images shown are for illustration purposes only All software and features are ECU/TCU ID dependant. Upgrade pricing is for existing Revo ECU or/and TCU customers.  Terms and Conditions apply.  Exhaust Overrun is an seperate file option that can be choosen at point of software installation. Performance data is taken from 2016 VW Golf R Mk7 with DSG. Aftermarket downpipe required. Pricing does not include the installation of parts, please contact your local Revo Authorised Dealer.

Read more less

The Revo Coolant Relocation Hose offers a high-quality single piece replacement for the OEM part which redirects the hose under the front air scoop to give a more aesthetically pleasing look. COOLANT RELOCATION HOSE The Revo Coolant Relocation hose has been designed and manufactured to directly replace the stock hose found in vehicles with the 1.8T and 2.0T TSI EA888 Gen3 engines. The Revo Coolant Relocation Hose offers a high-quality single piece replacement for the OEM part which redirects the hose under the front air scoop to give a more aesthetically pleasing look.  KEY FEATURES Direct Routing Silicone Hose Improve Aesthetics Coolant caps for easy installation     TECHNICAL DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the MQB Coolant relocation hose instructions   VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A3 / S3 (8V) 1.8 / 2.0 TFSI 12 - Audi TT / TTS (MK3) 2.0 TFSI 14 - Seat Leon (MK3) 1.8 / 2.0 TSI 15 - Skoda Octavia (Mk3) 1.8 / 2.0 TSI 13 - Skoda Superb 2.0 TSI 15 - VW Golf (Mk7) 1.8 / 2.0 TSI 12 -

Read more less

Only The Driven know that the cooler the air, the more power produced. Revo Intercoolers drastically improve your vehicles ability to cool air compressed by the turbo. Increased volume and surface area, bar and plate cores with end tanks specifically designed to promote even airflow all play a part in lowering temperatures; without negatively affecting pressure. REVO AIR INTERCOOLER MQB 1.8/2.0 TSI EA888 GEN3 The Revo Intercooler utilises unique design features to lower intake air temperatures, minimise pressure drop and allow the engine to produce impressive power and torque with Revo Software. The unique end tank profile promotes internal laminar flow by decreasing turbulence and increasing airspeed into the bar and plate core. This enhances charge air cooling giving you access to more power throughout the rev range. The limitations of the stock intercooler were apparent throughout testing. The stock part consistently struggled to manage charge air temperatures, even under normal driving conditions. The Revo Intercooler has been designed to improve on every restrictive element of the stock cooler, enhancing cooling efficiency by lowering intake air temperatures by up to 36ºC vs. the MQB Golf R intercooler, allowing you to drive harder, for longer. KEY FEATURES Bar & Plate Core Design Fully Cast End Tanks OEM Fitment Up to 51% Increased Core Volume Over 36ºC Lower AIT INCREASED CORE VOLUME The Revo Intercooler was built around a simple principle; create a cooler that can keep up with your demand for power. Designed from the ground up, the Revo Intercooler has much larger core volume than the OEM part and offers perfect fitment, improving cooling by utilising the full volume of the stock location space as well as cold ambient air from the front of the vehicle. END TANK DESIGN The stock end tanks are inefficiently designed and create turbulent air in corners. These sections create a natural flow distribution but slow charge air and increase pressure drop. The Revo end tank geometry maintains the largest possible cross-sectional flow area to and from the core. Coupled with a cast interior surface finish, the Revo end tanks allow air to flow freely without obstructions from turbulent air pockets found in the OE intercooler. End tanks play an important part in maintaining pressure and work in harmony with the core to promote airflow, the Revo end tanks are designed to offer the optimal balance between both of these key features.   BAR AND PLATE CORE Designed with a bar and plate core to maximise the efficiency of heat transfer, the pressure drop is also controlled as the air meets less resistance compared to that of a tube and fin alternative. The Revo Intercooler also features carefully specified fin geometry to maximise cooling properties while minimising flow restriction. The ambient core side utilises louvred fins to slow ambient air flow which improves heat transfer, while the charge core side features an offset internal fin design to balance surface area and air resistance to minimise pressure drop.   SILICONE HOSES Supplied with stronger oil resistant silicone hoses, the Revo Intercooler can be installed using the stock pipework or recommended Revo Intercooler pipework. The internal diameter of each silicone is precisely matched to the outer diameter of the ribbed inlet and outlet connections along with a unique Flush Fit design, allowing a smooth transition between components.   BRACKETS To ensures precision fitment, Only Revo offers a CNC machined bracket system. Produced to a superior tolerance than that of a cast mounting system, this unique feature also ensures that the supporting brackets are strong and less prone to failure.   RESEARCH AND DEVELOPMENT All Revo products are designed in-house using the latest 3D printing technology, CAD and CFD software. Every product is rigorously tested utilising an in-house Hub dyno and Revo data acquisition software. The Revo intercooler minimises turbulence while maximising heat transfer, promoting cooler air temperatures and low-pressure drop. This helps retains power and torque throughout of the rev range as highlighted during controlled Dyno testing. The Revo Intercooler was tested in-house to compare the performance against that of the stock Intercooler. First tested on a vehicle running the OEM Intercooler with Revo Stage 2 software, a Revo air intake system and Milltek downpipe, the Revo Intercooler was then installed and tested in the same controlled environment to highlight the benefits of enhanced cooling. PERFORMANCE DATA Golf GTI with Revo Stage 2 Software, Golf R intercooler and Carbon Series Front Scoop Showing the last of five consecutive dyno runs, the efficiency of the Revo Intercooler over the OEM Golf R intercooler is highlighted. With max gains of +10 HP & +20NM Torque, along with increased performance throughout the entire rev range, the stock intercooler struggles to effectively function in comparison to the Revo Intercooler which remained consistent throughout, losing just 2% peak power over the 5 runs compared to 5% on the stock cooler. INLET TEMPERATURE This is a metric used to confirm that testing on the Revo MQB Intercooler. This is used to show that the air temperatures going into the intercooler were similar for each test, confirming that outlet temperatures shown in the following graphs are purely down to differences in intercooler design/construction. As can be seen, the inlet temperatures during testing were hotter on the Revo Intercooler, yet the Revo intercooler produced the lower outlet temps proving the cooling efficiency. OUTLET TEMPERETURE This graph illustrates the increased cooling performance of the Revo intercooler vs OEM Golf R intercooler over all five runs. The Revo Intercooler keeps temperatures below 49ºC on the fifth run, lower than the stock on its first at 58ºC.     FITMENT VEHICLE APPLICATIONS Manufacturer Model Engine Year Audi A3 8V 1.8 / 2.0TSI 2012 > Audi S3 8V 2.0TSI 2012 > Audi TT / TTS 2.0TSI 2015 > Seat Leon 1.8 / 2.0TSI 2013 > Skoda Octavia 1.8 / 2.0TSI 2013 > Skoda Superb 1.8 / 2.0TSI 2015 > VW Golf Mk7 / Alltrack / Sportwagen 1.8 / 2.0TSI 2013 > VW Golf Mk7 GTI / R 2.0TSI 2014 > VW Passat 1.8 / 2.0TSI 2015 > VW Tiguan 2.0TSI 2016 > VW Touran 2.0TSI 2016 > DOCUMENTS The following documents are available to view: FITTING INSTRUCTIONS Download the Revo MQB Golf / Octavia / Leon Intercooler Instructions FITTING INSTRUCTIONS Download the Revo MQB A3 / S3 Intercooler Instructions NOTES Simple replacement of the OEM part Also available for the Golf Mk5/6 MLB Platform Will not fit on cars with O2 sensors fitted without interference on the sensor. It is recommended to speak with your dealer before if you are unsure.

Read more less

Beautifully crafted from the highest quality 3K carbon, the Revo Carbon Series is much more than a visual enhancement. Designed to directly replace restrictive OEM components, the Carbon Series has performance woven in to the core of every product. REVO CARBON SERIES - AIR INTAKE SYSTEM The Revo Carbon Series Air Intake System for the 2.0 & 1.8TSI offers unparalleled performance benefits along with a striking visual addition to your engine bay. The full kit, which comes complete with a matching Carbon Series front scoop, lid, back-pipe and Pro-Panel filter completely replaces any restrictive elements of the OEM intake system, decreasing turbulence and allowing a larger volume of air to reach the turbo more quickly KEY FEATURES Increased Performance Improves Air Flow Efficiency Carbon Series Quality Replaces Restrictive Stock Turbo Elbow Engineered for both LHD and RHD Fitment 16% Larger Air Box Outlet     FULL KIT INCLUDES 90mm Turbo Inlet Hose Machined Inlet Carbon Air Box Lid ProPanel Air Filter Carbon Front Section Coolant Relocation Hose RESEARCH AND DEVELOPMENT All Revo products are designed in-house, allowing our team of engineers to rigorously test products during the design process. Only Revo offers a kit with a 16% larger lid outlet and matching hose, ensuring maximum performance at even Stage 3 and above specification.   GRAPHS To ensure this product would meet our exacting standards and performance, we carried out controlled testing on a Stage 4 Skoda Octavia VRS 2.0TSI running Shell vPower pump fuel on an in-house Dynapak hub dyno. With impressive results in comparison to the standard set up, peak results showed up to +41 WHP and +42 NM over stock with an average of +19whp and +25NM throughout the rev range.     VEHICLE APPLICATIONS   Manufacturer Model Engine Year Audi A3 (8V) 1.8 / 2.0 TFSI 12 - Audi S3 (8V)/td> 2.0 TFSI 12 - Audi TT (MK3) 2.0 TFSI 15 - Audi TTS (MK3) 2.0 TFSI 15 - Seat Leon (MK3) 1.8 / 2.0 TSI 12 - Skoda Octavia (MK3) 1.8 / 2.0 TFSI 12 - Skoda Superb 2.0 TSI 15 - Seat Ibiza Cupra 1.8 TSI 15 - Volkswagen Golf (MK7) 2.0 TSI GTI 14 - Volkswagen Golf (MK7) 2.0 TSI R 14 - Volkswagen Golf (MK7) 1.8 TSI 12 - * Fitments for 1.8 TSI & 2.0 TSI Engines with IHI IS20 and IS38 Turbos INDIVIDUAL PRODUCTS Carbon SeriesCarbon Lid & Hose Kit Carbon SeriesCarbon Scoop Carbon Series Secondary Breather Revo Carbon Series air intake systems perform beautifully. Designed to function no matter the power, Carbon Series intakes look great because of their effective design.

Read more less

Revo ProPanel FilterHigh-Performance Air Filters OVERVIEW The Revo ProPanel is a high-grade direct replacement filter for your vehicle. Designed as direct replacement filters to fit inside your factory air box and are suitable for road or competition use.   BENEFITS Designed to increase horsepower and rate of acceleration Exceptional filtration High airflow with three layers of foam Lifetime warranty Lasts up to 60,000 miles before cleaning is required depending on driving conditions Works with original manufacturers air box   DESIGN AND PERFORMANCE Why choose foam? Because, compared to paper or other filter technologies, reticulated polyester foam achieves optimum performance against three key criteria: Maximum airflow: the ability to allow air to pass through without causing a large drop in pressure. Cleaning efficiency: the capability to arrest a high proportion of airborne dust while feeding the engine clean air. Dust load-up tolerance: the capability to absorb a large amount of dust without reducing airflow capacity. This design of filter has been used in all fields of motorsport from Formula 1 to the World Rally Championship. The range receives this same attention to detail at the design stage and is then taken into production with consummate quality.   THREE LAYER FOAM SYSTEM Revo ProPanel Filters use multi-layered foam technology to trap dust and dirt while maintaining flow efficiency over time. Using foam increases the filter's surface area and is washable, compared to standard paper and cotton filters which trap dust on the surface and become less efficient the more they are used, choking the engine and reducing performance. The outer core is a coarse foam designed to trap larger particles, the second layer is a medium foam designed to trap most particles and the inner core is fine foam which will trap any particles small enough to reach it. The triple layer foam design ensures an exceptional level of engine protection and long-term performance advantage.     1: Stainless steel wire mesh To avoid erosion, only the highest quality steel is used.   2: Course outer layer:  Stops large pieces of dirt and foreign matter from penetrating further. Straightens airflow into subsequent layers.   3: Medium grade middle layer:  This second filtration layer traps most of the harmful dirt that leads to engine damage.   4: Fine inner layer:  Extracts fine particles while allowing full air flow to the engine for maximum power.     ADVANTAGES OF A REVO PROPANEL FILTER Emissions legal in all 50 US states Will not void vehicle warranty Lifetime warranty (to original purchaser with proof of purchase)     FITTING        Manufacturer Model Engine Year Audi A3 (8V)  1.8 / 2.0 TFSI  2012 > Audi A3 (8V)  1.6 / 2.0 TDI  2012 > Audi TT (Mk3)  1.8 / 2.0 TFSI  2014 > Audi TT (Mk3)  2.0 TDI  2014 > Seat Leon (Mk3)  1.8 / 2.0 TSI  2012 > Skoda Octavia (MK3)  1.8 / 2.0 TSI  2013 > Skoda Octavia (MK3)  1.6 / 2.0 TDI  2013 > Skoda Superb (Mk3)  1.8 / 2.0 TSI  2015 > Skoda Superb (Mk3)  1.6 / 2.0 TDI  2015 > VW Golf Vll (Mk7)  1.8 / 2.0 TSI / GTI / R  2012 > VW Golf Vll (Mk7)  1.6 / 2.0 TDI / GTD  2012 > VW Golf Vlll (Mk8)  GTI 2.0 TSI  2019 > VW Golf Vlll (Mk8)  2.0 TDI  2019 > VW Passat  1.8 / 2.0 TSI  2014 > VW Passat  1.6 / 2.0 TDI  2014 > VW Polo GTI  2.0 TSI  2018 > VW Tiguan  2.0 TSI  2016 > VW Tiguan  2.0 TDI  2016 > VW Touran  1.8 TSI  2015 > VW Touran  1.6 / 2.0 TDI  2015 >

Read more less