Forge Motorsport Shop

With the success of FMINDK30 we took the opportunity to revisit the UP GTI and looked to see if we could improve on the 1.0 TSI air flow to the turbo charger. On investigation we could see that the OEM turbo adaptor was very restrictive and was an area in need for improvement. Therefore, our highly skilled development team got to work designing a solution to maximize the capacity by using our CAD system and physical prototypes. The OEM plastic turbo inlet includes a restrictive ribbed and hollow noise chamber that is designed to disturb the air flow and reduce induction noise, this OEM part has a detrimental effect to the engines performance especially when tuned. For the best possible gains, we removed the chamber allowing us to increase the volume and air flow significantly. Our hose design also has an internal stepped area where it is positioned and joined to the turbo housing, this is to ensure the transition is as smooth as possible from the inlet tract to the turbo. Several different designs and material choices were tested until we arrived with the product you see here. The construction of FMTIA3 is manufactured from reinforced multi ply silicone which is more durable than the OEM plastic pipe and it will also not suffer from heat soak like other similar products available. With its enlarged capacity and less restrictive surface area it routes air directly into your turbo charger and allows a greater volume of air to be compressed, this can have a positive effect on accelerating your vehicle after long deceleration or in between gear changes due to more air being kept within the inlet tract to the turbo charger. One significant feature of FMTIA3 is its compatibility with vehicles equipped with and without the PCV system integrated into the existing turbo intake, the early engines do not have the breather system in place from the fuel tank to the elbow. We supply the necessary hardware to blank of the elbow spouts if its required to fit the turbo inlet adaptor to the earlier engine revision The one way valve and coupler adaptor are also supplied so the elbow can be installed to the newer revised engine. The FMTIA3 is also compatible with the factory air box, however for the best performance results we recommend using our intake systems for your particular chassis application.   This is a product which is essential when tuning the 1.0 TSI engine, if its either stage one or stage two tuning we have seen consistent gains from 3-5 bhp depending on the vehicles state of tune. This is a straightforward yet very effective power increasing modification that can be fitted with basic tools and has a typical installation time of around 60 minutes. As with all Forge products it includes a full set of comprehensive installation instructions to make fitting as straightforward as possible. The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone. This means the hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically Increased capacity  No engine check lights (EML) Increased air flow Lifetime warranty* FITS: >> AudiA1A1 (8X) 2010-20181.0 TSI 2015-2021 A1 (GB) 2018-1.0 TSIA31.0TSI>> SeatArona1.0 TSIIbizaMk5 (KJ) 2017 - late 20211.0 TSILeonMk3 2012-20201.0 TSI 2015-2020Toledo1.0 TSI >> SkodaFabiaNJ 2014-20211.0 TSI Octavia1.0 TSI (2018-2021)Rapid1.0 TSI>> VolkswagenGolfMK71.0 TSIMK7.51.0 TSIPolo1.0 TSI T-Roc1.0 116PSUp1.0 GTI/TSI

Read more less

Highlights: Increased performance (8bhp)Guaranteed for lifeComplete kit and instructions for ease of installationHand fabricated aluminium pipingAesthetically pleasing designPerfect with our inlet duct (FMINLD3)   fits:•    500•    595  - 145BHP  - Competizione 180BHP  - Trofeo 160BHP  -  Turismo 165BHP•    695  -  XSR Yamaha Limited Edition 165BHP  -  Rivale 180BHP The cold air feed is drawn in from the scuttle panel, this maximises the density charge of air entering the turbo intake. A perfect upgrade to compliment this is our Abarth specific inlet duct, FMINLD3. This combination of temperature and density gave us an 8bhp increase on our test cars as well as an incredible induction noise. It will put a smile on your face not only when you feel the power gains, but also when you open the bonnet and see this beautiful product sat in your engine bay. Our intakes/induction kits are a great and effective upgrade to your vehicle. This intake comes with a carbon fibre housing. To ensure we deliver the best quality products we can, and following the extensive design and development of our intake range, we enlist the services of one the world’s leading carbon fibre manufacturers, who’s products range from F1 aero, carbon fibre car bodies, and aircraft wings! Our intakes maximise the density charge of cold air for increased performance, as well as give a great sound, and enhance the aesthetics of your engine bay. When it comes to the filtration part of the intakes, there is no point creating such an efficient system for it then to be restricted by the OEM hose and filter. Therefore, for the filters, we engage one of our partners and experts in filtration control, Pipercross or RamAir! Additional parts such as aluminium piping are hand fabricated and polished, and the hoses are fluorosilicone for maximum longevity. This kit for the Fiat 500/595/695 comes with everything you need for the installation. It uses a high flow filter, available in either a foam (FMPK371) or pleated option (FMINDF500RCP). The aluminium components are skilfully hand fabricated in our UK headquarters. 

Read more less

When looking at the B58 engine within the M140i/240i/340i/440i engine bay it’s clear that BMW had left some room for modification within the inlet tract, the sound resonator and accordion ribs cause significant turbulence to the airflow causing a detriment to the engine’s potential performance. By removing these, and replacing it with five-ply silicone construction you gain a host of performance upgrades, including: Significant power gain of over 9bhp engine power and 7nm of torque. Improved induction noise. Multi ply silicone construction improves longevity of FMINLH25 over that of the OEM hose. 5 ply silicone construction will be able to handle strain of engine mapping far better than OEM hose. Fitting with no specialist tools in approximately half an hour.   Vehicle Fitment: BMW 1 Series F20/F21/F40 3/5 Dr Hatchback 2012 Onwards M140i 2016-2019 (B58) 2 Series F22/F23 2Dr Coupe/Convertible 2014 Onwards M240 2016-2021 (B58) 3 Series F30/F31 Saloon/Estate 2011-2019 340i 2015-2019 (B58) Testing was completed using Performance Remap in Gloucester with their VTEC 4 wheel drive dynamometer, This was to ensure all our data has been achieved with results as accurately as possible by an independent tuner. The results below speak for themselves, also with the added benefit of being a very easy component to fit with no specialist tools this is superb, affordable modification for the BMW enthusiast. From the dyno graph shown, performance gains can be expected from 4500RPM to the red line with +9BHP and +7NM of torque at peak RPM. Not only is FMINLH25 a functional improvement, but with it being available in black and red this product really helps to improve the aesthetics of the engine bay. One major difference of FMINLH25 is the diameter of the hose at the airbox end. Usually this is 85mm diameter, however FMINLH25 is 90mm diameter, and uses a silicone reducer sleeve so that it fits the OEM airbox correctly. This increase of 5mm diameter allows the inlet hose to be used with a wider variety of airbox/intake systems while also increasing the volume and de-restricting the flow of the OEM part,     This product is a direct fit for the OEM part 13718601682 (just the turbo inlet to airbox section). The hoses are suitable to be used with either modern long-life coolants, Organic Acid Technology coolants (O.A.T.) or air containing oil mist. The construction of the hoses has been engineered to exceed that of the OEM fitments and will enhance any engine bay both technically and aesthetically. Lifetime warranty. Why not pair this with our Forge Motorsport replacement high flow panel filter (FMPAN-0172) if you are using the OEM airbox.

Read more less

Forge Motorsport have a worldwide reputation of making industry leading parts for an array of performance vehicles; as such we’ve been able to work with some of most knowledgeable professionals in the tuning industry to produce the most versatile Audi RS3 performance intake on the market. 3D scans of left-hand drive (LHD) and right-hand drive (RHD) RS3 8Y’s and RS3 8V’s gave us 4 separate vehicle scans that we could then pull together into one file that has allowed us to create one intake that fits all 4 variations. So, no matter where you’re based in the world or whether you have an 8V or 8Y RS3, the Forge Motorsport FMINDK47 is the intake for you.   Trying to ensure that our performance intake is a one fit all solution also involved an understanding of how turbo inlets vary across the globe for the RS3 market. The OEM turbo elbow is an aluminium cast part with a 3” inlet tract that tapers down to the factory turbo charger cold side feed. Forge Motorsport offer and manufacture an upgraded silicone inlet elbow and turbo inlet adaptor (FMINLH9) not only to increase the area to the inlet tract but also the volumetric capacity. This has been increased to 3.5”and is the largest available product that fits RHD vehicles (due to space constraints with the brake master cylinder and is not physically possible to increase this size any further). However, this is not a problem on LHD vehicles, and as such there are various 4” variants available. To ensure our intake will work in conjunction with either the stock or any aftermarket inlet elbows on RHD or LHD vehicles we’ve incorporated an innovative solution that will be interchangeable if you wish to further enhance the engine performance of your Audi.  FMINDK47 incorporates and includes modular couplers so that it can fit any size turbo inlet you may choose to run. The machined end of the carbon intake where it meets the inlet tract to the elbow has a 4”(102mm) threaded billet attachment which tapers up to the huge 6” pleated filter on the intake side. At this billet alloy junction, it enables the end user to have interchangeable adaptors. Having this amount of adjustment with a vast increase in airflow allows this product to be suitable for stock or aftermarket turbo inlet solutions whether manufactured from silicone or aluminium. This enables the enthusiast to interchange the adaptors depending on if its currently stock or modified. FMINDK47 will support your RS3 to literally any state of tune.   Keeping inlet air temperatures (IAT’s) low is often a difficult part of developing induction systems, and several different variations were tested with FMINDK47. We decided on keeping the OEM air inlet to feed a specifically designed heat shield which sits flush up to the bonnet. An opening on the side opposite to the engine also helps with vehicles running stage 3+, as there is indirect airflow to this area and during testing a fully closed airbox caused restrictions.   Using carbon fibre brings obvious benefits of strength, weight, and aesthetics. However, a part that is often forgotten is its low thermal conductivity, which means it reduces heat soak and transmission of heat to nearby items. Replacing metal or plastic inlet solutions for FMINDK47 will help decrease IAT’s and increase the volume of air supplied to your vehicles engine that is compressed by the turbo charger. This has a better effect on performance when cool as this is to provide the engine with more oxygen (denser air), thus improving the combustion in each cylinder. In addition, by regulating and reducing the air temperature, it also increases the reliability of an engine by keeping the AFRs (air fuel ratios) in each cylinder at a safe level, which in turn, can increase an engines power due to the air being cooler. A bigger bang is then created within the cylinder, providing the correct amount of fuel is added. This can equate to an increase in BHP and torque.  We use SolidWorks CAD, 3D prints, and numerous dyno sessions to truly unlock the power. Simulation testing played a large part in the design process to help maximise the airflow. The 3D printed prototypes helped with comparing our simulation testing to real world driving conditions. This is a valuable comparison that is used in the top tiers of motorsport, now being brought to your vehicle. Being able to test 3 different 8Y RS3’s on 3 different independent dynos has been of vital importance to our development process. One of these RS3’s was (at the time of writing) the fastest 8Y RS3 in the world making 682Whp with FMINT33, FMINLH9, FMINDK47 installed along with a TTE777 Hybrid Turbo charger, this proves the FMINDK47 has great CFM airflow ratings over the standard intake system on vehicles with such a high state of tune.   The other vehicles tested were a UK RHD 8Y running FMINT33. We then changed out from the OEM turbo inlet to FMINLH9 to confirm the differences in BHP with these extra modifications. We were also able to test on a LHD 8Y that was completely stock.   With a completely stock tune vehicle we were able to see peak gains of 6BHP. However further analysis of the dyno graph shows that this peak BHP figure was produced 200RPM earlier (6097RPM instead of 6298RPM). Additionally, the power curves were smoothed across the entirety of the rev range, with gains seen across the board. To pull out some snapshots from the rev range as examples, at 3000RPM using just FMINDK47 saw an increase of 25BHP, and at 4500RPM there was an increase of 17BHP. Torque figures saw similar gains across the rev range, with a peak torque figure increasing by 17NM at around 100RPM earlier. When we analyse the dyno graph across the rev range, at 3000RPM using just FMINDK47 saw an increase in 55NM and at 4500RPM there was an increase of 23NM.   The gains lower in the rev range are truly impressive from a driver perspective this is where the benefits can be felt and is what typically puts you in your seat when the throttle is pressed. Vehicles with a stock tune, FMINLH9 and FMINT33 already installed hit a torque limiter earlier in the rev range with the addition of FMINDK47, which in turn can limit peak power results due to the engines ECU limiting power transmitted to the gearbox. So, if you have these three products installed, we highly recommend looking to tune your vehicle to really maximise the performance of the modifications installed. It’s worth remembering that this is with a stock ECU and no tune. We know from the independent testing we also completed on mapped cars (such as KSF’s) that the Forge Motorsport products create unparalleled performance.  It’s worth noting that this induction kit offers a massive amount of air to the EA855 EVO DAZA or DNWA engine, which is a must for anyone looking to push the performance of their RS3 when tuning to stage 1, stage 2, and beyond. Not only do you get the BHP performance benefits, but FMINDK47 also offers a greater induction noise from the engine; particularly when on boost, our product testers have reported a more responsive throttle which is to be expected from the impressive low down power gains the Forge intake provides.   FMINDK47 is part of our acclaimed Hi Flow range and will ensure that your vehicle is getting critical cold air. Manufacturing this product our of carbon fibre has ensured that we can give you the biggest RS3 induction kit on the market, with the largest possible volume for maximum smooth airflow. Not only is the Forge part a better option for performance, but the carbon fibre really helps to give the engine bay some character. The weave of the carbon has been optimised to match the carbon on the intake manifold, which really shows the level of detail we put into our designs. The high-quality carbon fibre is prepreg 2x2 twill formed in an autoclave from billet tooling and finished with an anti UV gloss gel coat. The Forge Motorsport lifetime warranty on all hardware products shows the trust we have in the quality of our products while they are being enjoyed on your pride and joy.  The kit comes complete with everything you need for installation, which can be carried out in around 1 hour, including a set of full colour instructions. For such an easy to fit product it truly does create some remarkable gains.  *Please note - the filter is excluded from the Forge lifetime warranty* 

Read more less

Product Description With Forge Motorsport leading the way in aftermarket products for the Hyundai N division vehicles, we are proud to present our Turbo Inlet Adaptor and Intake Tract for the Hyundai i20N. The kit is a full plug and play solution, with a replacement cast turbo inlet adaptor, CNC machined hose couplers, and a silicone high flow inlet hose. Available in a choice of Black, Red, and Performance Blue, the TIA11 will not only increase your Hyundai’s performance, but it also transforms the look and aesthetics of your vehicle’s engine bay.   The size of the inlet elbow has increased by over 170% to maximise the amount of air that can physically flow to the turbo from the inlet tract. The OEM factory alloy cast elbow is small, so we knew that this would be the key component to target as tuners start to increase the boost levels and performance output of the 1.6l turbocharged combustion engine. As well as this, the plastic OEM inlet hose has ribs and steps within the bore, causing detrimental turbulence while disturbing and slowing the airflow. By removing the ribs and steps, the larger Forge Motorsport silicone turbo inlet hose reduces the amount of turbulence over the standard item, enabling better airflow. Why do we use silicone? In the development process we tested an oversized aluminium pipe and found that it started to show signs of heat soak, this had a detriment to the impressive initial power gains. We also found after the third pull on the Dyno, the alloy pipe conducted too much heat on this application and started to decrease the gains. When using silicone, heat cannot be conducted as well, therefore even after six pulls, the silicone hose stayed at a steady temperature and did not decrease the power whatsoever. The inlet pipe fits directly to the factory airbox along with our FMINDK45 performance intake solution. The turbo inlet adaptor improves your vehicles airflow in several ways; designed in a similar way to a conventional velocity stack, it routes the air directly into your turbo charger and allows more air to be compressed due to its larger capacity, this has a positive effect when accelerating your vehicle after long deceleration, or in-between gear changes, due to more air being kept within the intake system. Dyno Results Testing was completed using Performance Remap in Gloucester with their VTEC 4-wheel drive dynamometer, this was to ensure all our data is achieved with results as accurately as possible by an independent tuner. As you can see from the dyno results below, peak power was increased from stock by nearly 7 BHP and 12NM of torque when mated to the OEM airbox and standard factory filter. The best news is that there are significant gains across the entire rev range, meaning that the car will pick up quicker and pull the whole way through to redline. TIA11 also benefits from a 17NM of power gain between 2500 RPM and 3000 rpm, this is right as the power comes in and can really change the feel and power delivery when behind the wheel. To compliment the turbo inlet, it can be matched to our induction kit FMINDK45. As you can see below this gave an increase of 12BHP and a torque increase of 20NM both at peak. These two products really do complement each other superbly both in conjunction, and as standalone modifications. After installing a tuning box, or re-calibrating the ECU with stage one or two tunes, the performance yields can be expected to be a lot higher than the figures stated. Testing on the dyno certainly represents the benefits from such a well-engineered product; this coupled with our Lifetime Warranty is just the reason to choose Forge for your Hyundai’s performance hardware.

Read more less

The turbo muffler delete kit for the Hyundai I20N, this kit replaces the original restrictive compressor outlet with our smooth and turbulence free solution.  The OEM part is located on the outlet of the turbo compressor and its only function is to eliminate as much of the engines acoustics as possible. Where it does a good job of quietening down the audible sounds from the turbo it also disrupts the airflow in an area where it’s not needed.  With Forge Motorsports expertise in this area, we have developed a kit which has removed this baffled chamber in favour with our CNC machined billet adaptor which now creates a smooth transition and uninterrupted air flow track to the intercooler, this aids to increase airflow to the engine adding extra performance especially on tuned vehicles.  A new hose design has been made with an increased internal volume and a construction of fluorosilicone internal and iron oxide external which is designed to withstand extremely high temperatures and pressures, this is why Forge Motorsport gives this product its legendary LIFETIME warranty.    All of these improvements have now created an improved throttle response and an improved ambience due to the increased turbo acoustics.    Installation has been made straight forward with the inclusion of detailed step by step instructions.   The Forge silicone hoses in this kit have been designed to include an expensive inner liner of modified silicone known as Fluorosilicone with a high temperature external iron oxide engineered solution  The construction of the hoses has been engineered to exceed that of the OEM fitments, and will enhance any engine bay both technically and aesthetically  CNC machined 6061 aircraft grade aluminium coupler  Improved turbo air flow  Increased audible sound from turbo  Direct replacement of OEM parts  Limited Lifetime warranty*  Complimentary Products Our uprated valve for the Hyundai i20N and the Elantra N Line has been expertly manufactured and designed in the UK, meaning we can provide the industry leading valve for your vehicle. Specifically designed for the Hyundai, this valve can be used either as a fully atmospheric (blow off) valve, or a recirculating valve! This billet aluminium oil cap will replace your OEM one, leaving your engine bay with a premium and high quality aesthetic. This cap is available in a choice of body colour (black or polished) and a choice of cap top insert (black or polished). This perfectly compliments your i20N!  A set of 4 ultra-high performance brake lines for the Hyundai i20N. These are a direct replacement/upgrade for the OEM brake line set and require no further modifications to fit.This brake hose will perform under the most extreme and harsh conditions, whilst still looking good and performing at the highest level.

Read more less

State of art polymer laminated glass cloth Superb heat barrier qualities Withstands radiant temperatures up to 450°C/850°F Ultra thin for minimal clearance As used in WRC and F1 Each roll is 50mm wide x 5 metres long (2" x 16ft) Adhesive backing for ease of fitting After extensive market research Forge Motorsport are proud to release a state of the art metalized polymer laminated glass cloth with adhesive backing that is both extremely light and capable of handling continuous radiant temperatures of up to 450°C. It reflects up to 80% of all radiant heat, whilst offering weight savings against other heat reflecting materials. Forge Motorsport's gold reflective heat barrier requires minimal clearance and is an extremely pliable material with a pressure sensitive adhesive backing that is easy to apply and remove. As used in WRC and F1, make no mistake this gold reflective heat barrier tape is of excellent quality and superb value for money. When used correctly this tape can be used to protect intake components thus lowering IATs resulting in a more efficient and reliable engine cycle. Typical uses are: Wrapping wiring, inside engine covers, bulkheads and firewalls, boost pipes, fuel lines, under seats, intake pipes, airboxes, engine compartments, fuel cells…  

Read more less

Forge has developed this turbo outlet muffler delete pipe for the 2.0 petrol turbo (TSI) (EA888 GEN4 engine). This will not fit Golf R or Audi S3 8Y as this engine has no OEM turbo muffler. It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve throttle response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part.   On the new Golf GTI engine code DNP, this muffler delete gave an additional 8-10bhp during dyno tests. This will fit OEM part number 06Q145702B  

Read more less

FITS: AudiA31.8 TFSi2.0 FSiTTTMk2TTSMk2 8J (2009-2014)SeatAlteaLeonMk2 2005-2012SkodaOctaviaVRS 2.0 TSI 2013 OnwardsVolkswagenGolfMK6Scirocco 2.0 up to 2016 Product Description This will fit engine codes CAWA, CAWB, CBFA, CCTA, CCTB, CCZB, CCZA (With IHI RHF5 Turbo) Forge have developed this turbo outlet muffler delete pipe for the 2.0 TSI petrol turbo (EA888) engines fitted with the IHI turbo, specifically engine codes CBFA, CCZA, CCTA, and CCZB fitted to the Audi A3, Golf GTi (Mk6), Seat Leon and Skoda Octavia. It has been designed with 3 points of contact to eliminate any possibility of resonation.   This part will enhance the sound of the turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. Complete with flouro lined hose and clamps.  

Read more less

Forge has developed this turbo outlet muffler delete pipe for the 177hp 2.0 petrol turbo (TSI) It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. This product fits:AudiA32.0 FSiTQ32.0 TSI (2011-2014)2.0 TSI (2015-2018)TTMk22.0SeatLeonMk2 2005-2012Cupra 2.0 TFSiSkodaKodiaq2.0L 2016-Octavia2.0 FSiT2.0L  VolkswagenBeetle2013 2.0EOSGolfMK6GTIPassat2.0 FSiTPoloGTI 2.0 2018-2020 AW ChassisScirocco 2.0 up to 2016Tiguan2.0 TSI 2017 Onwards 2.0 FSiT     To confirm compatibility, we have found that this will fit the vehicles that have a MAF sensor in the intake pipe as illustrated below. We recommend that you give yourself 2-3 hours to install this Forge Product   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (EA113 TFSI) engines fitted with the K03 turbo, specifically engine codes AXX and BWA as fitted to the Audi A3, Golf GTi (Mk5), Seat Leon and Skoda Octavia. This will not fit engine code CBFA CCZA CCTA CAWB and CCZB with IHI turbo It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will enhance the sound of the turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. Complete with flourolined hose and clamps. This product fits:K03A31.8 TFSi2.0 FSiTA52.0 TFSITTMk22.0SkodaOctavia2.0 FSiTVolkswagenGolfMK5GTIMK6GTIScirocco 2.0 up to 2016       Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport has developed this turbo outlet muffler delete pipe for the 2.0 petrol turbo (TFSI)  (EA113 engine with K04 turbo). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. Complete with flourolined hose and clamps.  This product fits:K04 AudiS32.0 FSiT (8P Chassis)SeatLeonMk2 2005-2012Cupra K1VolkswagenGolfMK5ED30MK6RSciroccoR   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

​​​​​​Fitting this part increases the airflow into the turbo by replacing the restrictive plastic OEM turbo inlet pipe. This innovative product fits all MQB platforms as well as both left and right hand drive vehicles and is a direct replacement for OEM part code 5Q0129635L. When fitting this part, you will increase the available airflow and create an impressive sound by creating a larger, smoother transition between the turbo inlet hose and compressor housing inlet. An all-aluminium construction that fits with standard inlet hose or aftermarket systems, featuring a precision mandrel bent CNC formed pipe along with a precision CNC high flow machined flange. Twin o-ring seal design between the turbo coupler and inner surface of the turbo inlet ensures no leaks and no debris can be drawn into the turbo internals. This part also fits with our induction hose, FMMK7INDH Increased airflow. All aluminium construction. CNC machined couplers for a precision fit. No check engine lights Black hardwearing powdercoated finish. Compatible with LHD and RHD Up to 8 BHP and 16 ft/lbs or torque improvement Made in Great Britain. FITS: AudiA31.8/2.0 TSI 2015 OnwardsQ32.0 TSI (2015-2018)S1S32.0 TSI (8V Chassis)SQ22.0TSI (2018-2021)TTMk32.0 TSI 2015 OnwardsTTSMk3 8S (2014-2021)CupraAteca(up to 2020)SeatLeonMk3 2012-2020Cupra 280/290/300RSkodaOctaviaVRS 2.0 TSI 2013 OnwardsSuperb1.8 TFSI 2015 onwards280 4x4 DSGVolkswagenArteon(2017-2020)2.0 TSIGolfMK71.8 TFSIGTIRMK7.5GTI RJettaMK7 (2018-2021)2.0 GLIMK7.5 (2021-)2.0 GLIPassat2.0 TSI (2015-2021)PoloGTI 2.0 2018-2020 AW ChassisT-Roc2.0 2018-2021Tiguan2.0 TSI 2017 Onwards   Please Note: In line with our policy to constantly review, revise, and improve our product range, the appearance of the product you receive may differ from the one advertised.

Read more less

Forge Motorsport has developed this turbo outlet muffler delete pipe for the 1.8 and 2.0 petrol turbo (TSI) (EA888 engine). It has been designed with 3 points of contact to eliminate any possibility of resonation. This part will improve the sound of your turbo spooling and improve response due to its sleek single billet design that eliminates the restriction and turbulence caused by the OEM part. This is a direct replacement for Part Number 06H 131 111.

Read more less